Operating instructions
0-42 [Auto on] Key on LCP
Option: Function:
[0] Disabled No function
[1]
*
Enabled [Auto on] Key is enabled
[2] Password Avoid unauthorized start in Auto mode.
If par. 0-42 [Auto on] Key on LCP is
included in the My Personal Menu, then
define the password in par. 0-65 Person-
al Menu Password. Otherwise define the
password in par. 0-60 Main Menu
Password.
[3] Enabled without
OFF
[4] Password without
OFF
[5] Enabled with OFF
[6] Password with OFF
0-43 [Reset] Key on LCP
Option: Function:
[0] Disabled No function
[1]
*
Enabled [Reset] Key is enabled
[2] Password Avoid unauthorized resetting. If
par. 0-43 [Reset] Key on LCP is included
in the par. 0-25 My Personal Menu, then
define the password in par. 0-65 Person-
al Menu Password. Otherwise define the
password in par. 0-60 Main Menu
Password.
[3] Enabled without
OFF
[4] Password without
OFF
[5] Enabled with OFF
[6] Password with OFF
3.2.6 0-5* Copy / Save
Copy parameter settings between set-ups and to/from the
LCP.
0-50 LCP Copy
Option: Function:
[0]
*
No copy No function
[1] All to LCP Copies all parameters in all set-ups from the
frequency converter memory to the LCP
memory. For service purposes it is recommen-
ded to copy all parameters to the LCP after
commissioning.
[2] All from
LCP
Copies all parameters in all set-ups from the LCP
memory to the frequency converter memory.
0-50 LCP Copy
Option: Function:
[3] Size indep.
from LCP
Copies only the parameters that are independ-
ent of the motor size. The latter selection can be
used to programme several frequency convert-
ers with the same function without disturbing
motor data which are already set.
This parameter cannot be adjusted while the motor is running.
0-51 Set-up Copy
Option: Function:
[0]
*
No copy No function
[1] Copy to set-
up 1
Copies all parameters in the present Program-
ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 1.
[2] Copy to set-
up 2
Copies all parameters in the present Program-
ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 2.
[3] Copy to set-
up 3
Copies all parameters in the present Program-
ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 3.
[4] Copy to set-
up 4
Copies all parameters in the present Program-
ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 4.
[9] Copy to all Copies the parameters in the present set-up
over to each of the set-ups 1 to 4.
3.2.7 0-6* Password
0-60 Main Menu Password
Range: Function:
100
*
[0 - 999 ] Define the password for access to the Main
Menu via the [Main Menu] key. If par. 0-61 Access
to Main Menu w/o Password is set to Full access
[0], this parameter will be ignored.
0-61 Access to Main Menu w/o Password
Option: Function:
[0]
*
Full access Disables password defined in par. 0-60 Main
Menu Password.
[1] Read only Prevent unauthorized editing of Main Menu
parameters.
[2] No access Prevent unauthorized viewing and editing of
Main Menu parameters.
If Full access [0] is selected then par. 0-60 Main Menu Password,
par. 0-65 Personal Menu Password and par. 0-66 Access to
Personal Menu w/o Password will be ignored.
Parameter Description
VLT
®
HVAC Drive Programming Guide
MG.11.CA.02 - VLT
®
is a registered Danfoss trademark 35
3
3