ProLiant ML330e/ML330 Server Maintenance and Service Guide Fourth Edition (March 2001) Part Number 174623-004 Spare Part Number 176670-001 Compaq Computer Corporation
Notice © 2001 Compaq Computer Corporation Compaq, the Compaq logo, ROMPaq, Compaq Insight Manager, ProLiant, and QuickFind Registered in U.S. Patent and Trademark Office. SmartStart is a trademark of Compaq Information Technologies Group, L.P. in the United States and other countries. Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in the United States and other countries. Intel and Pentium are trademarks of Intel Corporation in the United States and other countries.
Contents About This Guide Symbols in Text........................................................................................................... v Important Safety Information .............................................................................. v Compaq Technician Notes ......................................................................................... vi Where to Go for Additional Help ..............................................................................
iv Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Removal and Replacement Procedures continued Expansion Board Guide..........................................................................................2-28 System Board .........................................................................................................2-29 Power Supply .........................................................................................................2-30 Replacing a Battery .............
About This Guide This maintenance and service guide is a troubleshooting guide that can be used for reference when servicing the Compaq ProLiant ML330e/ML330 server. WARNING: To reduce the risk of personal injury from electric shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs can create conditions that are hazardous. Symbols in Text These symbols may be found in the text of this guide.
vi Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Compaq Technician Notes WARNING: Only authorized technicians trained by Compaq can attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module-level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board.
About This Guide Where to Go for Additional Help In addition to this guide, the following information sources are available: ■ User documentation ■ Compaq Service Quick Reference Guide ■ Service training guides ■ Compaq service advisories and bulletins ■ Compaq QuickFind™ information services ■ Compaq Insight Manager software Integrated Management Log The ProLiant ML330e/ML330 server includes an integrated, nonvolatile management log that contains fault and management information.
Chapter 1 Illustrated Parts Catalog This chapter provides the illustrated parts breakdown and spare parts lists for the Compaq ProLiant™ ML330e/ML330 server with an Intel Pentium III processor and a 133-MHz system bus. See Table 1-1 and Table 1-2 for the names of referenced spare parts.
1-2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Mechanical Parts Exploded View 3a 2 3b 4b 1 4c 4a 5a Figure 1-1.
Illustrated Parts Catalog 1-3 Mechanical Spare Parts List Table 1-1 Mechanical Spare Parts List Item Description Spare Part Number Chassis 1 Chassis assembly 2 Front bezel 3 176605-001 ProLiant ML330e server 230542-001 ProLiant ML330 server 176604-001 Panel access left/right 176606-001 a) Hood panel (right) b) Access panel (left) Miscellaneous 4 Hardware kit 176618-001 a) Hard drive compartment b) Removable drive tray c) Expansion board knockout 5 Miscellaneous plastics kit a) Expansion
1-4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide System Components Exploded View 13 6a 9 10 14 15 16a 7 11 12 8a 15 Figure 1-2.
Illustrated Parts Catalog 1-5 System Components Spare Parts List Table 1-2 System Components Spare Parts List Item Description Spare Part Number Mass Storage Devices 6 IDE CD-ROM drive a) IDE CD-ROM drive x32 163354-001 b) IDE CD-ROM drive x40* 179963-001 7 Diskette drive 123958-001 8 Hard drive a) 20-GB ATA hard drive (ML330e model) 230699-001 b) 9.
1-6 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Table 1-2 System Components Spare Parts List continued Item 14 Description Spare Part Number Pentium III processor a) 667/133 with heatsink* 176610-001 b) 733/133 with heatsink* 176612-001 c) 800/133 with heatsink* (ProLiant ML330e and ML330) 176613-001 d) 866/133 with heatsink* 176614-001 e) 933/133 with heatsink* (ProLiant ML330e and ML330) 202350-001 f) 1-GHz/133 with heatsink* 217827-001 15 CR2032 lithium coin cell b
Chapter 2 Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for the Compaq ProLiant ML330e/ML330 server. Run the diagnostics program to verify that all components properly operate.
