Maintenance and Service Guide HP Compaq nc6400 Notebook PC Document Part Number: 406847-003 March 2007 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures.
© Copyright 2006, 2007 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States or other countries. Intel, Celeron, and Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor.
Safety warning notice Å WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Contents 1 Product Description 1.1 1.2 1.3 1.4 1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–4 Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Design Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 1–24 2 Troubleshooting 2.1 Starting Computer Setup . . . . . . . . . . . . . . . . . . . .
Contents 3 Illustrated Parts Catalog 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1 Computer Major Components. . . . . . . . . . . . . . . . . . 3–2 Display Assembly Components . . . . . . . . . . . . . . . 3–16 Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–18 Cable Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–19 Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . .
Contents 5 Removal and Replacement Procedures 5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2 5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–3 5.3 Preparing the Computer for Disassembly . . . . . . . . . 5–5 5.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7 5.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11 5.6 Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12 5.
Contents 6 Specifications A Screw Listing B Backup and Recovery in Windows Vista C Backup and Recovery in Windows XP D Display Component Recycling E Connector Pin Assignments F Power Cord Set Requirements Index vii Maintenance and Service Guide
1 Product Description The HP Compaq nc6400 Notebook PC offers advanced modularity, Intel® Core™ Duo, Core Solo, and Celeron® processors, and extensive multimedia support.
Product Description 1.1 Features ■ The following processors, varying by computer model: ❏ Intel Core Duo T7600 (2.33-GHz) processor ❏ Intel Core Duo T7400 (2.16-GHz) processor ❏ Intel Core Duo T7200 (2.00-GHz) processor ❏ Intel Core Duo T5600 (1.83-GHz) processor ❏ Intel Core Duo T5500 (1.66-GHz) processor ❏ Intel Core Duo T2300E (1.66-GHz) processor ❏ Intel Core Duo T2600 (2.17-GHz) processor ❏ Intel Core Duo T2500 (2.00-GHz) processor ❏ Intel Core Duo T2400 (1.
Product Description ■ ■ ■ ■ ■ ■ ■ ■ ■ Integrated high-speed 56K modem with RJ-11 jack Integrated wireless support for Mini Card IEEE 802.11a/b/g or 802.
Product Description 1.2 Resetting the Computer If the computer you are servicing has an unknown password, follow the steps below to reset the password. These steps also clear CMOS. following steps will not clear an unknown password if the ✎ The stringent security option has been enabled in the BIOS. If stringent security is enabled, the system board must be replaced to reset an unknown password. Refer to Section 5.21, “Top Cover,” for more information on replacing the system board.
Product Description 1.3 Power Management The computer comes with power management features that extend battery operating time and conserve power.
Product Description 1.4 External Components The external components on the front of the computer are shown below and described in Table 1-1. Front Components Table 1-1 Front Components Item Component Function 1 Wireless light On: An integrated wireless device, such as a wireless local area network (LAN) device and/or a Bluetooth® device, is turned on. 2 Power light ■ On: The computer is on. ■ Blinking: The computer is in standby.
Product Description Table 1-1 Front Components (Continued) Item Component Function 3 Battery light ■ Amber: A battery is charging. ■ Green: A battery is close to full charge capacity. ■ Blinking amber: A battery that is the only available power source has reached a low-battery condition. When the battery reaches a critical low-battery condition, the battery light begins blinking more quickly.
Product Description The external components on the right side of the computer are shown below and described in Table 1-2.
Product Description Table 1-2 Right-Side Components Item Component Function 1 Smart card slot Supports optional smart cards and Java™ Cards. 2 MultiBay II device Supports an optical disc. The type of optical drive varies by computer model. 3 USB port Connects USB 1.1- and 2.0-compliant devices to the computer using a standard USB cable, or connects an optional External MultiBay II to the computer. The MultiBay II must also be connected to an external power source.
Product Description The external components on the left side of the computer are shown below and described in Table 1-3.
Product Description Table 1-3 Left-Side Components Item Component Function 1 Exhaust vent Provides airflow to cool internal components. 2 USB ports (2) Connect USB 1.1- and 2.0-compliant devices to the computer using a standard USB cable, or connect an optional External MultiBay II to the computer. The MultiBay II must also be connected to an external power source. 3 Audio-in (microphone) jack Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Product Description The external components on the rear panel of the computer are shown below and described in Table 1-4.
Product Description Table 1-4 Rear Panel Components Item Component Function 1 Security cable slot Attaches an optional security cable to the computer. Ä Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. 2 Battery bay Holds a battery. 3 Smart adapter power connector Connects an AC adapter or an optional power adapter.
Product Description The standard keyboard components of the computer are shown below and described in Table 1-5.
Product Description Table 1-5 Standard Keyboard Components Item Component Function 1 fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 f1 to f12 keys (12) Perform system and application tasks. When combined with the fn key, several keys and buttons perform additional tasks as hotkeys.
Product Description The computer top components are shown below and described in Table 1-6.
