Operating instructions
Index
"
"i-am" Service 8-74 81
A
Abbreviations 5
Ac Brake Max. Current 2-16 47
Acceleration Time 51
Access To Main Menu W/o Password 0-61 35
Access To Personal Menu W/o Password 0-66 36
Active Set-up 0-10 27
Actual Baud Rate 9-63 86
Actual Number Of Inverter Units 14-59 106
Actual Typecode String 15-45 111
Additional Non-working Days 0-83 37
Additional Working Days 0-82 37
Address 8-31 77
Aeo Minimum Magnetisation 14-41 106
[Air Density Factor %] 20-38 128
Alarm Log 111
Alarm Log: Date And Time 15-33 111
Alarm Log: Error Code 15-30 111
Alarm Log: Time 15-32 111
Alarm Log: Value 15-31 111
Alarm Word 188
Alarm Word 16-90 118
Alarm Word 2 16-91 118
Alarm/warning Code List 186
Alarms And Warnings 184
Alternate If Load < 50% 25-55 174
Alternation Event 25-51 174
Alternation Predefined Time 25-54 174
Alternation Time Interval 25-52 174
Alternation Timer Value 25-53 174
Analog In X30/11 16-75 117
Analog In X30/12 16-76 117
Analog Input 53 16-62 116
Analog Input 54 16-64 116
Analog Input Scaling Value 180
Analog Input X42/1 18-30 120
Analog Input X42/3 18-31 120
Analog Input X42/5 18-32 120
Analog Inputs 6
[Analog Out X30/8 Ma] 16-77 117
[Analog Out X42/11 V] 18-35 120
[Analog Out X42/7 V] 18-33 120
[Analog Out X42/9 V] 18-34 120
[Analog Output 42 Ma] 16-65 116
Auto Derate 106
Auto Energy Optimization Compressor 38
Auto Energy Optimization Vt 38
[Auto On] Key On Lcp 0-42 35
Automatic Motor Adaptation (ama) 1-29 40
Automatic Restart Time 14-21 104
B
Bacnet 81
Bacnet Device Instance 8-70 81
Baud Rate 8-32 77
Baud Rate Select 10-01 88
Brake Check 2-15 47
Brake Energy /2 Min 16-33 114
Brake Energy /s 16-32 114
Brake Function 2-10 46
Brake Power 7
Brake Power Limit (kw) 2-12 47
Brake Power Monitoring 2-13 47
Brake Resistor (ohm) 2-11 46
Break-away Torque 6
Broken Belt Delay 22-62 147
Broken Belt Detection 147
Broken Belt Function 22-60 147
Broken Belt Torque 22-61 147
Bus Controlled 68
Bus Error Count 8-81 81
Bus Feedback 1 8-94 82
Bus Feedback 2 8-95 82
Bus Feedback 3 8-96 82
Bus Jog 1 Speed 8-90 82
Bus Jog 2 Speed 8-91 82
Bus Message Count 8-80 81
[Bypass Speed From Hz] 4-61 57
[Bypass Speed From Rpm] 4-60 56
[Bypass Speed To Hz] 4-63 57
[Bypass Speed To Rpm] 4-62 57
C
Can Protocol 10-00 88
Cascade Controller 167, 168
Cascade Status 25-80 175
Changed Parameters (1) 9-90 87
Changed Parameters (2) 9-91 87
Changed Parameters (3) 9-92 87
Changed Parameters (5) 9-94 87
Changes Made 17
Changing A Group Of Numeric Data Values 23
Changing A Text Value 23
Changing Data 23
Changing Parameter Data 17
Clock Fault 0-79 37
Clockwise Direction 1-06 38
Closed Loop Type 20-70 129, 132
Coast Inverse 18
Coasting 6, 13
Coasting Select 8-50 80
Comm. Option Stw 16-84 117
Communication Option 194
Comparator Operand 13-10 95
Comparator Operator 13-11 95
Comparator Value 13-12 96
Configuration 76
Configuration Mode 1-00 38
Continuous Bin Data 23-61 158
Control Card Temp. 16-39 115
Control Profile 8-10 76
Control Site 8-01 75
Control Source 8-02 75
Control Timeout Function 8-04 75
Control Timeout Time 8-03 75
Control Word 16-00 113
Cooling 44
Copyright, Limitation Of Liability And Revision Rights 4
Cos Filter 1 10-20 90
Cos Filter 2 10-21 90
Cos Filter 3 10-22 90
Cos Filter 4 10-23 90
Cost Savings 23-84 160
Counter A 16-72 117
Counter B 16-73 117
Index
VLT
®
HVAC Drive Programming Guide
MG.11.CA.02 - VLT
®
is a registered Danfoss trademark 225