2-2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Electrostatic Discharge Information An electrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry. Proper packaging and grounding techniques are necessary precautions to prevent damage. To prevent electrostatic damage, observe the following precautions: ■ Transport products in static-safe containers such as conductive tubes, bags, or boxes.
Removal and Replacement Procedures Symbols on Equipment These symbols may be located on equipment in areas where hazardous conditions may exist. This symbol, in conjunction with any of the following symbols, indicates the presence of a potential hazard. The potential for injury exists if warnings are not observed. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel.
2-4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Preparation Procedures WARNING: Only authorized technicians trained by Compaq should attempt to repair this equipment. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
Removal and Replacement Procedures Front Bezel WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. To remove the front bezel: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2.
2-6 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Access Panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them.
Removal and Replacement Procedures Storage Devices The ProLiant ML330e/ML330 server ships standard with seven drive bays, five of which are available. Figure 2-3 shows the location of the storage devices. Table 2-1 shows the corresponding drive bay descriptions. 1 2 3 4 5 6 7 Figure 2-3. Storage device drive bay locations Table 2-1 Storage Device Drive Bay Descriptions Drive Position Description 5.25-inch x 1.6-inch IDE CD-ROM drive bay 5.25-inch x 1.
2-8 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Bezel Blanks To remove a bezel blank from the front bezel: WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded AC outlet. 1. Remove the front bezel. See “Front Bezel” earlier in this chapter. 2.
Removal and Replacement Procedures Drive Tray To remove a drive tray from a removable media bay: WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the access panel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. NOTE: The drive trays in the removable media bays can be used to mount internal 3.5-inch hard drives. 1.
2-10 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide ATA Hard Drive Compartment (ProLiant ML330e Server) To remove an ATA hard drive compartment from the ProLiant ML330e server: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel door. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4.
Removal and Replacement Procedures 5. Remove the three shipping screws , squeeze the two spring clips drive compartment from the chassis . , and then pull the 2 2 3 1 1 Figure 2-7. Removing an ATA hard drive compartment To replace an ATA hard drive compartment, reverse steps 2 through 5.
2-12 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide SCSI Hard Drive Compartment (ProLiant ML330 Server) To remove a SCSI hard drive compartment from the ProLiant ML330 server: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel door. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4.
Removal and Replacement Procedures 5. Remove the three shipping screws , squeeze the two spring clips drive compartment from the chassis . , and then pull the 2 2 3 1 1 Figure 2-9. Removing a SCSI hard drive compartment To replace a SCSI hard drive compartment, reverse steps 2 through 5.
2-14 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Hard Drives To remove a hard drive from the hard drive compartment: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Disconnect all the power and data cables from the back of all drives on the hard drive compartment. 5.
Removal and Replacement Procedures Power Switch IMPORTANT: To completely remove all power from the system, you must disconnect the power cord from the server. To remove the power switch: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Disconnect the power switch cable from the system board. Figure 2-11.
2-16 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide 5. From the front of the chassis, squeeze the sides of the power switch to disengage the two retainer clips from the chassis , and then gently remove the power switch from the chassis . 6. Also from the front of the chassis, squeeze the side of the LED to disengage the two retainer clips from the chassis , and then gently remove the LED from the chassis . 1 1 2 4 3 Figure 2-12.
Removal and Replacement Procedures Fan To remove the fan: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Disconnect the fan power cable from the system board fan connector . 5. Use a Phillips screwdriver to remove the four mounting screws from the rear of the server . 6.
2-18 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Cable Routing Diagrams Figure 2-14 through Figure 2-18 show cable routing diagrams for the ProLiant ML330e/ML330 server. 1 2 Figure 2-14.
Removal and Replacement Procedures Figure 2-15. Server Management Information Cable (SMIC) routing (ProLiant ML330e server) Figure 2-16.
2-20 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Figure 2-17. ATA cable routing (ProLiant ML330e server) Figure 2-18.
