User guide
Table Of Contents
- 3Com Wireless 8760 Dual-radio 11a/b/g PoE Access Point
- Contents
- Introduction
- Installing the Access Point
- Installation Requirements
- Power Requirements
- Safety Information
- Deciding Where to Place Equipment and Performing A Site Survey
- Before You Begin
- Connecting the Standard Antennas
- Connecting Power
- Checking the LEDs
- Wall, Ceiling, or Electrical Box Mounting
- Flat Surface Installation
- Selecting and Connecting a Different Antenna Model
- Installing Software Utilities
- Initial Configuration
- System Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- turbo
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-a
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Troubleshooting
- Index
4-51
Security
Dynamic WEP
(802.1x) only
Authentication: Open System
Encryption: Enable
802.1x: Required
Set 802.1x key refresh and reauthentication rates
Local, RADIUS, or
Disabled
Yes
c
802.1x WPA only Authentication: WPA
Encryption: Enable
WPA Configuration: Required
Cipher Suite: TKIP
802.1x: Required
Set 802.1x key refresh and reauthentication rates
Local only Yes
WPA Pre-Shared Key
only
Authentication: WPA-PSK
Encryption: Enable
WPA Configuration: Required
Cipher Configuration: TKIP
802.1x: Disable
WPA Pre-shared Key Type: Hexadecimal or
Alphanumeric
Enter a WPA Pre-shared key
Local only No
Static and dynamic
(802.1x) WEP keys
Enter 1 to 4 WEP keys
Select a WEP transmit key
Authentication: Open System
Encryption: Enable
802.1x: Supported
Set 802.1x key refresh and reauthentication rates
Local, RADIUS, or
Disabled
Yes
Dynamic WEP and
802.1x WPA
Authentication: WPA
Encryption: Enable
WPA Configuration: Supported
Cipher Suite: WEP
802.1x: Required
Set 802.1x key refresh and reauthentication rates
Local or Disabled Yes
Static and dynamic
(802.1x) WEP keys
and 802.1x WPA
Enter 1 to 4 WEP keys
Select a WEP transmit key
Authentication: WPA
Encryption: Enable
WPA Configuration: Supported
Cipher Suite: WEP
802.1x: Supported
Set 802.1x key refresh and reauthentication rates
Local or Disabled Yes
802.1x WPA2 only Authentication: WPA2
Encryption: Enable
WPA Configuration: Required
Cipher Suite: AES-CCMP
802.1x: Required
Set 802.1x key refresh and reauthentication rates
Local or Disabled Yes
WPA2 Pre-Shared
Key only
Authentication: WPA2-PSK
Encryption: Enable
WPA Configuration: Required
Cipher Suite: AES-CCMP
802.1x: Disable
WPA Pre-shared Key Type: Hexadecimal or
Alphanumeric
Enter a WPA Pre-shared key
Local or Disabled No
Client Security
Combination
Configuration Summary
a
MAC
Authentication
b
RADIUS
Server