Navibe GB732 GB233 Bluetooth Receiver User manual
Introduction Compass Systems Corp. Tel: +886-2-8751-8598 Email: service@cpss.com.tw Fax: +886-2-8797-3898 Web: www.navibe.com No part of this User’s Manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying recording ,for any purpose other than the purchaser’s personal use, without the written permission of Compass Systems Corp. Information in this User’s Manual is subject to change without notice. Compass Systems Corp.
Introduction WARNINGS WARNINGS Some Some certain certain knowledge knowledge is is required required to to be be well well known known by by the the user user for for proper proper and and safe safe use use of Navibe Bluetooth GPS receiver. Please read this User’s Manual first before operation. of Navibe Bluetooth GPS receiver. Please read this User’s Manual first before operation.
Introduction CAUTION CAUTION The TheGlobal GlobalPositioning PositioningSystem(GPS) System(GPS)isisa asystem systemofof24 24satellites satelliteswhich whichcircle circlethe theearth earth twice twicea aday dayinina avery veryprecise preciseorbit orbitand andtransmit transmitinformation informationtotoearth. earth.
Introduction Thank you for choosing Navibe Bluetooth GPS Receiver! Take it now ------it can be your best friend! Application Conditions: Navibe is designed for outdoors navigation in the temperature range of -20°C~ 70°C. Introduction section gives you a general overview of Navibe features. Reference section tells how to operate the unit correctly and how to connect this unit to your pocket PC step-by-step.
Introduction Chapter I Introduction Section 1 Section 2 Section 3 Section 4 Section 5 Announcement Warnings Caution Welcome to Navibe Table of Contents i ii iii iv v Chapter II Reference Section 1 Hardware Description Section 2 State Table of LED Section 3 Packet PC Setup 1 2-5 6-9 v
Reference DC Charging Jack Hardware Description GPS (Green –LED1) Power Switch Hardware Description Low Power (red) & Battery Charging (Yellow) –LED2 Bluetooth (Blue –LED3) 1 Battery Cover GPS External Antenna Connector (MMCX type)
Reference The Bluetooth GPS has three LED indicators. The first is GPS status LED indicator that is named LED1. The second is Low Power and Charging LED which is named LED 2. The third is Bluetooth status LED that is named LED 3.
Reference LED 2: Middle (Red & Yellow) Low Power & Battery Charging LED Description Color and Action Battery Charged Low Power Red ON N/A Yes Yellow ON Charging N/A Yellow OFF Yes No LED 3: Left (Blue) 3 Bluetooth LED Description Color and Action Bluetooth Connection Blue Flashing Pairing Blue ON Connected
Reference Turn on To turn on the receiver, first, make sure that the battery is loaded securely then push the power switch to “ON” position. The green LED (LED 1) indicator will be flashing for searching GPS satellites. The blue LED (LED 3) indicator will start flashing for searching Bluetooth device. Turn off To turn off the receiver, push the power switch to “OFF” position. All of the LED indicators will turn off.
Reference Bluetooth Device The right LED (LED 3) blue indicator will flash for pairing Bluetooth signals. When connected, the LED blue indicator (LED3) will become to steady on. GPS Status The first LED (LED 1) green indicator will be flashing when searching satellites. When fixed, the LED green indicator (LED1) will become to steady on.
Pocket PC Setup Reference Note: Note: In “Bluetooth: Device Pairing” Pairing” window you will required to enter Pocket PC Setup the Passkey number 0000 when opening the port in your GPS program. 1. Tap “Bluetooth Manager” from Start Menu 2.
Reference 3. Tap Explore a Bluetooth device, then tap Next 7 4. Tap where indicated to choose a device. And select the ID “BT GPS V10” or “BT GPS V20” to continue.
Reference 5. The PDA will begin retrieving services as shown above 6.
Reference 7. Tap Finish to establish the BT GPS V.. Bluetooth GPS connection 9 8.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
