Operating instructions

3.10 Main Menu - Profibus - Group 9
9-15 PCD Write Configuration
Array [10]
Option: Function:
Select the parameters to
be assigned to PCD 3 to 10
of the telegrams. The
number of available PCDs
depends on the telegram
type. The values in PCD 3
to 10 will then be written
to the selected parameters
as data values. Alternative-
ly, specify a standard
Profibus telegram in
par. 9-22 Telegram
Selection.
[0]
* None
[302] Minimum Reference
[303] Maximum Reference
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
[351] Ramp 2 Ramp Up Time
[352] Ramp 2 Ramp Down Time
[380] Jog Ramp Time
[381] Quick Stop Ramp Time
[382] Starting Ramp Up Time
[411] Motor Speed Low Limit [RPM]
[413] Motor Speed High Limit [RPM]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[590] Digital & Relay Bus Control
[593] Pulse Out #27 Bus Control
[595] Pulse Out #29 Bus Control
[597] Pulse Out #X30/6 Bus Control
[653] Terminal 42 Output Bus
Control
[663] Terminal X30/8 Output Bus
Control
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[894] Bus Feedback 1
[895] Bus Feedback 2
[896] Bus Feedback 3
[1680] Fieldbus CTW 1
[1682] Fieldbus REF 1
[2013] Minimum Reference/Feedb.
[2014] Maximum Reference/Feedb.
[2021] Setpoint 1
[2022] Setpoint 2
[2023] Setpoint 3
[2643] Terminal X42/7 Bus Control
9-15 PCD Write Configuration
Array [10]
Option: Function:
[2653] Terminal X42/9 Bus Control
[2663] Terminal X42/11 Bus Control
9-16 PCD Read Configuration
Array [10]
Option: Function:
Select the parameters to be
assigned to PCD 3 to 10 of the
telegrams. The number of
available PCDs depends on
the telegram type. PCDs 3 to
10 contain the actual data
values of the selected parame-
ters. For standard Profibus
telegram, see
par. 9-22 Telegram Selection.
[0]
* None
[894] Bus Feedback 1
[895] Bus Feedback 2
[896] Bus Feedback 3
[1500] Operating Hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor Current
[1615] Frequency [%]
[1616] Torque [Nm]
[1617] Speed [RPM]
[1618] Motor Thermal
[1622] Torque [%]
[1626] Power Filtered [kW]
[1627] Power Filtered [hp]
[1630] DC Link Voltage
[1632] Brake Energy /s
[1633] Brake Energy /2 min
[1634] Heatsink Temp.
[1635] Inverter Thermal
[1638] SL Controller State
[1639] Control Card Temp.
[1650] External Reference
[1652] Feedback [Unit]
[1653] Digi Pot Reference
Parameter Description
VLT
®
HVAC Drive Programming Guide
MG.11.CA.02 - VLT
®
is a registered Danfoss trademark 83
3
3