User guide
Table Of Contents
- 3Com Wireless 8760 Dual-radio 11a/b/g PoE Access Point
- Contents
- Introduction
- Installing the Access Point
- Installation Requirements
- Power Requirements
- Safety Information
- Deciding Where to Place Equipment and Performing A Site Survey
- Before You Begin
- Connecting the Standard Antennas
- Connecting Power
- Checking the LEDs
- Wall, Ceiling, or Electrical Box Mounting
- Flat Surface Installation
- Selecting and Connecting a Different Antenna Model
- Installing Software Utilities
- Initial Configuration
- System Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- turbo
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-a
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Troubleshooting
- Index
5-148
CHAPTER 5: COMMAND LINE INTERFACE
• If the VLAN ID has not been configured for a client on the RADIUS server,
then the frames are tagged with the default VLAN ID of the VAP interface.
Example
WMM Commands
The access point implements QoS using the Wi-Fi Multimedia (WMM) standard.
Using WMM, the access point is able to prioritize traffic and optimize
performance when multiple applications compete for wireless network
bandwidth at the same time. WMM employs techniques that are a subset of the
developing IEEE 802.11e QoS standard and it enables the access point to
inter-operate with both WMM- enabled clients and other devices that may lack
any WMM functionality.
The WMM commands supported by the access point are listed below.
Table 31 WMM Commands
wmm
This command sets the WMM operational mode on the access point. Use the no
form to disable WMM.
Syntax
[no] wmm <supported | required>
• supported - WMM will be used for any associated device that supports
this feature. Devices that do not support this feature may still associate
with the access point.
• required - WMM must be supported on any device trying to associated
with the access point. Devices that do not support this feature will not be
allowed to associate with the access point.
Enterprise AP(if-wireless g: VAP[0])#vlan-id 3
Enterprise AP(if-wireless g: VAP[0])#
Command Function Mode Page
wmm Sets the WMM operational mode on the access point IC-W 5-148
wmm-acknowledge-
policy
Allows the acknowledgement wait time to be enabled
or disabled for each Access Category (AC)
IC-W 5-149
wmmparam Configures detailed WMM parameters that apply to the
access point (AP) or the wireless clients (BSS)
IC-W 5-150