Operating instructions

ManualsBrandsCOMPRO ManualsComputer equipmentX100 - START UP GUIDE

Q3-4 Application Settings

Q3-40 Fan Functions Q3-41 Pump Functions Q3-42 Compressor Functions

Par. 22-60 Broken Belt Function Par. 22-20 Low Power Auto Set-up Par. 1-03 Torque Characteristics

Par. 22-61 Broken Belt Torque Par. 22-21 Low Power Detection Par. 1-71 Start Delay

Par. 22-62 Broken Belt Delay Par. 22-22 Low Speed Detection Par. 22-75 Short Cycle Protection

Par. 4-64 Semi-Auto Bypass Set-up Par. 22-23 No-Flow Function Par. 22-76 Interval between Starts

Par. 1-03 Torque Characteristics Par. 22-24 No-Flow Delay Par. 22-77 Minimum Run Time

Par. 22-22 Low Speed Detection Par. 22-40 Minimum Run Time Par. 5-01 Terminal 27 Mode

Par. 22-23 No-Flow Function Par. 22-41 Minimum Sleep Time Par. 5-02 Terminal 29 Mode

Par. 22-24 No-Flow Delay Par. 22-42 Wake-up Speed [RPM] Par. 5-12 Terminal 27 Digital Input

Par. 22-40 Minimum Run Time Par. 22-43 Wake-up Speed [Hz] Par. 5-13 Terminal 29 Digital Input

Par. 22-41 Minimum Sleep Time Par. 22-44 Wake-up Ref./FB Difference Par. 5-40 Function Relay

Par. 22-42 Wake-up Speed [RPM] Par. 22-45 Setpoint Boost Par. 1-73 Flying Start

Par. 22-43 Wake-up Speed [Hz] Par. 22-46 Maximum Boost Time Par. 1-86 Trip Speed Low [RPM]

Par. 22-44 Wake-up Ref./FB Difference Par. 22-26 Dry Pump Function Par. 1-87 Trip Speed Low [Hz]

Par. 22-45 Setpoint Boost Par. 22-27 Dry Pump Delay

Par. 22-46 Maximum Boost Time Par. 22-80 Flow Compensation

Par. 2-10 Brake Function Par. 22-81 Square-linear Curve Approximation

Par. 2-16 AC brake Max. Current Par. 22-82 Work Point Calculation

Par. 2-17 Over-voltage Control Par. 22-83

Speed at No-Flow [RPM]

Par. 1-73 Flying Start Par. 22-84 Speed at No-Flow [Hz]

Par. 1-71 Start Delay Par. 22-85 Speed at Design Point [RPM]

Par. 1-80 Function at Stop Par. 22-86 Speed at Design Point [Hz]

Par. 2-00 DC Hold/Preheat Current Par. 22-87 Pressure at No-Flow Speed

Par. 4-10 Motor Speed Direction Par. 22-88 Pressure at Rated Speed

Par. 22-89 Flow at Design Point

Par. 22-90 Flow at Rated Speed

Par. 1-03 Torque Characteristics

Par. 1-73 Flying Start

2.1.7 Main Menu Mode

Select the Main Menu mode by pressing the [Main Menu] key.

The below read-out appears on the display.

The middle and bottom sections on the display show a list of

parameter groups which can be chosen by toggling the up

and down buttons.

Each parameter has a name and number which remain the

same regardless of the programming mode. In the Main Menu

mode, the parameters are divided into groups. The first digit

of the parameter number (from the left) indicates the parame-

ter group number.

All parameters can be changed in the Main Menu. However,

depending on the choice of configuration (par. 1-00 Configu-

ration Mode), some parameters can be hidden.

How to Programme

VLT

HVAC Drive Programming Guide

22 MG.11.CA.02 - VLT

is a registered Danfoss trademark