Removal and Replacement Procedures Processor with Heatsink To remove a processor with heatsink: CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded (earthed) before beginning any installation procedure. See “Electrostatic Discharge Information” earlier in this chapter for more information. WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. 1.
2-22 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide 5. Press down and release the heatsink retainer clip to disengage one side from the processor socket . 6. Unhook the opposite side of the heatsink retainer clip from the processor socket then lift the heatsink/fan assembly from the processor socket . , and 7. Lift the lever, located on the side of the processor socket, to release the pins of the processor , and then pull the processor from the socket .
Removal and Replacement Procedures Memory Modules The ProLiant ML330e/ML330 server supports 64-, 128-, 256-, or 512-MB PC 133-MHz Registered error checking and correcting (ECC) synchronous dynamic random access memory (SDRAM) dual inline memory modules (DIMMs). CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded (earthed) before beginning any installation procedure.
2-24 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide NOTE: Memory modules do not need to be installed in pairs and can be installed in any available socket. 1 2 3 4 Figure 2-21.
Removal and Replacement Procedures Removing a Memory Module To remove a memory module: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Press outward on both latches of the memory module socket at the same time releases the DIMM and pushes it partially out of the socket. 5. Lift the memory module from the socket .
2-26 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Expansion Slots 1 2 3 4 5 6 Figure 2-23.
Removal and Replacement Procedures Server Feature Board To remove a Server Feature Board: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Disconnect any cables connected to the Server Feature Board. 5. Remove the screw securing the Server Feature Board to the chassis Server Feature Board out of the server .
2-28 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Expansion Board Guide To remove the expansion board guide: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3. Remove the access panel. See “Access Panel” earlier in this chapter. 4. Remove all expansion boards supported by the board guide. 5. Push in the four locking tabs chassis .
Removal and Replacement Procedures System Board CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded (earthed) before beginning any installation procedure. See “Electrostatic Discharge Information” earlier in this chapter for more information. To remove the system board: 1. Complete the preparation procedures. See “Preparation Procedures” earlier in this chapter. 2. Remove the front bezel. See “Front Bezel” earlier in this chapter. 3.
2-30 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Power Supply To remove the power supply: WARNING: To reduce the risk of electric shock or damage to the equipment: ■ Unplug the power cord before removing the power supply from the server. ■ Install the power supply before connecting the power cord to the power supply. CAUTION: To avoid dropping the power supply, pull out and hold the power supply with a firm grip. 1. Complete the preparation procedures.
Removal and Replacement Procedures Replacing a Battery The ProLiant ML330e/ML330 server has nonvolatile memory, which requires a battery to retain system information. There is a battery on the system board and a battery on the Server Feature Board. These batteries are required to maintain certain system data. Replacing the System Board Battery If your server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock.
2-32 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide 4. Locate the battery on the system board, and then slide the battery out of the holder. 5. Slide the replacement battery into the proper position with the positive (+) side up. Figure 2-28. Locating and removing the battery from the system board IMPORTANT: Positive (+) polarity must be positioned up. 6. For the ProLiant ML330 server, run the BIOS Setup utility to reconfigure your system. 7.
Removal and Replacement Procedures Replacing the Server Feature Board Battery WARNING: The Server Feature Board contains a lithium battery. There is a risk of fire and chemical burn if the battery is improperly handled. Do not disassemble, crush, puncture, or short external contacts, dispose of in water or fire, or expose the battery to temperatures higher than 60°C (140°F). CAUTION: Electrostatic discharge (ESD) can damage electronic components.
Chapter 3 Diagnostics Tools This chapter provides an overview of the software and firmware diagnostics tools available for the Compaq ProLiant ML330e/ML330 server.
3-2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Diagnostics Tools Utility Overview The following utilities were developed to assist in diagnosing problems, testing the hardware, and monitoring and managing the ProLiant ML330e/ML330 server hardware. Table 3-1 Diagnostics Tools Tool What it is How to run it Compaq Diagnostics Utility to assist testing and/or verifying operation of Compaq hardware.
