Technical data

5 / 60 HBC-series V7 LV small types profi low power
Technical data (valid for 25°C environment temperature)
(valid for control board EF5)
Temperature of the environment: 0°C to 40°C Number of regulation steps: 2048 / full throttle range
Motor controlling: PWM: from 8 up to 32 kHz Max. rpm for 2 poles motor: 250 000 rpm
Suitable for motors: without limits number of poles, motors of classical conception (rotor inside) and also for outrunners (rotor is on the outer
(sensors + sensorless) side), FreeAir, Hacker, Kontronik, Lehner, LRK, Mega, Model Motors, MP JET, MVVS, Neu, PJS, Plettenberg, etc.
Control signal: Positive pulses 1.5  0,8 ms, period 2.5 up to 30 ms / voltage 0 – 3.3V (5.0V) / logic signal / data transfer
DC/DC converter (BEC): 5V, 6V, 7V, 8V / 2A cont, 6A max. (10 sec.), input voltage = 6 up to 35V by type (OPTO versions haven’t BEC !)
Feeding: from batteries: NiCd, NiMH, Li-Ion, Li-Pol, A123, acid (Pb) or others cells
from power supplies: in this case is not permit braking without braking resistors ! or switch-of freewheel !
Also is necessary set parameter P21 to „freewheel, no synchro“.
Cables #1 - #5: with JR gold connectors, 20 cm long, 0.25mm
2
Weight is defined for basic modification, i.e. internal cooling plate, shrinking tube, WP, OPTO, input PWM driving (servocable #1), without switch.
In case of use additional parts as external hetasinks, fans, … weight increase :
dimension HT (ribbed heatsink) : +3,5 mm +7,5 gram (single heatsink = 37,5 ×31×5 mm / 11 gram), take off internal cooling plate
dimension HTW (1× water cooler) : +9 mm +16,5 gram (single heatsink = 37,5 ×31×6 mm / 15 gram, pipes Ø 4 / Ø 3, length13 mm )
dimension HTW (2× water cooler) : +6 mm +15 gram
dimension F (fan) : +10 mm +10 gram (30 × 30 × 10 mm / include screws / 10 gram)
switch (with wire) : + 2 gram
cable #2 - #5 (each one) : + 3,2 gram
DC/DC converter (BEC): + 3 gram
Note: by shortening of power cables to motor and battery (power supply) weight decrease proportionally.
HBC-series TMM
®
xxxxx-3 V 7.xx 4526-3 6026-3 9026-3 12026-3 21026-3
Maximal continuous power: 1,17 kW 1,56 kW 2,34 kW 3,12 kW 5,46 kW
Basic dimensions see picture [mm]
Dimension CL (Filtering capacitors) [mm]: Ø 8 × 17 Ø 8 × 17 Ø 10 × 17 Ø 10 × 17 Ø 10 × 17
Dimension CT (Controller thickness) [mm]: 13 14 17 19 25
Dimension D (M2 threads distance) [mm] +): -- -- 22 24 30
Weight without power cables: 34 g 36 g 48 g 56 g 82 g
Weight with power cables: 47 g 49 g 77 g 91 g 125 g
Feeding voltage: 6 – 26 V 6 – 26 V 6 – 26 V 6 – 26 V 6 – 26 V
No. of feeding cells NiCd / NiMH: 6 – 18 6 – 18 6 – 18 6 – 18 6 – 18
No. of feeding cells Li-Ion / Li-Pol: 2 – 6 2 – 6 2 – 6 2 – 6 2 – 6
No. of feeding cells A123: 3 – 7 3 – 7 3 – 7 3 – 7 3 – 7
Max. continuous current *): 45 A 60 A 90 A 120 A 210 A
Max. short time current : **) 60 A 80 A 120 A 160 A 280 A
On-state FET resistance at 25 °C: 2×0,8 m 2×0,7 m 2×0,4 m 2×0,35 m 2×0,18 m
Possible modification with DC/DC conv.: yes yes yes yes yes
Cables cross section to batt. ■■ / motor ■■■***):2,5/2,5 mm
2
2,5/2,5 mm
2
4/4 mm
2
6/4 mm
2
6/4 mm
2
HBC-series TMM
®
xxxxx-3 V 7.xx 5035-3 10035-3 18035-3 4545-3 9045-3 5063-3 10063-3
Maximal continuous power: 1,75 kW 3,50 kW 6,30 kW 2,025 kW 4,05 kW 3,15 KW 6,30 kW
Basic dimensions see picture [mm]
Dimension CL (Filtering capacitors) [mm]: Ø 8 × 17 Ø 10 × 17 Ø 10 × 17 Ø 10 × 31 Ø 10 × 31 Ø 8 × 31 Ø 10 × 31
Dimension CT (Controller thickness) [mm]: 14 19 25 19 25 13 17
Dimension D (M2 threads distance) [mm] +): -- 24 30 24 30 -- 22
Weight without power cables: 36 g 56 g 77 g 51 g 76 g 37 g 63 g
Weight with power cables: 49 g 91 g 120 g 65 g 105 g 51 g 98 g
Feeding voltage: 6 – 35 V 6 – 35 V 6 – 35 V 9 – 45 V 9 – 45 V 9 – 63 V 9 – 63 V
No. of feeding cells NiCd / NiMH: 6 – 24 6 – 24 6 – 24 9 – 32 9 – 32 9 – 44 9 – 44
No. of feeding cells Li-Ion / Li-Pol: 2 – 8 2 – 8 2 – 8 3 – 10 3 – 10 3 – 15 3 – 15
No. of feeding cells A123: 3 – 9 3 – 9 3 – 9 4 – 12 4 – 12 4 – 17 4 – 17
Max. continuous current *): 50 A 100 A 180 A 45 A 90 A 50 A 100 A
Max. short time current : **) 70 A 140 A 250 A 62 A 125 A 70 A 140 A
On-state FET resistance at 25 °C: 2×1,1 m 2×0,55 m 2×0,28 m 2×1,0 m 2×0,50 m 2×0,65 m 2×0,33 m
Possible modification with DC/DC conv.: yes yes yes no no no no
Cables cross section to batt. ■■ / motor ■■■***):2,5/2,5 mm
2
6/4 mm
2
6/4 mm
2
2,5/2,5 mm
2
4/4 mm
2
2,5/2,5 mm
2
6/4 mm
2
The appearance and the technical data may be changed without prior notice.
+) Notice: available for controllers with two heatsinks
***) Notice: possibly also 2×2.5 mm
2
or 2×4.0 mm
2
respectively 2×6,0 mm
2
upon request
Recommendations: If you use controller for currents higher than circa half of the maximal values, we do recommend intensive cooling by air flow or
use of heat sinks (possibly also active cooling using fans or water cooling). This will not only prevent possible overheating of the
controller, but you will also gain higher efficiency of the drive unit (cooler controller has lower losses than warm one).