Technical data

6 / 60 HBC-series V7 LV small types profi low power
*) Maximal continuous (nominal) current:
Maximal continuous current, without any time limits, is defined as current with full switching (100% motor PWM) with environment temperature 25°C
and with corresponding cooling (air flow, fan or water cooling).
Another important criterion is the phase currents in the full switch. Requested are practically identical (as relates to the current value) as the current
from the battery. If the phase current is significantly higher than the current from the battery (engine overloaded, poorly designed engine, etc.), the
maximum continuous current be proportionally lower.
**) Maximal short time current:
Controller tolerates for a short period increased current The time during which the regulator can deliver this current depends on the intensity of cool-
ing. Adjustable current limit (parameter P19) is calculated from this current.
Recommendations: In case the controller is use with currents higher than ca 50% of the maximal values, we recommend intensive cooling by air flow
or use active cooling using fans or water cooling. This will not only prevent possible overheating of the controller, but you will also
gain higher efficiency of the drive unit (colder controller has lower losses than warm one).
Accessories and options, available combination of HBC controllers
Controllers have in basic version only basic equipment. Features and options can significantly affect by the controller additional equipment
specifications.
Equipment of the controllers in the basic version:
- potentiometer input control (voltage control, 0 up to +3.3V), without switch, internal cooling plate, shring tube, without DC/DC conv.
- ICS-2 connector for setting parameters, reading data from the controller, monitoring, update firmware, connection of external modules
- soldered power cables, length 9/12 cm, cross section see table
Accessories and options:
For concrete hardware specification (or a custom firmware) and for order a specific configuration of the controllers, please use the
"HSBC_ordering_form.xls". Not all combinations are available simultaneously. For questions or inquiries, please contact directly the MGM
compro.
Controller type you can specify in the order according to your specific requirements.
Switch: all controllers may be ordered with a switch (in a safe design - its damage or destroy does not affect the safety of flight
and the model / motor don´t stop working when switch component damaged
Heat sinks (coolers): For more efficient power loss (heat) dissipation, it is possible to optionally mount (from one or both sides depending
on the type of the controller) outer ribbed heat sinks (coolers).
Fans: In case of insufficient cooling air flow it is possible to use heat sinks with fans FAN 05, which significantly improve the
cooling efficiency – active cooling.
Possible order as set FAN 05 separately, with screws, for additional mounting to heat sinks – using of anoth-
er type is strictly prohibited !!!
Water cooling: version with water coolers is available for use in boats or in systems with higher demands for cooling intensity.
Hydro version WP: water and humidity does not get on well with electronics. For significant increase of durability of the controller against
humidity and water, it is optionally possible to apply specialty protective cover (marked as WP). This however does
not mean that the controller with this protection is 100% durable during humidity and water and that it is not necessary
to protect it against these negative effects. The protection does not apply to salt water at all !
Hydro version WR: If you need high protection against water, moisture and dust, you can use controllers with WR modification. It is a thick
layer of special material on the PCB, more expensive solutions. The protection does not apply to salt water at all!
Sensor motors (SE): all types of controllers may be ordered suitable for sensor motors. These controllers may be connected to sensorless
motors as well as sensor motors. In this version is automatically available to the motor temperature measurement.
Battery temperature (BT): controllers have add measuring of battery temperature
Each cell monitoring: all controllers have the option to measure each battery cell with an additional module BMM-16.
Control of braking resistors: All types can be ordered with a connector and power management circuits for braking resistor switch.
Communication: All types can be ordered with a communication interface RS 232 TTL (Rx/Tx).
Telemetry (BC): All types can be ordered with options to connect Tx / Rx modules for telemetry (per channel RS-232 TTL).
Type of controls: All types can be ordered with a control by voltage, PWM, potentiometer, data, logic and signal combinations. You can
also order two control channels (e.g. for a separate function brake / throttle).
The long data record: if necessary, the record can be extended with external module LBB_RT with micro SD card on the length of the order
of weeks. The module is also available in a version with real time. §NA
Cruise Control connection: for all types is available external module CCM1, with which the cruise control function is provided.
External display connecting: for all types are available an external display module can be connected either via the Rx / Tx port (RS 232 TTL).
External modules connecting: for all types of controllers can be connected external modules to a connector ICS-2
Customer changes: if you need non-standard features or behavior of the controller, it is possible to agree on a customer change - please
contact the MGM COMPRO.
time
Nominal (max. continuous) current
Starting current peak
Max. short time current
cca 140%
of nominal current
Up to 280% of nominal current
(depend on temperature, etc.)
100%
140%
280%