Installation Guide
Installation on existing concrete steps
Step 1: Prepare –
Remove any existing coverings from stairs (if applicable). Remove nails, staples and stair nosing
Lightly wire brush the existing steps or sand if required. Surface should be smooth and void of any large imperfections
(see warranty notes below)
Lightly sand the back of the ComposiGrip step cover
Wipe down both surfaces with acetone, paint thinner or similar cleaner.
Ensure all surfaces are clean, dry and free of dust before proceeding
Step 2: Install - Before cutting step cover, ensure pattern match
Measure the length and width of the existing stair tread. Transfer the measurement to the ComposiGrip step cover and cut
accordingly. A circular saw can be used for the majority of the cuts. We recommend using diamond grit tile-cutting blades for
cleanest cut.
For indoor applications
Apply the construction adhesive to the back of the step cover following construction adhesive recommendations
Using a 3/16 x 3/16” adhesive spreader apply adhesive evenly across the entire backside of cover.
Place cover in desired location firmly pushing down on to existing step . Once properly located clamp or place weight evenly
distributed on the cover . Follow adhesive manufacturer’s recommendation for clamping/curing time.
Outdoor applications
We recommend adding masonry fasteners; minimum 1.25” long.
Drill clearance holes for the stainless steel or coated masonry fasteners.
Fasten step cover to the existing stair tread. Ensure the step cover is level and squared. Use a minimum of 5 fasteners per
step cover and fasten in an ‘X’ format (2 at each end and 1 in the middle).
Step 3: Finish - Optional Fill the holes with matching color silicone
Installation on existing concrete landing
Step 1: Prepare –
Remove any existing landing coverings (if applicable). Remove nails, staples and stair nosing
Lightly wire brush or sand the existing landing
Lightly sand the back of the ComposiGrip flat sheet
Wipe down both surfaces with acetone, paint thinner or similar cleaner
Ensure all surfaces are clean, dry and free of dust before proceeding
Step 2: Install - Before cutting flat sheet, ensure pattern match
We recommend adding masonry fasteners; minimum 1.25” long. Measure the length and width of the existing landing. Transfer the
measurement to the ComposiGrip flat sheet & cut accordingly. A circular saw can be used for the majority of the cuts. We
recommend using diamond grit tile-cutting blades for cleanest cut.. Drill clearance holes for the stainless steel or coated masonry
fasteners. Apply the construction adhesive to the back of the flat sheet following construction adhesive recommendations. Using a
3/16 x 3/16” adhesive spreader apply adhesive evenly across the entire backside of sheet. Fasten sheet to the existing landing
with stainless steel masonry fastener. Ensure the sheet is level and squared. Use a minimum of 5 fasteners per sheet and fasten in
an ‘X’ format (2 at each end and 1 in the middle).
Step 3: Finish – Optional Fill the holes with matching color silicone
Improper Installation will Void the Warranty:
ComposiGrip Step Covers are NOT structural parts and are NOT designed to
support full load of step. The load-bearing capacity of each Step Cover is dependent upon the load-bearing capacity of the step it is
covering. Step Cover is not designed to bridge large voids or gaps. Deteriorated steps should be filled or levelled prior to installation
of Step Covers. All voids larger than 2-inch (5 cm) diameter should be filled. Installations on highpoint load applications (such as
‘Bear-Claw’ style gratings) should be made using ComposiGrip high strength Industrial Step Covers.
Jig Saw
Caulking Gun
Hammer
Circular Saw
Measuring tape
Bevel square
Safety glasses
BEFORE/AFTER
Materials Required
Masonry Fasteners
Construction adhesive
Caulking
Acetone
Concrete Step
Concrete Landing
Drill
Step Cover Installation
On Concrete
3E Printed 20 NOV 2013
Comoldco Corporation
www.comoldco.com
Made in Canada
Required Tools
Adhesive Spreader