HP ProLiant MicroServer Gen8 User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Contents Component identification ............................................................................................................... 6 Front panel components ............................................................................................................................. 6 Front panel LEDs and buttons ...................................................................................................................... 7 Rear panel components .........................................
Drive installation guidelines ............................................................................................................ 43 Installing a non-hot-plug drive .......................................................................................................... 43 Controller options .................................................................................................................................... 45 Installing a storage controller .........................................
Keeping the system current ....................................................................................................................... 75 Drivers ......................................................................................................................................... 75 Software and firmware ................................................................................................................... 76 Version control ........................................................
Component identification Front panel components Item Description 1 USB 2.
Front panel LEDs and buttons Item Description Status 1 Power On/Standby button and system power LED Solid green = System on Flashing green (1 Hz/cycle per sec) = Performing power on sequence Solid amber = System in standby Off = No power present* 2 NIC status LED Solid green = Link to network Flashing green (1 Hz/cycle per sec) = Network active Off = No network activity 3 Drive status LED Solid green = System on Flashing green = Drive activity Off = System in standby or no power present 4 Heal
Rear panel components Item Description 1 Kensington security slot 2 Power supply 3 Serial number/iLO information tag* 4 Power cord connector 5 Dedicated iLO 4 connector 6 Video connector 7 USB 3.0 connectors 8 USB 2.0 connectors 9 NIC connector 2 10 NIC connector 1/shared iLO 4 connector 11 System fan * The serial number/iLO information tag shows the server serial number and the default iLO account information.
Rear panel LEDs and buttons Item Description Status 1 NIC link LED Solid green = Link exists Off = No link exists 2 NIC status LED Solid green = Link to network Flashing green (1 Hz/cycle per sec) = Network active Off = No network activity System board components Component identification 9
Item Description 1 Fan connector 2 DIMM slots 3 Front I/O connector 4 Processor socket 5 TPM connector 6 System battery 7 Mini-SAS connector 8 Optical drive SATA connector 9 Ambient temperature sensor connector 10 24-pin system board power connector 11 Internal USB 2.
DIMM slot locations DIMM slots are numbered sequentially (1 through 4) for the processor. The supported AMP modes use the letter assignments for population guidelines. System maintenance switch Position Default Function S1 Off Off = iLO 4 security is enabled. On = iLO 4 security is disabled. S2 Off Off = System configuration can be changed. On = System configuration is locked. S3 Off Reserved S4 Off Reserved S5 Off Off = Power-on password is enabled. On = Power-on password is disabled.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to properly configure the server or data loss could occur. NMI functionality An NMI crash dump creates a crash dump log before resetting a system which is not responding. Crash dump log analysis is an essential part of diagnosing reliability problems, such as failures of operating systems, device drivers, and applications. Many crashes freeze a system, and the only available action for administrators is to restart the system.
FBWC module LED definitions The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicated on the reverse side of the cache module to facilitate status viewing. 1 - Amber 2 - Green 3 - Green Interpretation Off Off Off The cache module is not powered. Off Flashing 0.5 Hz Flashing 0.5 Hz The cache microcontroller is executing from within its boot loader and receiving new flash code from the host controller.
Fan location The server has one system fan located at the rear of the server. T-10/T-15 Torx screwdriver The server includes a T-10/T-15 Torx screwdriver located on the front panel. Use this screwdriver to loosen screws during hardware configuration procedures.
Operations Power up the server 1. Connect the power cord to the server ("Connecting the power cord" on page 28). 2. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green. Power down the server Before powering down the server for any upgrade or maintenance procedures, perform a backup of critical server data and programs.
• Press and hold the Power On/Standby button for more than 4 seconds to force the server to enter standby mode. This method forces the server to enter standby mode without properly exiting applications and the OS. If an application stops responding, you can use this method to force a shutdown. • Use a virtual power button selection through iLO 4. This method initiates a controlled remote shutdown of applications and the OS before the server enters standby mode.
5. Slide the release tab upward to unlock the front bezel from the chassis. 6. Open the front bezel. Remove the front bezel 1. Open the front bezel (on page 16).
2. Release the bezel hinges from the front panel. Install the front bezel 1. If the chassis cover was removed, install it ("Install the chassis cover" on page 19). 2. Attach the bezel to the front panel, and then close it. 3. If the chassis cover was removed, do the following: a. Connect the power cord to the server ("Connecting the power cord" on page 28). b. Press the Power On/Standby button. The server exits standby mode and applies full power to the system.
Remove the chassis cover 1. Power down the server (on page 15). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Disconnect all peripheral cables from the server. 5. If a Kensington security cable is installed, disconnect it from the rear panel. See the security cable documentation for instructions. 6. Loosen the rear thumbscrews that secure the chassis cover. 7.
2. Tighten the rear thumbscrews to secure the chassis cover in place. 3. Connect the peripheral devices to the server ("Connecting peripheral devices" on page 26). 4. If a Kensington security cable was removed, connect it to the rear panel. See the security cable documentation for instructions. 5. Connect the server to the network. Do one of the following: o Connect the Ethernet cable ("Connecting the Ethernet cable" on page 26).
In the following illustration of the system board, the gray connectors correspond to the system board cables that you must disconnect. 8. Press the system board tray latch.
9. Slide the system board assembly completely out of the chassis. Install the system board assembly 1. Slide the system board assembly into the chassis. 2. Connect all cables disconnected from the system board and/or expansion board.
Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs.
Temperature requirements To ensure continued, safe, and reliable equipment operation, install or position the system in a well-ventilated, climate-controlled environment. The maximum recommended TMRA for most server products is 35°C (95°F). The temperature in the room where the server is located must not exceed 35°C (95°F).
Server warnings and cautions WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed.
Connecting peripheral devices The I/O connectors are color coded and are marked with icons. The server has seven USB connectors: • Four external USB 2.0 • Two external rear USB 3.0 • One internal USB 2.0 connector on the system board connectors, two each on the front and rear panels connectors IMPORTANT: When running the Microsoft Windows Server 2008 SP2 (x86 and x86-64 editions) or the Microsoft Windows Server 2008 R2 SP1 operating systems, native USB 3.0 support is not available.
• Dedicated iLO connector To connect an Ethernet cable: 1. Connect one end of the Ethernet cable to the NIC 1 connector. 2. Connect the other end of the Ethernet cable to a network jack.
Connecting the power cord WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. • Unplug the power cord from the power supply to disconnect power to the equipment. • Do not route the power cord where it can be walked on or pinched by items placed against it.
Powering on and selecting boot options 1. Press the Power On/Standby button. 2. Check the server Power LED status is established. 3. During the initial server boot (POST), do one of the following: . The LED flashes green to indicate that the AC power connection o For advanced users, to modify the server configuration ROM default settings, press F9 when prompted to enter the RBSU. By default, the RBSU runs in the English language.
Performing the initial system setup HP recommends using Intelligent Provisioning to install the server operating system. All firmware, drivers, and tools required by the system are installed during the same process. Intelligent Provisioning provides installation help for the following operating systems: Microsoft Windows, Red Hat and SUSE Linux, and VMware.
3. Click Create Array.
4. Select the check box next to the drives to include in the RAID logical drive, and then click OK.
5. The new drive array is listed on the left side of the screen. Select the drive array, and then click Create Logical Drive. 6. The system determines the optimum RAID configuration settings based on the number of drives selected. To retain these settings, click Save. For advanced users, to modify these default settings, see the Configuring Arrays on HP Smart Array Controllers Reference Guide on the HP website (http://www.hp.com/support/CASAC_RG_en). 7. Click Exit ACU. 8. Click PREVIOUS .
Complete the system setup Check the status of the server LEDs to ensure that the server is operating normally: • System power LED • NIC status LED —Solid green • Drive status LED —Solid green • Health LED bar—Solid blue —Solid green For server management tasks after the initial server setup, use either the dedicated iLO connector (enabled by default) or the NIC 1/shared iLO connector (It is disabled by default. Enable the shared iLO function in iLO RBSU).
