User`s guide

32
Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide
Settings Menu: IntelliFlo
®
(or IntelliPro
®
pump)
The EasyTouch system communicates with the IntelliFlo pump via a two-wire RS-485 cable (PN 350122). For
more information about the IntelliFlo pump see the IntelliFlo VS Installation and User’s Guide (P/N 357269), for
the IntelliFlo VF pump, see the IntelliFlo VF Installation and User’s Guide (P/N 350075). From the IntelliFlo menu
setting the following pumps can be programmed to run at specific U.S. gallons per minute (GPM) or speed (RPM):
• The IntelliFlo VF (15-130 GPM) and IntelliPro
®
VF (15-130 GPM) pump.
• The IntelliFlo VS+ SVRS (1100-3450 RPM), IntelliFlo VS3050 (400-3110 RPM) and IntelliPro
VS3050 (400-3450 RPM) pump.
How many IntelliFlo pumps will EasyTouch support?
EasyTouch can support a total of two IntelliFlo (or IntelliPro) VF or IntelliFlo VS pumps in any combination with
up to eight GPMs or RPMs per pump. For example pumps can be connected to EasyTouch as follows:
• 1 IntelliFlo VF + 1 IntelliFlo VS
• 2 IntelliFlo VF
• 2 IntelliFlo VS
IntelliFlo
®
VS pump
To access the IntelliFlo or IntelliPro VS menu:
Up or Down button: Choose Pump #1 or Pump #2.
Right button: Select Pump #1 to assign as IntelliFlo VF or IntelliFlo VS.
Right button: Select Pump Type.
Up/Down buttons: Select VS (IntelliFlo VS).
Menu button: Press the menu button to save selection and go to the IntelliFlo VS
menu settings.
Down button: Choose Speeds.
Right button: Access the IntelliFlo VS settings for Pump #1.
Up/Down button: Select the circuit number 1 of 8 (1/8). The default speed for each
circuit correspond to the four speed buttons on the IntelliFlo VS control panel. The
preset speed for each button is: Speed 1 button 750 RPM, Speed 2 button 1500 RPM,
Speed 3 button 2350 RPM, and Speed 4 button 3110 RPM.
Right button: Select RPM to change the pump speed.
Up/Down buttons: Set speed of the pump from 400 to 3110 RPM in increments of
10 RPM (For the IntelliFlo VS), 400-3450 RPM (IntelliPro VS).
Press the Right button to view the circuit names.
Press the Up/Down buttons to assign the circuit: None, Spa, Pool, Aux 1-7,
Feature 1-8, Aux Extra (only if Solar is not selected, see page 25 and 42),
Heater, Pool Heater, Spa Heater, Freeze, Pool/Spa, Solar/Heat. “Aux Extra”
is only available if the Solar output (J17) plug on the EasyTouch motherboard
is not being used for solar equipment.
Right button: Press the Up arrow button and go to the next circuit page settings
(2/8) and repeat the previous steps.
When finished setting up the circuits, press the Menu button to save the settings and
to return to the Settings menu options. Press the button two times to return to the
main screen.
MENU ▼ SETTINGS ▼ INTELLIFLO PUMP # 1
Getting There
▲
Pump #1 1/8
RPM : 1500
Circuit:
[ AUX 1 ]


Pump #1 Type
Type: VS


Pump Type
Speeds
Primimg
Status



Pump #1
Pump #2



iS4/iS10 pump
speed control:
IntelliFlo pump
speed can be
increased or
decreased in
increments from an
iS4 or iS10 spa-side
remote. See “iSx
Pump Control” in
the “Settings” menu
(page 46).