Dome Network Camera Installation Guide Before attempting to set up or operate this camera, please read this quick installation guide and retain it for future reference. Model No.
Copyright © 2012 Compro Technology, Inc. All rights reserved. Trademark Compro Technology is the registered trademark of Compro Technology Inc. SD, SDHC and microSDHC Logos are trademarks of SD-3C, LLC.All other company and product names mentioned in this document are registered trademarks of the respective companies. Restriction No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Compro Technology, Inc.
Compro NC3230 - Installation Guide Contents Table of Contents Important Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Regulatory Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Overview. . . .
Compro NC3230 - Installation Guide Important Notices Regulatory Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
The following is a list of items included in the package. Please check the package contents on your hand. If anything is missing, please don’t hesitate to contact your local distributor.
Compro NC3230 - Installation Guide Hardware Overview Camera Layout No. 4 Name Description 1 IR LED Provides additional lighting in low light conditions 2 Ambient light sensor Feeds information on environmental lighting condition to the camera 3 Lens Vari-focal, f 3~9 mm, F1.2~2.
Name 10 Pan adjustment screw 11 Rotation adjustment Loosen the screw to rotate the lens screw 12 Tilt adjustment screw 13 Screw holes (on the For installing the wall mount bracket bottom) for wall mount bracket 14 Power connector A 3-pin power connector 15 I/O connector For connection with various I/O devices 16 MIC in (pink) For connecting to an external microphone 17 Audio out (green) For connecting to an external speaker 18 Zoom lever Move the zoom lever between Wide and Tele to ad
Compro NC3230 - Installation Guide Digital I/O Connector Block The digital inputs are normally used with security sensors, e.g. passive infrared sensors (PIR), smoke detectors, etc. They work by detecting a change in the state of open and closed circuit. The output ports are normally used to trigger external audio or visual indicators, e.g. sirens or strobe lights, etc.
Before you mount the camera on a dropped ceiling, you must first ensure that the ceiling is robust enough to hold the weight of the camera. Then refer to the following steps. 1. Use the supplied drill template to drill three mounting holes on the ceiling. Then drill a hole for the camera’s protective cap. 2. Secure the camera to the ceiling using the supplied hex cap screws and hexagon nuts.
Compro NC3230 - Installation Guide Re-routing Terminal Cable If necessary, you can have the terminal cable exit from the bottom of the camera. To do so, remove the camera’s top cover first and go ahead to detach the entire terminal cable , along with the plastic cable gland, from the camera. Then unscrew the plastic conduit entry cover on the bottom.
2. Ethernet port on camera: Use a RJ-45 LAN cable to connect the Ethernet port of the IP camera to the Ethernet port of your network hub/router. 3. Power adapter (optional accessory): Attach the power adapter to the camera’s power connector when you are not using the camera’s PoE function. Then connect the power plug to a power outlet. If you intend to use PoE (Power-overEthernet) to power the camera, refer to the next section.
Compro NC3230 - Installation Guide Switch Midspan (PoE Injector) Install Camera Software Prior to installing camera software, make sure you have powered on the Compro IP Camera installed in your home/office network. To begin software installation, insert the installation CD included in the package into the CD-ROM drive of your viewing PC. Make sure your Compro IP camera connects to the same home/office network that your viewing PC connects to.
Adjust the Image Follow the instructions below to adjust the camera's varifocal lens. Adjust Zoom and Focus 1. To adjust the zoom and focus, first remove the protection sheet from the top cover, and then loosen the fixing screw on the top cover to remove the top cover. 2. Loosen the zoom lock lever (labeled in below figure) and move the lever to adjust the angle of view. Then tighten the zoom lock lever. 3.
Compro NC3230 - Installation Guide 60° 180° 60° 180° 3. Loosen the tilt adjustment screw (labeled in below figure) on both sides and then tilt the lens holder (labeled in below figure) to adjust the camera's tilting position. The tilt adjustment range is between +60 degrees to -60 degrees. 4. Tighten the tilt adjustment screws and then, if desired, go on to adjust the rotation of the camera image. 60° 60° 180° \ 180° 60° 180° 5. Loosen the rotation adjustment screw (labeled in below figure).
Change SD Memory Card The camera comes with a 4GB microSD card pre-installed inside the housing. The SD memory card is user-upgradeable. And if you like to replace it, refer to the steps below that explain the procedure. 1. Loosen the fixing screws on the top cover and remove the top cover. 2. Locate the microSD card slot below the camera's LED status indicator. Unplug the digital IO cable and audio cables from the camera, and then push the preinstalled SD card gently to release it. 3.
Compro NC3230 - Installation Guide Operation Access the Camera Find Out the Camera's IP Address Using the iWizard setup utility to search for your Compro IP camera on the LAN network is the easiest way to find out your camera's IP address, as the IP address of your camera will be revealed in the search result. To start searching for your camera using iWizard, double-click on the iWizard icon (or tap Start > Programs > ComproView > iWizard) to launch the iWizard setup utility.
6. And then the reconfirmation dialog box will come up. Please press [Install] twice to install both the "USActiveX.cab" and "ComproClientActivex.cab" on your system. 7. Meanwhile, the Windows Security Alert dialog may appear. Please click [Unblock] to unblock it from firewall. 8. Now you can start using WebVUer on Internet Explorer to watch live video and manage IP camera. Access the Camera over the Internet To view camera video remotely over the Internet, one will need to: 1.
Compro NC3230 - Installation Guide After configuring port forwarding successfully, you can now log on to the IP camera from a remote location by entering the camera's IP address plus its HTTP port number in the location field of Internet Explorer. For example, enter "http://61.220.20.16:80". If you have multiple Compro IP cameras installed, you will need to change the HTTP and RTSP port on them manually so each one of them will use a different port.
CAMERA VIDEO AUDIO System Integration Sensor 1/3" CMOS 2-megapixel sensor Lens Vari-focal, f 3~9 mm, F1.2~2.1, auto ir is, megapixel, IR-corrected Zoom 3X optical, 10x digital (total 30x) Angle of View 31.7° ~ 93° Day/Night Automatically controlled Infrared-cut filter, 18 built-in IR LEDs (effective 20m) Min Illumination IR Mode: 0 lux with IR LEDs on in darkness Color Mode: 1.0 lux Shutter Time 1/5 ~ 1/16000 Sec.
Compro NC3230 - Installation Guide System Integration Local Storage Network Remote Surveillance General Mechanical 18 Triggering Event Analytics, schedule, I/O, network failure Triggering Reaction SMS, snapshot, local/remote recording, e-mail, FTP, alarm output, ComproView® notification SDK Yes Local Storage Built-in microSD slot Format AVI (audio incl.
Environmental Input Voltage DC 12V, or PoE (Power-over-Ethernet) PoE IEEE 802.3af Class 3 Operating Temperature -20~50 ºC / -4~122ºF Humidity 20~80% RH non-condensing OS Microsoft Windows XP SP3, Vista SP1, 7 (x86/x64) Browsing Processor Requirement Web Browser Compro NC3230 - Installation Guide Electrical Intel 2.8 GHz, 2GB RAM Microsoft Internet Explorer 8.0 or above, non-IE browsers require 3rd-party VLC plugin * Specifications are subject to change without prior notice.
Compro NC3230 - Installation Guide Technical Support Information Contact Compro Technical Support If you need any technical support, fill out the online form (http://comprousa.com/en/ form.htm) or directly email to support@comprousa.com. Compro Technology, Inc. www.comprosecurity.com Tel. +886 2 2918 0169, Fax +886 2 2915 2389 4F, No.
www.comprosecurity.com Compro Technology Head Office 3F, No.12, Alley 6, Lane 45, Pao Shin Road, Hsintien District, New Taipei City 231, Taiwan Tel. +886 2 29180169 Fax.