Product Description Table 1-6 Top Components Item Component Function 1 Power button When the computer is: ■ Off, press to turn on the computer. ■ On, briefly press to initiate hibernation. ■ In standby, briefly press to resume from standby. ■ In hibernation, briefly press to restore from hibernation. If the system has stopped responding and Windows shutdown procedures cannot be used, press and hold for 5 seconds to turn off the computer.
Product Description The computer top components are shown below and described in Table 1-7.
Product Description Table 1-7 Top Components Item Component Function 1 Power light ■ On: The computer is on. ■ Blinking: The computer is in standby. ■ Blinking rapidly: An AC adapter with a higher power rating should be connected. ■ Off: The computer is off or in hibernation. 2 Wireless light On: An integrated wireless device, such as a wireless local area network (LAN) device and/or a Bluetooth® device, is turned on. 3 Caps lock light On: caps lock is on.
Product Description The computer pointing device components are shown below and described in Table 1-8.
Product Description Table 1-8 Pointing Device Components Item Component Function 1 Pointing stick Moves the pointer and selects or activates items on the screen. 2 Pointing stick buttons Function like the left, middle, and right buttons on an external mouse. 3 TouchPad Moves the pointer and selects or activates items on the screen. Can be set to perform other mouse functions, such as scrolling, selecting, and double-clicking.
Product Description The external components on the bottom of the computer are shown below and described in Table 1-9. Bottom Components Table 1-9 Bottom Components Item Component Function 1 Battery bay Holds the battery. 2 Docking connector (full-featured models only) Connects the computer to an optional docking device. 3 Battery release latches (2) Release the battery from the battery bay.
Product Description Table 1-9 Bottom Components (Continued) Item Component Function 5 Exhaust vents Provides airflow to cool internal components. 6 Hard drive bay Holds the primary hard drive. 7 Memory module compartment Contains one memory slot that supports replaceable memory modules. 8 Bluetooth compartment Contains a Bluetooth device (select computer models only). 9 Serial number Identifies the computer. This number is needed when contacting customer support.
Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.
2 Troubleshooting Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting To start Computer Setup: 1. Turn on or restart the computer. 2. Before Windows® opens and while the “F10=ROM Based Setup” message is displayed in the lower-left corner of the screen, press f10. Using Computer Setup Navigating and selecting in Computer Setup The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System Configuration menus. 1.
Troubleshooting 3. To exit Computer Setup, choose one of the following methods: ❏ To exit Computer Setup without saving your preferences, use the arrow keys to select File > Ignore Changes and Exit. Then follow the instructions on the screen. ❏ To save your preferences and exit Computer Setup, use the arrow keys to select File > Save Changes and Exit. Then follow the instructions on the screen. Your preferences go into effect when the computer restarts.
Troubleshooting Computer Setup Menus The menu tables in this section provide an overview of Computer Setup options. of the Computer Setup menu items listed in this chapter ✎ Some may not be supported by your computer. File Menu Table 2-1 File Menu Select To do this System Information ■ View identification information for the computer and the batteries in the system. ■ View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version.
Troubleshooting Security Menu Table 2-2 Security Menu Select To do this Setup password Enter, change, or delete a setup password. Power-On password Enter, change, or delete a power-on password. Password options ■ Enable/disable stringent security. ■ Enable/disable password requirement on computer restart. DriveLock passwords ■ Enable/disable DriveLock on any computer hard drive and on optional MultiBay hard drives. ■ Change a DriveLock user password or master password.
Troubleshooting Table 2-2 Security Menu (Continued) Select To do this TPM Embedded Security Enable/disable support for TPM (Trusted Platform Module) Embedded Security, which protects the computer from unauthorized access to owner functions available in Embedded Security for ProtectTools. For more information, refer to the ProtectTools online Help. must have a setup password to change ✎ You this setting. System IDs Enter user-defined computer asset and ownership tag.
Troubleshooting Diagnostics Menu Table 2-3 Diagnostics Menu Select To do this Hard Drive Self-Test options Run a comprehensive self-test on any hard drive in the system or on any optional MultiBay hard drive. Memory Check Run a comprehensive check on system memory. Startup Check (select models only) Verify the system components needed for starting the computer. System Configuration Menu of the listed System Configuration options may not be ✎ Some supported by your computer.
Troubleshooting Table 2-4 System Configuration Menu (Continued) Select To do this Device Configurations ■ Swap the functions of the fn key and left ctrl key. ■ Enable/disable multiple standard pointing devices at startup. (To set the computer to support only a single, usually nonstandard, pointing device at startup, select Disable.) ■ Enable/disable USB legacy support.
Troubleshooting Table 2-4 System Configuration Menu (Continued) Select To do this Device configurations (continued) ■ Choose Bit-shift or LBA assisted HDD Translation Mode. ■ Enable/disable Windows direct application launcher. ■ Enable/disable HP Lockout. Built-In Device Options ■ Enable/disable embedded WWAN Device Radio. ■ Enable/disable embedded WLAN Device Radio ■ Enable/disable embedded Bluetooth® Device Radio. ■ Enable/disable LAN/WLAN Switching.