Mount the switch with the server 1. Attach the self-adhesive rubber pads to the bottom surface of the switch. 2. Stack the switch with the server: CAUTION: The switch has a limitation on how much weight can be placed on top of it. To reduce the risk of personal injury or damage to the equipment because of an unstable server-switch stacking, stack no more than two servers on top of the switch. o Top stacking—Stack the server on top of the switch.
o Bottom stacking—Stack the switch on the top of the server. You can stack up to three MicroServers. Complete the switch Self-Test 1. Connect an Ethernet cable to the switch, and then connect the cable to a network jack. 2. If you are using a wall-mount power adapter, do the following: a. Connect the power adapter to the switch.
b. Connect the power adapter to the AC power source. 3. If you are using an in-line power adapter, do the following: a. Connect the power adapter to the switch. b. Connect the power cord to the adapter. c. Connect the power cord to the AC power source. 4. Check the status of the switch Power LED. This LED is solid green to indicate that the power connection is established. 5.
To establish a simple Ethernet connection: 1. Connect an Ethernet cable to the server NIC connector 1 or 2. 2. Connect the cable to any switch network port. To establish an Ethernet connection with iLO functionality by using the dedicated iLO connector: 1. Connect an Ethernet cable to the server NIC connector 1 or 2. 2. Connect the cable to any switch network port. 3. Connect an Ethernet cable to the server dedicated iLO connector, and then connect the cable to any switch network port.
2. Under the Network menu, select the NIC and TCP/IP option. 3. Set the Network Interface Adapter field to Shared Network Port — LOM. 4. To save the change, press F10. 5. To close the iLO RBSU, under the File menu, select the Exit option.
6. Connect an Ethernet cable to the server NIC 1/shared iLO connector, and then connect the cable to any switch network port.
Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure.
6. Separate the bezel faceplate from the bezel frame. Store the removed bezel faceplate for future use. 7. Install the preferred bezel faceplate to the bezel frame, and then secure the assembly with the screws removed in the previous step. Spare screws are also included in the option kit. 8. Install the front bezel, and then close it.
If the chassis cover was removed during preinstallation, you can secure the bezel to the chassis by sliding the release tab downward. 9. If the chassis cover was removed, do the following: a. Install the chassis cover (on page 19). b. Connect the power cord to the server ("Connecting the power cord" on page 28). c. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green.
To install the component: 1. Power down the server (on page 15). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Open the front bezel (on page 16). 5. Remove the drive carrier. 6. Remove the two metal brackets from the drive carrier. 7. Install the drive in the carrier.
8. Install the drive. 9. Close the front bezel. 10. If the chassis cover was removed, do the following: a. Install the chassis cover (on page 19). b. Connect the power cord to the server ("Connecting the power cord" on page 28). c. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green.
CAUTION: To prevent a server malfunction or damage to the equipment, do not add or remove the capacitor pack while an array capacity expansion, RAID level migration, or stripe size migration is in progress. CAUTION: After the server is powered down, wait for 30 seconds, and then check the amber LED before unplugging the cable from the cache module. If the amber LED flashes after 30 seconds, do not remove the cable from the cache module. The cache module is backing up data.
For more information about the controller and its features, see the HP Smart Array Controllers for HP ProLiant Servers User Guide on the HP website (http://www.hp.com/support/SAC_UG_ProLiantServers_en). To configure arrays, see the Configuring Arrays on HP Smart Array Controllers Reference Guide on the HP website (http://www.hp.com/support/CASAC_RG_en).
d. Route the capacitor pack cable through the internal left side chassis opening down to the system board. 8. Connect the capacitor pack cable to the cache module. 9. Secure the capacitor pack cable in the designated cable management clips: a. Secure the cable in the two rear side cable clips. b. Secure the cable in the internal left side chassis cable clip.
c. Secure the excess length of the cable in the top chassis cable clip. 10. Install the chassis cover (on page 19). 11. Connect the power cord to the server ("Connecting the power cord" on page 28). 12. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green.
