Specifications

11
MONO INPUTS
Connectors
Neutrik XLR for mics. Phantom Power
available globally from the master section
(condenser mics). 1/4 inch jack for line level
instruments. Mic and line inputs are
balanced. Insert point.
Gain Control
UltraMic™ padless preamp provides 60dB of
gain range. Maximum 22dBu of headroom.
Equaliser Section
Steep 18dB per Octave 100Hz High Pass
Filter.
3-band British EQ with swept mid. ±15dB
at Lo 80Hz, Hi 12kHz and Mid variable
250-6kHz. Q = 1.5.
Auxiliary Section
3 flexible auxiliary controls:
Aux 1 is pre-fader/post EQ for foldback or
stage monitor mixes.
Aux 2 is post-fader/post EQ but switchable
pre-fader/post EQ from the master section.
LexFX dedicated to Lexicon effects (post-
fader/post-EQ).
Pan
To position signal in stereo mix or for
subgroup routing.
Routing Section
Channel can be routed to Mix or Sub
Outputs. Muted until the Channel On is
pressed.
Direct Pre/Post
Allows direct outs to be switched either pre-
fader (live recording to prevent multitrack
levels from being affected by changes to the
FOH mix) or post-fader for studio work.
PFL Solo
Monitor pre-fade signal of a “solo” channel
before it reaches the main mix.
100mm Fader
STEREO INPUTS
Stereo Inputs 9-10 & 13-14
2 simple stereo inputs with phono
connectors. Can be routed to Mix or
Subgroup, with rotary level control.
Stereo Inputs 11-12 & 15-16
2 balanced line 1/4" jacks. Controls include
gain, 2-band EQ (±15dB at 80Hz and
12kHz), and balance. Other controls are
same as mic/line inputs.
GROUP/MASTER SECTION
Connectors are at top of Group/Master
section. Outputs are impedance-balanced.
Subgroup Outputs
2 1/4" jacks send subgroup signal to a
multitrack or additional speakers.
Mix Outputs
2 1/4" jacks send mix signal to PA speakers
or a stereo recorder.
Auxiliary Outputs
2 1/4" jacks send signals to effects units or
monitor/foldback amplifiers.
Mono Sum Output
Useful as additional bass bin send, side fill
feed, mono PA feed or for induction loops.
Mix Inserts
For processing all signals routed to mix
with a compressor/limiter or other device.
Monitor Outputs
For nearfield monitors via an amplifier.
2-Track Return
Two phono connectors allow playback of
master stereo recording or for pre-show
music.
Lexicon Foot Switch
Allows effects to be turned on or off on
stage using a guitar foot-pedal.
Phantom Power
Supplies +48V globally to power
condenser mics. LED indicates +48V
active.
Meters
Two 3-colour, 10-segment bargraph meters
show mix output levels. Peak reading
(PPM). When any PFL or AFL solo is
pressed, both meters switch to show solo
level.
2-Track Return Section
Rotary sets playback level. Pressing 2-TK
switch replaces mix signal with tape return
signal.
Aux/FX Master Section
3 rotaries govern master levels of Auxes 1,
2 and Lexicon effects. Aux 2 switchable
pre/post-fade; each master may be solo’d
after the fader.
Sub-Mix and Mix Faders
Pressing the “Sub to Mix” switch routes
submix buses to the mix. Dual insert
points allow signal processors to be
connected across the mix.
Monitor Phones
For headphones of 200 Ohms or greater
impedance. Rotary governs output level.
LEXICON EFFECTS SECTION
Effects Controls
The Lexicon dual effects section provides
combinations of delay, reverb and chorus.
Each effect has two editable, storable/
recallable parameters.
See Lexicon Effects table on page 7.
Programme Select
Select from 16 pre-programmed effects
combinations.
Parameter Adjust
Param 1 / 2 alter values of two effect
parameters using encoder. Alterations are
held in memory when Parameter switch is
released; User Mode LED indicates an
alteration has been made to factory preset
(restorable).
Lexicon Effects Return
Rotary sets Lexicon effects return level,
routable to Mix or Sub. Internal effects
have access to Aux 1 or 2, allowing you to
add reverb to a foldback mix, or to mix
external effects with the Lexicon processor
to create unique combination effects.
LF and HF EQ curves
Swept Mid EQ curve
High Pass Filter
Lo EQ
±15dB
at 80Hz
Hi EQ
±15dB
at 12kHz
20 100 500 1k 5k 10k 20k
Mid EQ sweepable 250Hz - 6kHz
20 100 500 1k 5k 10k 20k
Steep 18dB/octave 100Hz
High Pass Filter (ordinary
HPF shown dashed)
20 100 500 1k 5k 10k 20k
SPECIFICATIONS – PAGE 25 LEXICON EFFECTS TABLE – PAGE 7