Troubleshooting 2.2 Troubleshooting Flowcharts Table 2-5 Troubleshooting Flowcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial Troubleshooting” 2.2 “Flowchart 2.2—No Power, Part 1” 2.3 “Flowchart 2.3—No Power, Part 2” 2.4 “Flowchart 2.4—No Power, Part 3” 2.5 “Flowchart 2.5—No Power, Part 4” 2.6 “Flowchart 2.6—No Video, Part 1” 2.7 “Flowchart 2.7—No Video, Part 2” 2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)” 2.9 “Flowchart 2.
Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. N Go to Is there power? “Flowchart 2.2—No Power, Part 1.” Y N Check LED board, speaker connections. Beeps, LEDs, or error messages? N Y Go to All drives working? N Go to Is there video? (no boot) Y “Flowchart 2.6—No Video, Part 1.” N Keyboard/ pointing device working? Y N Go to Is the OS loading? N Go to Is there sound? Y “Flowchart 2.9—No Operating System (OS) Loading.” Y “Flowchart 2.15—No Audio, Part 1.
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). N N Power up on battery power? Go to Power up on battery power? Reset power.* “Flowchart 2.3—No Power, Part 2.” Y Y N N Power up on AC power? Power up on AC power? Reset power.* Go to “Flowchart 2.4—No Power, Part 3.” Y Y Y Power up in docking device? Done *NOTES N 1. Reset the power cables in the docking device and at the AC outlet. 2.
Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Y Power on? Done N Check battery by recharging it, moving it to another computer, or replacing it. N Replace power supply (if applicable). Power on? Y N Go to Done Power on? “Flowchart 2.4—No Power, Part 3.
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Y Power LED on? Done N Reseat AC adapter in computer and at power source. Y Power on? Done N External N Try different outlet. Power outlet active? Y Internal or external AC adapter? Replace external AC adapter. N Internal Go to “Flowchart 2.5—No Power, Part 4.” Replace power cord.
Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open computer. Y Loose or damaged parts? N Reseat loose components and boards and replace damaged items. Close computer and retest. N Power on? Replace the following items (if applicable). Check computer operation after each replacement: 1. Internal DC-DC converter* 2. Internal AC adapter 3. Processor board* 4. System board* *NOTE: Replace these items as a set to prevent shorting out among components.
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Go to Stand-alone or docking device? *NOTE: To change from internal to external display, use the hotkey combination. “Flowchart 2.7—No Video, Part 2.” Stand-alone Internal or external display*? Y Adjust brightness. A Adjust brightness. Press lid switch to ensure operation. Y Video OK? Done N Internal External Video OK? Y Done N Video OK? Done N Replace the following one at a time. Test after each replacement. 1.
Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove computer from docking device, if connected. Adjust display brightness. Check brightness of external monitor. N Y Go to “A” in “Flowchart 2.6—No Video, Part 1.” Video OK? Y Video OK? Done N Check that computer is properly seated in docking device, for bent pins on cable, and for monitor connection. Try another external monitor.
Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reset power cord in docking device and power outlet. Check voltage setting on docking device. Reset monitor cable connector at docking device. Reinstall computer into docking device. Y Docking device operating? N Y Docking device operating? Done Done N Replace docking device. 2–18 Test replacement docking device with new computer.
Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reset power cord in docking device and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.” No OS loading from CD-ROM or DVD-ROM drive, go to “Flowchart 2.14—No OS Loading, Optical Drive.” No OS loading from network, go to “Flowchart 2.20—No Network/Modem Connection.
Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Y Nonsystem disk message? N Go to “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” Reseat external hard drive. Y OS loading? Done N N Boot from CD? N Y Boot from diskette? Check the Setup utility for correct booting order. Y Change boot priority through the Setup Utility and reboot. N Boot from hard drive? N Y Boot from hard drive? Done Y 2–20 Go to “Flowchart 2.
Troubleshooting Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” Reseat hard drive. N 1. Replace hard drive. 2. Replace system board. CD or diskette in drive? Y Hard drive accessible? Y Done N Remove diskette and reboot. Run FDISK. Y Boot from hard drive? N Done N Hard drive partitioned? Y N Y N Go to “Flowchart 2.13—No OS Loading, Diskette Drive.
Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” N System files on hard drive? Install OS and reboot. Y Y Y Virus on hard drive? OS loading from hard drive? Clean virus. N Done N Y Run SCANDISK and check for bad sectors. Diagnostics on diskette? Replace hard drive. N N Can bad sectors be fixed? Run diagnostics and follow recommendations. Replace hard drive. Y N Boot from hard drive? Fix bad sectors.
Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive Y OS not loading from diskette drive. Reseat diskette drive. OS loading? Done N Y N Bootable diskette in drive? Nonsystem disk message? N Y N Check diskette for system files. Try different diskette. Go to Boot from another device? “Flowchart 2.17—Nonfunctioning Device.” Y Y N Diskette drive enabled in the Setup Utility? 1. Replace diskette drive. 2. Replace system board. Nonsystem disk error? Enable drive and cold boot computer.
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive Y No OS loading from CD-ROM or DVD-ROM drive. N Install bootable disc and reboot computer. Bootable disc in drive? Disc in drive? Y N Install bootable disc. Try another bootable disc. Y Boots from CD or DVD? Done N Y Boots from CD or DVD? