Operating instructions

NOTE
If a feedback is not used, its source must be set to No
Function [0]. Par. 20-20 Feedback Function determines
how the three possible feedbacks will be used by the
PID Controller.
20-01 Feedback 1 Conversion
Option: Function:
This parameter allows a conversion function to be
applied to Feedback 1.
[0]
*
Linear Linear [0] has no effect on the feedback.
[1] Square
root
Square root [1] is commonly used when a pressure
sensor is used to provide flow feedback
(
( flow ∝ pressure )
).
[2] Pressure
to
temper-
ature
Pressure to temperature [2] is used in compressor
applications to provide temperature feedback using
a pressure sensor. The temperature of the refrigerant
is calculated using the following formula:
Temperature =
A 2
(
ln
(
Pe +1
)
− A 1
)
−
A 3 ,
where A1, A2 and A3 are refrigerant-specific
constants. The refrigerant must be selected in
par. 20-30 Refrigerant. Par. 20-21 Setpoint 1 through
par. 20-23 Setpoint 3 allow the values of A1, A2 and
A3 to be entered for a refrigerant that is not listed in
par. 20-30 Refrigerant.
[3] Pressure
to flow
Pressure to flow is used in applications where the air
flow in a duct is to be controlled. The feedback
signal is represented by a dynamic pressure
measurement (pitot tube).
Flow = Duct Area × Dynamic Pressure
×
Air Density Factor
See also par. 20-34 Duct 1 Area [m2] through
par. 20-38 Air Density Factor [%] for setting of duct
area and air density.
[4] Velocity
to flow
Velocity to flow is used in applications where the air
flow in a duct is to be controlled. The feedback
signal is represented by an air velocity measure-
ment.
Flow = Duct Area × Air Velocity
See also par. 20-34 Duct 1 Area [m2] through
par. 20-37 Duct 2 Area [in2] for setting of duct area.
20-02 Feedback 1 Source Unit
Option: Function:
This parameter determines the unit that is used for
this Feedback Source, prior to applying the
feedback conversion of par. 20-01 Feedback 1
Conversion. This unit is not used by the PID Control-
ler.
[0]
*
[1] %
[5] PPM
20-02 Feedback 1 Source Unit
Option: Function:
[10] 1/min
[11] RPM
[12] Pulse/s
[20] l/s
[21] l/min
[22] l/h
[23] m/s
[24] m/min
[25] m/h
[30] kg/s
[31] kg/min
[32] kg/h
[33] t/min
[34] t/h
[40] m/s
[41] m/min
[45] m
[60] °C
[70] mbar
[71] bar
[72] Pa
[73] kPa
[74] m WG
[75] mm Hg
[80] kW
[120] GPM
[121] gal/s
[122] gal/min
[123] gal/h
[124] CFM
[125] ft/s
[126] ft/min
[127] ft/h
[130] lb/s
[131] lb/min
[132] lb/h
[140] ft/s
[141] ft/min
[145] ft
[160] °F
[170] psi
[171] lb/in
[172] in WG
[173] ft WG
[174] in Hg
[180] HP
Parameter Description
VLT
®
HVAC Drive Programming Guide
122 MG.11.CA.02 - VLT
®
is a registered Danfoss trademark
3
3