Analog Video Camera User’s Guide Before attempting to set up or operate this camera, please read this user's guide and retain it for future reference. Model No.
Copyright © 2011 Compro Technology, Inc. All rights reserved. Trademark Compro Technology is the registered trademark of Compro Technology Inc. All other company and product names mentioned in this document are registered trademarks of the respective companies. Restriction No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Compro Technology, Inc.
Contents Compro CP180 - User's Guide Table of Contents Important Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Overview. . . . . . . . .
Important Notices Compro CP180 - User's Guide Regulatory Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Product Overview Compro CP180 - User's Guide Package Contents Contact your local distributor should you find anything missing from the package. 1 2 3 4 Analog camera (with body cap) x 1 Power terminal block x 1 IR terminal block x 1 User's guide x 1 Hardware Overview Body cap – Remove the body cap to mount the lens you purchased. Screw hole – For ceiling mount and bracket. Screw hole – For ceiling mount and bracket. DC auto iris lens connector – Connect to the cable from your DC auto iris lens.
Compro CP180 - User's Guide Note: The camera is configured in digital day/night mode by default, which does not use IR cut filter during daytime and nighttime. And once the positive and negative pole of the IR connector are disconnected, camera image will turn monochromatic. To switch to external day/night mode, refer to the 'D/N Mode Jumper' section. IR Connector Pinout The following describes the pinout of the IR connector used to control IR-cut filter. 2 1 Pin Function 1 3.
Installing Lens The following describes how to attach your lens to the camera. 1. Remove the body cap at the front of the camera. 2. Screw the lens into the camera body. While you’re gently turning the lens clockwise, you will hear a 'click'. Then twist the lens by another one-third inch to firmly secure the lens. If you are installing a DC auto iris lens, connect the lens' control cable to the DC iris connector located at the back of the camera. Connecting Video and Power 1.
Compro CP180 - User's Guide D/N Mode Jumper The D/N mode jumper lets you toggle between digital day/night mode (default) and external day/night mode. In digital D/N mode, the IR-cut filter is always removed. In external D/N mode, the IR-cut filter is used/removed by connecting/disconnecting the positive pole and negative pole of the IR connector. If you wish to externally control the IR-cut filter, follow the description below to switch to external D/N mode. 1.
Operating the Camera Prior to using this camera, enter the setup menu and make the appropriate settings for each item in accordance with the condition of the camera's monitoring area. Listed below is the structure of the setup menu. Setup Item Description LENS Lets you select the iris adjustment mode of your lens. SHUTTER / AGC Available Options Submenu Items AUTO / MANUAL Under 'AUTO': type, mode, speed Allows you to configure the shutter speed and auto gain control function.
Compro CP180 - User's Guide Setup Item 8 Description Available Options Submenu Items PRIVACY Protects sensitive areas in the scene. OFF / ON Under 'ON': area sel, top, bottom, left, right, color, transp, mosaic DAY / NIGHT Configures the day/night function. AUTO / COLOR/ B/W Under 'AUTO': burst, delay cnt, day > night, night > day Under 'B/W': burst NR Provides settings for the digital noise reduction function.
Entering and Navigating the Setup Menu To enter the camera setup menu, press the setting button on the back panel. Press UP/ DOWN/LEFT/RIGHT button to navigate the menu. The currently selected menu item will be highlighted in pink on screen. To modify the setting of a highlighted menu item, simply press the LEFT/RIGHT button. A menu item with the icon indicates it has a submenu. To enter a submenu, select an item with the icon and press the setting button.
Compro CP180 - User's Guide Lens Select the iris aperture control method between 'AUTO' and 'MANUAL' by pressing LEFT or RIGHT button. When 'AUTO' is selected, you can press the setting button to enter its submenu, as shown below. SETUP MENU TYPE MODE SPEED DC AUTO 080 RETURN 'TYPE' lets you select between DC iris and video iris. However, video iris mode is not supported on this camera. For the item 'MODE', you can select 'AUTO' to let the camera automatically adjust the diameter of aperture.
Under 'LOW LUMINANCE', you can choose 'AGC' mode (default setting) to have the camera automatically increase the gain when in low light conditions to produce a brighter image. The 'BRIGHTNESS' item allows you to tailor brightness level to your needs. Manual Shutter / AGC Opt for manual shutter / AGC option when you have selected 'MANUAL' for the 'LENS' item, which then provides a submenu that contains mode, shutter and AGC setting.
Compro CP180 - User's Guide Backlight Switch on/off the backlight compensation function. 'BLC' helps correct the problem of subjects being darker than expected in the image when there are bright lights directly shining behind them. In addition, selecting 'HLC' (High light compensation) will display the extreme bright areas in the scene in black. Picture Adjustment Press the setting button when the icon is highlighted to enter picture adjustment menu.
You can configure the motion detection function here. Switch to 'ON' and then press the setting button to enter its submenu. You can create up to 4 motion detection areas by enabling 'MONITOR AREA' and adjusting the 'TOP/BOTTOM/LEFT/RIGHT' slider separately. You can also adjust the detection sensitivity.
Compro CP180 - User's Guide Day/Night Configure the day/night function by selecting between 'AUTO', 'COLOR' and 'B/W'. When 'AUTO' is selected, press the setting button to enter its submenu as shown below. The 'DELAY CNT' specifies the delay before a switchover. 'DAY NIGHT' and 'NIGHT DAY' determines the lux level at the switching point. Note: Having switched to external day/night mode, please set 'DAY/ NIGHT' as 'COLOR'.
Here you can configure the 2D digital noise reduction function (default: off ). Its submenu includes 3 noise reduction mode: 'Y', 'C', and 'Y/C'. Select any of the three NR modes, highlight the Y or C level, and then press the LEFT/RIGHT button to adjust the slider for Y level (brightness signal) or C level (color signal return). NR NR MODE Y LEVEL C LEVEL OFF - RETURN Camera ID You can create a camera title to be displayed on the screen.
Technical Specifications Compro CP180 - User's Guide CP180 VIDEO Image Device Authentic SONY 1/3" 960H EXview HAD CCD II Digital Signal Processor Authentic SONY Effio-E DSP 12-bit Effective Pixel 976 x 494 / 976 x 582 System Scanning Interlaced Synchronization Internal Resolution Horizontal Color: > 680 TV Lines Black/White: > 700 TV Lines Day & Night Minimum Illumination 0.01 Lux (F1.
AES, AGC White Balance ATW, Push Lock, Anti-Color Rolling, Manual Backlight Compensation BLC, HLC Wide Dynamic Range Digital (ATR) Digital Noise Reduction 2D DNR Compro CP180 - User's Guide Exposure Control GENERAL Multi-lingual OSD Menu English, Japanese, German, French, Russian, Portuguese, Spanish, Chinese Casing Cast aluminum Dimensions 55 X 55 x 113 mm Power Requirement DC 12V, AC 24V, terminal block ENVIRONMENTAL Operating Temperature -10°C (14°F) ~ +50°C (122°F) Storage Temperat
www.comprosecurity.com Compro Technology Head Office 3F, No.12, Alley 6, Lane 45, Pao Shin Road, Hsintien District, New Taipei City 231, Taiwan Tel. +886 2 29180169 Fax.
