Technical data

17 / 60 HBC-series V7 LV small types profi low power
Cooperation with RC Remote Control
When you need or is necessary used industry version of the controller in the model or you want only use transfer path of RC
equipment:
 Receiver and antenna should be placed as far as possible from the motor, controller, the batteries and power leads.
 Controller’s cable #1 connect to the receiver, throttle channel.
 When you use (you have) controller with telemetry (BC version), connect cable #34 to corresponding channel of receiver.
 For OPTO versions (i.e. without BEC) you must use external supply for receiver and servos (receiver battery, external BEC, …)
 For BEC version (here is marking by this version with internal DC/DC converter, need for receiver and servos feeding) you can connect receiver
(safety) battery parallel to BEC for safety increase *), see fig. e)
 When motor rotate to other side than you need, you can swap two motor cables (only for sensorless motors !) or change parameter settings (pa-
rameter Reversal of motor revolution).
 When you want use sensor motor (SE version of controller), make „Automatic sensor settings“ before first start.
 The controller switch is connected safety so that drop-out of BEC voltage is not possible if the switch fails (safe connection).
 Controller is turned-on by open contact of the switch or by connecting the accumulators (applies to versions without the switch).
 When you use more than 4 Lipol cells (more than ca 16V), use „antispark“ resistor for first battery connection, see: Sparking prevent when connect
higher voltage
*) for 5V BEC voltage connect 4 Nixx cells
for 6V BEC voltage connect 5 Nixx cells
for 7V BEC voltage connect 2 A123 cells
for 8V BEC voltage connect 2 Lipol / Li-Ion cells
Connect this battery only after controller is on and disconnect first when switching-off controller.
servo
servo
Receiver
Throttle channel
channels xx
senzorový
motor
switch („s“ version)
servo
Traction
Battery
controller
HBC-series
A
B
C
+
–
TMM xxxx-3
BEC, SE
konektor
EFRA
kabel od
senzorů
servo
servo
Receiver
Throttle channel
channels xx
Not used channel
motor
switch („s“ version)
servo
Receiver
Battery
b) OPTO version
c) BEC version SE (sensored)
servo
servo
Receiver MZK
Throttle channel
channels xx
senzorový
motor
switch („s“ version)
servo
Traction
Battery
controller
HBC-series
A
B
C
+
–
TMM xxxx-3
BEC, SE, BC
connector
EFRA
Sensor
cables
d) BEC version
SE (sensored),
BC (telemetry)
Back data transfer
servo
servo
Receiver
Throttle channel
channels xx
motor
switch („s“ version)
Contacts Open = Controller switch-on
servo
a) BEC version
Traction
Battery
controller
HBC-series
A
B
C
+
–
Traction
Battery
controller
HBC-series
A
B
C
+
–
Servocable #1
Servocable #2
telemetry
With OPTO versions
DO NOT TAKE OUT the core !!!
Notice:
(only for versions with BEC !!!)
If you need to feed the receiver or ser-
vos from some other source than BEC,
carefully take out the central core of the
servo cable connector (red wire) and in-
sulate it properly !
servo
servo
Receiver MZK
Throttle channel
channels xx
senzorový
motor
switch („s“ version)
servo
Traction
Battery
controller
HBC-series
A
B
C
+
–
TMM xxxx-3
BEC, SE, BC
connector
EFRA
Sensor
cables
e) BEC version with safety battery
SE (sensored),
BC (telemetry)
Back data transfer
Servocable #1
Servocable #2
telemetry
Not used channel
Receiver (safety) Battery,
Select by note *)
The easiest way to connect a receiver battery for free channel of the receiver or
receivers in position to connect the receiver battery, like OPTO controllers without
BEC, see Figure b) Opto version