Operating instructions

0-37 Display Text 1
Range: Function:
0 * [0 -
0 ]
In this parameter it is possible to write an individual text
string for display in the LCP or to be read via serial
communication. If to be displayed permanently select
Display Text 1 in par. 0-20 Display Line 1.1 Small,
par. 0-21 Display Line 1.2 Small, par. 0-22 Display Line 1.3
Small, par. 0-23 Display Line 2 Large or par. 0-24 Display
Line 3 Large. Use the [
▲
] or [
▼
] buttons on the LCP to
change a character. Use the [
◀
] and [
▶
] buttons to
move the cursor. When a character is highlighted by the
cursor, it can be changed. Use the [
▲
] or [
▼
] buttons on
the LCP to change a character. A character can be
inserted by placing the cursor between two characters
and pressing [
▲
] or [
▼
].
0-38 Display Text 2
Range: Function:
0 * [0 -
0 ]
In this parameter it is possible to write an individual text
string for display in the LCP or to be read via serial
communication. If to be displayed permanently select
Display Text 2 in par. 0-20 Display Line 1.1 Small,
par. 0-21 Display Line 1.2 Small, par. 0-22 Display Line 1.3
Small, par. 0-23 Display Line 2 Large or par. 0-24 Display
Line 3 Large. Use the [
▲
] or [
▼
] buttons on the LCP to
change a character. Use the [
◀
] and [
▶
] buttons to
move the cursor. When a character is highlighted by the
cursor, this character can be changed. A character can
be inserted by placing the cursor between two charac-
ters and pressing [
▲
] or [
▼
].
0-39 Display Text 3
Range: Function:
0 * [0 -
0 ]
In this parameter it is possible to write an individual text
string for display in the LCP or to be read via serial
communication. If to be displayed permanently select
Display Text 3 in par. 0-20 Display Line 1.1
Small,par. 0-21 Display Line 1.2 Small, par. 0-22 Display
Line 1.3 Small, par. 0-23 Display Line 2 Large or
par. 0-24 Display Line 3 Large. Use the [
▲
] or [
▼
] buttons
on the LCP to change a character. Use the [
◀
] and [
▶
]
buttons to move the cursor. When a character is
highlighted by the cursor, this character can be
changed. A character can be inserted by placing the
cursor between two characters and pressing [
▲
] or [
▼
].
3.2.5 0-4* LCP Keypad
Enable, disable and password protect individual keys on the
LCP.
0-40 [Hand on] Key on LCP
Option: Function:
[0] Disabled No function
[1]
* Enabled [Hand on] Key enabled
[2] Password Avoid unauthorized start in Hand mode.
If par. 0-40 [Hand on] Key on LCPis
included in the My Personal Menu, then
define the password in par. 0-65 Person-
al Menu Password. Otherwise define the
password in par. 0-60 Main Menu
Password.
[3] Enabled without
OFF
[4] Password without
OFF
[5] Enabled with OFF
[6] Password with OFF
0-41 [Off] Key on LCP
Option: Function:
[0] Disabled No function
[1]
* Enabled [Off] Key is enabled
[2] Password Avoid unauthorized stop. If
par. 0-41 [Off] Key on LCP is included in
the My Personal Menu, then define the
password in par. 0-65 Personal Menu
Password. Otherwise define the
password in par. 0-60 Main Menu
Password.
[3] Enabled without
OFF
[4] Password without
OFF
[5] Enabled with OFF
[6] Password with OFF
Parameter Description
VLT
®
HVAC Drive Programming Guide
34 MG.11.CA.02 - VLT
®
is a registered Danfoss trademark
3
3