Diagnostics Tools Table 3-1 Diagnostics Tools continued Tool What it is How to run it Compaq SmartStart Located on the SmartStart and Support Software CD, SmartStart is the intelligent way to set up your Compaq server. SmartStart includes the ROMPaq™ Utility, driver updates, and assisted operating system installations. Power up from the SmartStart and Support Software CD. Array Diagnostics Utility (ADU) A Windows-based tool designed to run on all Compaq systems that support Compaq array controllers.
3-4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Table 3-1 Diagnostics Tools continued Tool What it is How to run it ROM Based Setup Utility (RBSU) for the ProLiant ML330e server Utility used to configure some hardware installed in or connected to the server. Specifically, it can: Run RBSU directly from the system ROM by pressing F9 when prompted during POST to enter the utility.
Diagnostics Tools For More Information For detailed information about each of these diagnostics tools, see the Compaq Servers Troubleshooting Guide on the documentation CD. For the most recent version of this guide, go to the Compaq website: http://www.compaq.
Chapter 4 Connectors, Switches, and LED Indicators This chapter contains illustrations and tables identifying connectors, switches, and LED locations on the rear panel, Server Feature Board, and system board for the Compaq ProLiant ML330e/ML330 server.
4-2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Connectors This section contains graphics and tables identifying connector locations on the system board, rear panel, and Server Feature Board for the Compaq ProLiant ML330e/ML330 server. System Board Components 15 14 16 17 13 12 9 11 8 10 7 18 19 20 6 21 5 22 4 23 3 2 Figure 4-1.
Connectors, Switches, and LED Indicators Table 4-1 System Board Components Item Description 32-bit PCI slot 6 32-bit PCI slot 5 32-bit PCI slot 4 32-bit PCI slot 3 (Server Feature Board) 64-bit PCI slot 2 64-bit PCI slot 1 (half-length) Battery System fan connector Processor Serial port connector B Parallel port connector Serial port connector A USB ports (ProLiant ML330e server only) Item Description Mouse connector Keyboard conn
4-4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Rear Panel Connectors 1 2 3 4 5 6 7 8 9 Figure 4-2.
Connectors, Switches, and LED Indicators Server Feature Board Components (ProLiant ML330e Server) 2 1 3 9 8 4 7 6 5 Figure 4-3.
4-6 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Server Feature Board Components (ProLiant ML330 Server) 2 1 9 3 8 4 7 6 5 Figure 4-4.
Connectors, Switches, and LED Indicators Switches This section contains graphics and tables showing switch locations on the ProLiant ML330e/ML330 server system board and Server Feature Board. Reserved Processor Switch Settings (SW1) on 1 2 3 4 Figure 4-5.
4-8 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide System Configuration Switch Settings (SW2) on 1 2 3 4 Figure 4-6.
Connectors, Switches, and LED Indicators Server Feature Board Switch Settings (SW1) on 1 2 3 4 5 6 7 8 Figure 4-7. Server Feature Board switch settings (SW1) Table 4-7 Server Feature Board Switch Settings (SW1) Switch 1 Default Function Description Settings Off Enable embedded video Used to disable the onboard video controller when an optional video adapter is installed.
4-10 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Voltage Regulator Switch Set the voltage regulator switch to either 115 volts or 230 volts, as appropriate for your location. 115 230 Figure 4-8.
Connectors, Switches, and LED Indicators LEDs This section contains graphics information on the following LEDs: ■ System status LEDs ■ Network controller status LEDs System Status LEDs 1 2 3 Figure 4-9. System status power button LEDs Table 4-8 System Status LEDs Item Power button Power status Hard drive activity status Status Description System on On System on, AC power OK. Do not remove power from system.
4-12 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Network Controller LEDs 1 2 3 Figure 4-10.
Chapter 5 Physical and Operating Specifications This chapter provides specifications for the Compaq ProLiant ML330e/ML330 server. The following specifications are provided: ■ System Unit ■ Memory ■ 1.
5-2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide System Unit Table 5-1 System Unit Specifications Dimensions Height 42.86 mm (16.88 in) Width 19.05 mm (7.5 in) Depth 50.8 mm (20 in) Weight 10.1 kg (26 lb) weight approximate, depending upon options International input requirements Rated input voltage 180 VAC to 264 VAC Rated input frequency 50 Hz to 60 Hz Rated input current 3A U.S.
Physical and Operating Specifications Memory Table 5-2 Memory Specifications Size 64-, 128-, 256-, and 512-MB, and 1-GB Speed PC 133-MHz Type ECC Registered SDRAM DIMMs 1.44-MB Diskette Drive Table 5-3 1.44-MB Diskette Drive Specifications Size 8.89 mm (3.5 in) LED indicators (front panel) Green Read/write capacity per diskette (high/low density) 1.
5-4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide IDE CD-ROM Drive Table 5-4 IDE CD-ROM Specifications Applicable disk CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA; Photo CD (single- and multiple-session), CD-XA (mode 2, forms 1 and 2); CDI ready; CD-WO Capacity 650 MB Rotational speed 5,200 rpm Block size 2,328 bytes (CD-XA) 2,340, 2,336, 1,024 bytes (mode 2) 2,048, 1,024 bytes (mode 1) 2,352 bytes (CD-DA) Dimensions Height 42.9 mm (1.
Physical and Operating Specifications Table 5-4 IDE CD-ROM Specifications continued Laser parameters Type Semiconductor Laser GaA1As Wave length 780 ± 25 nm Divergence angle 53.5° ± 1.5° Output power 0.14 mW Operating conditions Temperature 5°C to 45°C (41°F to 113°F) Humidity 5% to 90% (10% to 80%) ATA Hard Drives (ProLiant ML330e Server) Table 5-5 ATA Hard Drive (ProLiant ML330e Server) Specifications 20 GB 7.2K rpm Capacity 20,020.0 MB Height 25.4 mm (1 in) Width 88.9 mm (3.
5-6 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Wide Ultra2 SCSI Hard Drives (ProLiant ML330 Server) Table 5-6 Wide Ultra2 SCSI Hard Drive (ProLiant ML330 Server) Specifications 9.1 GB 7.2 K rpm 9.1 GB 10 K rpm Capacity 9,100.0 MB 9,100.0 MB Height 25.4 mm (1 in) 25.4 mm (1 in) Width 88.9 mm (3.5 in) 88.9 mm (3.5 in) Interface Wide Ultra2 SCSI Wide Ultra2 SCSI Transfer rate synchronous (max) 80 MBps 80 MBps Single track 1.9 ms 0.8 ms Average 7.5 ms 5.
Physical and Operating Specifications Integrated 10/100 Wake on LAN Network Interface Controller Table 5-7 Integrated 10/100 Wake on LAN NIC Specifications Network interface 10Base-T/100Base-TX Compatibility IEEE 802.2, 802.3, 802.3u Data transfer method 32-bit, PC 33-MHz bus master Network transfer rate 10/100 Mbps Connector RJ-45 I/O address and interrupt Plug and Play PCI Compliance PCI 2.2 and 2.1 OS support (ProLiant ML330 server) Microsoft Windows NT 4.0, Microsoft Windows NT server 4.