5. Press the optical drive blank release latches, and then pull the blank out of the drive bay. Retain the blank for future use. 6. Install the optical drive into the bay. 7. Connect the optical drive SATA Y-cable: a. Connect the common end of the Y-cable to the optical drive. b. Connect the power end of the Y-cable to the power supply cable labeled P3. c. Route the data end of the Y-cable through the left side chassis opening down to the system board. d.
For cable routing information, see "Optical drive cabling (on page 62)." 8. Secure the optical drive SATA cable in the designated cable management clips: a. Secure the excess cable in the top chassis cable clip. b. Secure the cable in the internal left side chassis cable clip. 9. Install the chassis cover (on page 19). 10. Connect the power cord to the server ("Connecting the power cord" on page 28). 11. Press the Power On/Standby button.
Memory options The server memory subsystem supports UDIMMs only. UDIMMs represent the most basic type of memory module and offer lower latency and (relatively) low power consumption, but are limited in capacity. The server supports dual-rank, PC3-10600E/PC3-12800E (DDR3 ECC) DIMMs operating at 1333 MHz or 1600 MHz speed. Memory speed depends on the type of processor and the number of DIMMs installed in the server. Installed DIMMs can operate at either 1600 MT/s or 1333 MT/s.
Item Description Definition 3 Data width x4 = 4-bit x8 = 8-bit 4 Voltage rating L = Low voltage (1.35V) U = Ultra low voltage (1.25V) Blank or omitted = Standard 5 Memory speed 12800 = 1600-MT/s 10600 = 1333-MT/s 8500 = 1066-MT/s 6 DIMM type R = RDIMM (registered) E = UDIMM (unbuffered with ECC) L = LRDIMM (load reduced) For the latest supported memory information, see the QuickSpecs on the HP website (http://h18000.www1.hp.com/products/quickspecs/ProductBulletin.html).
General DIMM slot population guidelines • The server supports a maximum of 16 GB memory using two 8 GB single-rank or dual-rank UDIMMs. • The server supports up to 1600 MT/s ECC UDIMMs. • LV DIMMs operate at 1.35 V instead of the 1.5 V for standard DDR3 DIMMs. LV DIMMs can be installed in this server, but the system does not recognize the reduced power consumption feature. It will be treated as a standard DDR3 DIMM.
6. Align the notch on the bottom edge of the memory module with the keyed surface of the DIMM slot, and then fully press the memory module into the slot until the latches snap back into place. 7. Install the chassis cover (on page 19). 8. Connect the power cord to the server ("Connecting the power cord" on page 28). 9. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green. 10.
7. For added board stability, remove the screw located underneath the slot cover retainer latch, and then use it to secure the expansion board. 8. Verify that any switches or jumpers on the expansion board are set properly. For more information, see the documentation that ships with the option. 9. Install the expansion board. Verify that the board is firmly seated in the slot. 10. For added board stability, use the screw removed in step 7 to secure the board. 11.
16. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green. HP Trusted Platform Module option For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the HP Product Bulletin website (http://www.hp.com/go/productbulletin). Use these instructions to install and enable a TPM on a supported server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. 1. Power down the server (on page 15). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Remove the chassis cover (on page 19). 5. Remove the system board assembly (on page 20). CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security rivet.
8. Install the system board assembly (on page 22). 9. Connect the power cord to the server ("Connecting the power cord" on page 28). 10. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green. Retaining the recovery key/password The recovery key/password is generated during BitLocker™ setup, and can be saved and printed after BitLocker™ is enabled.
Cabling Cabling overview This section provides guidelines that help you make informed decisions about cabling the server and hardware options to optimize performance. For information on cabling peripheral components, refer to the white paper on high-density deployment at the HP website (http://www.hp.com/products/servers/platforms). CAUTION: When routing cables, always be sure that the cables are not in a position where they can be pinched or crimped.
