Operating instructions

F
[Fan 1 Area In2] 20-35 127
[Fan 1 Area M2] 20-34 127
[Fan 2 Area In2] 20-37 127
[Fan 2 Area M2] 20-36 127
Fan Control 14-52 106
Fan Monitor 14-53 106
Fault Messages 191
Fc Closed Loop 121
Fc Port Ctw 1 16-85 117
Fc Port Ref 1 16-86 117
Fc Type 15-40 111
Feedback 121
Feedback & Setpoint 124
Feedback 1 Conversion 20-01 122
Feedback 1 Source 20-00 121
Feedback 1 Source Unit 20-02 122
[Feedback 1 Unit] 16-54 115
Feedback 2 Conversion 20-04 123
Feedback 2 Source 20-03 123
[Feedback 2 Unit] 16-55 115
Feedback 3 Conversion 20-07 123
Feedback 3 Source 20-06 123
[Feedback 3 Unit] 16-56 115
Feedback Adv. Conversion 127
Feedback Function 20-20 124
[Feedback Unit] 16-52 115
Fieldbus Ctw 1 16-80 117
Fieldbus Ref 1 16-82 117
Fire Mode 161
Fire Mode Alarm Handling 24-09 164
Fire Mode Configuration 24-01 162
Fire Mode Feedback Source 24-07 164
Fire Mode Function 24-00 162
Fire Mode Live Zero Timeout Function 6-02 69
Fire Mode Log: Date And Time 18-12 120
Fire Mode Log: Event 18-10 119
Fire Mode Log: Time 18-11 120
Fire Mode Max Reference 24-04 163
Fire Mode Min Reference 24-03 163
Fire Mode Preset Reference 24-05 163
Fire Mode Reference Source 24-06 163
Fire Mode Unit 24-02 162
Fixed Lead Pump 25-05 168
Fixed Speed Bandwidth 25-22 169
Flow At Design Point 22-89 150
Flow At Rated Speed 22-90 150
Flow Compensation 148, 149
Flying Start 1-73 43
Flystart Test Pulses Current 1-58 42
Flystart Test Pulses Frequency 1-59 42
Freeze Output 6
Frequency 16-13 113
[Frequency %] 16-15 113
Frequency Converter Ordering No 15-46 111
Frequency Converter Serial Number 15-51 111
Function At Inverter Overload 14-61 107
Function At Mains Imbalance 14-12 103
Function At Over Temperature 14-60 106
Function At Stop 1-80 43
Function Relay 5-40 64
Function Set-ups 19
G
General Warning 4
Graphical Display 10
H
[Hand On] Key On Lcp 0-40 34
Heatsink Temp. 16-34 114
[High Speed Hz] 22-37 143
High Speed Load Compensation 1-61 42
[High Speed Power Hp] 22-39 143
[High Speed Power Kw] 22-38 143
[High Speed Rpm] 22-36 143
Historic Log 110
Historic Log: Date And Time 15-23 110
Historic Log: Event 15-20 110
Historic Log: Time 15-22 110
Historic Log: Value 15-21 110
How To Operate Graphical (glcp) 10
I
Indicator Lights (leds) 11
Initialisation 24
Initialisation Password 8-75 81
Interval Between Starts 22-76 148
Inv. Max. Current 16-37 114
Inv. Nom. Current 16-36 114
Inv. Overload Derate Current 14-62 107
Inverter Thermal 16-35 114
Investment 23-82 160
Iron Loss Resistance (rfe) 1-36 41
J
Jog 6
Jog Ramp Time 3-80 52
[Jog Speed Hz] 3-11 49
[Jog Speed Rpm] 3-19 50
K
Kty Sensor 192
Kwh Counter 15-02 108
L
Language 0-01 26
Language Package 1 26
Language Package 2 26
Lcp 102 10
Lcp Copy 0-50 35
Lcp Id No 15-48 111
Lead Pump 25-82 175
Lead Pump Alternation 25-50 174
Leds 10
Literature 5
Live Zero Timeout Function 6-01 69
Live Zero Timeout Time 6-00 69
Local Mode Unit 0-05 27
Local Reference 27
Locked Rotor Coefficient 1 24-96 166
Locked Rotor Coefficient 2 24-97 166
Locked Rotor Coefficient 3 24-98 166
Locked Rotor Coefficient 4 24-99 166
Locked Rotor Function 24-95 166
Index
VLT
®
HVAC Drive Programming Guide
MG.11.CA.02 - VLT
®
is a registered Danfoss trademark 227