5-8 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide Integrated Ultra ATA 100 Controller Table 5-9 Integrated Ultra ATA 100 Controller Specifications Protocol Ultra ATA 100 Drives supported Up to 2 ATA devices per channel Data transfer method 32-bit PCI bus-master Maximum transfer rate per PCI Bus (peak) 133 MBps ATA channel transfer rate 100 MBps per channel ATA connectors 2 internal
Index A access panel part number 1-3 removing 2-6 caution 2-6 illustrated 2-6 warning 2-6, 2-9 replacing 2-6 access times CD-ROM drive 5-4 diskette drive 5-3 ADU (Array Diagnostics Utility) described 3-3 locating 2-1 Array Diagnostics Utility See ADU ASR (Automatic Server Recovery, running 3-4 ATA (ProLiant ML330e server), cable routing, illustrated 2-20 ATA cable assembly, part number 1-6 ATA hard drive compartment removing 2-10, 2-11 removing cables, illustrated 2-10 removing, illustrated 2-11 replacing
2 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide compartment ATA hard drive removing 2-10 replacing 2-11 hard drive, part number 1-3 SCSI hard drive, removing 2-12 component-level repairs, warning vi, 2-4 cooling, caution 2-4 country kit, part number 1-6 D data transfer rate 32-Bit Dual Channel Ultra ATA 100 Adapter 5-8 32-Bit Dual Channel Wide Ultra2 SCSI Adapter 5-7 diskette drive 5-3 hard drive 5-5, 5-6 Diagnostics accessing 3-2 described 3-2 locating 2-1, 3-2 overview 3-2 diskette
Index help additional sources vii Compaq authorized resellers, telephone numbers vii Compaq website vii technical support, telephone numbers vii hood panel, part number 1-3 hot surface, warning 2-3, 2-4, 2-6, 2-21 I IDE CD-ROM drive See CD-ROM drive IDE ribbon cable assembly, part number 1-6 illustrations access panel, removing 2-6 ATA (ProLiant ML330e server), cable routing 2-20 ATA hard drive compartment removing 2-11 removing cables 2-10 battery, removing 2-32, 2-33 bezel blank, removing 2-8 diskette d
4 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide K P keyboard, part number 1-6 kits country 1-6 hardware 1-3 plastics, miscellaneous 1-3 power cable 1-6 return 1-6 signal cable 1-6 panel access, part number 1-3 part numbers access panel 1-3 ATA cable assembly 1-6 battery 1-6 cable clips 1-3 CD-ROM drive 1-5 chassis 1-3 clamps 1-3 country kit 1-6 diskette drive 1-5 cable assembly 1-6 drive tray 1-3 expansion board guide 1-3 knockout 1-3 fan 1-5 front bezel door 1-3 hard drive 1-5 hard
Index personal injury, warning v, vi, 2-3, 2-4, 2-6, 2-21 physical configuration, hard drive 5-5, 5-6 plastics kit, miscellaneous 1-3 power button, part number 1-6 power cable kit, part number 1-6 power cords, disconnecting, warning 2-4 power extension cable, part number 1-6 power fluctuations, caution 2-4 power shield cable, part number 1-6 power source, warning 2-3 power supply caution 2-30 part number 1-5 removing 2-30 removing, illustrated 2-30 replacing 2-30 power switch removing 2-15 removing, illust
6 Compaq ProLiant ML330e/ML330 Server Maintenance and Service Guide specifications CD-ROM drive access times 5-4 capacity 5-4 data transfer rate 5-4 dimensions 5-4 laser parameters 5-5 operating conditions 5-5 rotational speed 5-4 startup time 5-4 stop time 5-4 weight 5-4 diskette drive access times 5-3 data transfer rate 5-3 height 5-3 number supported 5-3 read/write heads 5-3 size 5-3 hard drives capacity 5-5, 5-6 data transfer rate 5-5, 5-6 interface type 5-5, 5-6 physical configuration 5-5, 5-6 seek t
Index Integrated Single-Channel Wide Ultra2 SCSI Controller Specifications 5-7 Integrated Ultra ATA 100 Controller Specifications 5-8 Mechanical Spare Parts List 1-3 Memory Module Socket Locations 2-24 Memory Specifications 5-3 Network Controller LEDs 4-12 Rear Panel Connectors 4-4 Reserved Processor Switch Settings (SW1) 4-7 Server Feature Board Components (ProLiant ML330 Server) 4-6 Server Feature Board Components (ProLiant ML330e Server) 4-5 Server Feature Board Switch Settings (SW1) 4-9 Storage Device