• Mini-SAS cable connected to controller board Item Description 1 4-pin power cable (connected to the PSU P2 cable) 2 Mini-SAS cable Capacitor pack cabling Cabling 61
Optical drive cabling Item Description 1 4-pin power connector (connected to the PSU P3 cable) of the optical drive SATA Y-cable 2 Common end of the optical drive SATA Y-cable 3 SATA connector of the optical drive SATA Y-cable Front I/O assembly cabling Cabling 62
Ambient temperature sensor cabling System fan cabling Cabling 63
Power supply cabling Item PSU cable marker Description 1 P3 4-pin optical drive power cable 2 P2 4-pin drive power cable 3 P1 24-pin system board power cable Cabling 64
Software and configuration utilities Server mode The software and configuration utilities presented in this section operate in online mode, offline mode, or in both modes.
iLO 4 enables and manages the Active Health System (on page 66) and also features Agentless Management. All key internal subsystems are monitored by iLO 4. SNMP alerts are sent directly by iLO 4 regardless of the host operating system or even if no host operating system is installed. HP Insight Remote Support software (on page 69) is also available in HP iLO with no operating system software, drivers, or agents.
The data that is collected is managed according to the HP Data Privacy policy. For more information see the HP website (http://www.hp.com/go/privacy). The Active Health System log, in conjunction with the system monitoring provided by Agentless Management or SNMP Pass-thru, provides continuous monitoring of hardware and configuration changes, system status, and service alerts for various server components. The Agentless Management Service is available in the SPP, which is a disk image (.
HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server installations, troubleshoot problems, and perform repair validation. HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the OS is not running. To run this utility, boot the server using Intelligent Provisioning (on page 67).
HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support software to complete the installation or upgrade of your product and to enable enhanced delivery of your HP Warranty, HP Care Pack Service, or HP contractual support agreement.
DL, and SL servers. The toolkit includes a modular set of utilities and important documentation that describes how to apply these tools to build an automated server deployment process. The Scripting Toolkit provides a flexible way to create standard server configuration scripts. These scripts are used to automate many of the manual steps in the server configuration process.
For more information about HP SUM and to access the HP Smart Update Manager User Guide, see the HP website (http://www.hp.com/go/hpsum/documentation).
NOTE: The server may not support all the following examples. Drives installed Drives used RAID level 1 1 RAID 0 2 2 RAID 1 3, 4, 5, or 6 3, 4, 5, or 6 RAID 5 More than 6 0 None To change any ORCA default settings and override the auto-configuration process, press the F8 key when prompted. For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website (http://www.hp.com/support/rbsu).
Utilities and features Array Configuration Utility ACU is a utility with the following features: • Runs as a local application or remote service accessed through the HP System Management Homepage • Supports online array capacity expansion, logical drive extension, assignment of online spares, and RAID or stripe size migration • Suggests the optimum configuration for an unconfigured system • For supported controllers, provides access to licensed features, including: o Moving and deleting individual
Option ROM Configuration for Arrays Before installing an operating system, you can use the ORCA utility to create the first logical drive, assign RAID levels, and establish online spare configurations.
Before the OS loads, HP provides support for USB 2.0 devices through legacy USB support, which is enabled by default in the system ROM. USB 3.0 ports are not functional before the OS loads. The native OS provides USB 3.0 support through appropriate xHCI drivers. Legacy USB support provides USB functionality in environments where USB support is not available normally.
To locate the drivers for a particular server, go to the HP website (http://www.hp.com/go/hpsc) and click on Drivers, Software & Firmware. Then, enter your product name in the Find an HP product field and click Go. Software and firmware Software and firmware should be updated before using the server for the first time, unless any installed software or components require an older version.
HP Support Center—For all service options, the HP Support Center delivers the information, tools, and experts required to support HP business products. HP Insight Remote Support—Provides 24x7 secure remote monitoring, diagnosis, and problem resolution. For more information, see one of the following websites: • HP ProLiant Server Services website (http://www.hp.com/services/proliant) • HP BladeSystem Services website (http://www.hp.
Troubleshooting Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, issue resolution, and software maintenance on ProLiant servers and server blades. To view the guide, select a language: • English (http://www.hp.com/support/ProLiant_TSG_v1_en) • French (http://www.hp.com/support/ProLiant_TSG_v1_fr) • Spanish (http://www.hp.
System battery replacement If the server no longer automatically displays the correct date and time, then replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • • • • Do not attempt to recharge the battery.
Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the HP website (http://www.hp.com/support/Safety-Compliance-EnterpriseProducts). Belarus Kazakhstan Russia marking Turkey RoHS material content declaration Ukraine RoHS material content declaration Warranty information HP ProLiant and X86 Servers and Options (http://www.hp.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Nonoperating -30°C to 60°C (-22°F to 140°F) Relative humidity (noncondensing) Operating, maximum wet bulb 10% to 90% temperature of 28°C (82.4°F) Nonoperating, maximum wet 5% to 95% bulb temperature of 38.7°C (101.7°F) * All temperature ratings shown are for sea level. An altitude derating of 1°C per 304.8 m (1.8°F per 1,000 ft) to 3048 m (10,000 ft) is applicable.
HP 150 W Integrated Power Supply Specification Value Input requirements — Rated input voltage 100 V AC to 240 V AC Rated input frequency 47 Hz to 63 Hz Rated input current 3.
Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log (HP ProLiant Gen8 or later products) Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça.
Support and other resources 90
Support and other resources 91
Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ADM Advanced Data Mirroring AMP Advanced Memory Protection ASR Automatic Server Recovery CSA Canadian Standards Association CSR Customer Self Repair DDR3 double data rate-3 EAC EuroAsian Economic Commission FBWC flash-backed write cache HP SIM HP Systems Insight Manager HP SUM HP Smart Update Manager Acronyms and abbreviations 92
IEC International Electrotechnical Commission iLO Integrated Lights-Out IML Integrated Management Log IRS Insight Remote Support ISO International Organization for Standardization LFF large form factor LOM Lights-Out Management LRDIMM load reduced dual in-line memory module LV DIMM low-voltage DIMM NMI nonmaskable interrupt NVRAM nonvolatile memory OA Onboard Administrator ORCA Option ROM Configuration for Arrays PCIe Peripheral Component Interconnect Express Acronyms and abbreviations 93
PDU power distribution unit POST Power-On Self Test PSU power supply unit PXE preboot execution environment RBSU ROM-Based Setup Utility RDIMM registered dual in-line memory module RDP Rapid Deployment Pack RoHS Restriction of Hazardous Substances SAS serial attached SCSI SATA serial ATA SD Secure Digital SPP HP Service Pack for ProLiant TMRA recommended ambient operating temperature TPM Trusted Platform Module Acronyms and abbreviations 94
UDIMM unregistered dual in-line memory module USB universal serial bus VC Virtual Connect VCA Version Control Agent VCRM Version Control Repository Manager Acronyms and abbreviations 95
Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Index A D ambient temperature sensor, cabling 63 Array Configuration Utility (ACU) 73 array, configuring 45 array, creating 73 authorized reseller 84 auto-configuration process 71 Automatic Server Recovery (ASR) 74 diagnostic tools 65, 68, 74 dimensions and weight 82 DIMM identification 52 DIMM population guidelines 54 DIMM slot locations 11 DIMMs, installing 54 DIMMs, single- and dual-rank 53 documentation feedback 96 drive cabling 60 drive LEDs 7 drive numbering 12 driver installation procedures 75 dri
G M grounding methods 81 grounding requirements 24 maintenance guidelines 75 memory dump 12 memory module population guidelines 54 memory options 52 memory subsystem architecture 53 microSD card slot 9 H hardware options installation 41 health driver 74 health LED 7 help resources 84 HP Care Pack Services 23, 76 HP Collaborative Support 76 HP contact information 84 HP Insight Diagnostics 68 HP Insight Remote Support software 69, 76 HP Proactive Care 76 HP Service Pack for ProLiant 65, 70 HP Smart Update
R RAID configuration 45 Rapid Deployment Pack (RDP) 23 rear panel buttons 9 rear panel components 8 rear panel LEDs 9 redundant ROM 75 re-entering the server serial number 72 registering the product 34 regulatory compliance notices 80 required tools 25 requirements, airflow 23 requirements, electrical grounding 24 requirements, environmental 23, 82 requirements, power 24 requirements, site 23 requirements, space 23 requirements, temperature 24 RoHS 80 ROM legacy USB support 74 ROM redundancy 75 ROM-Based Se
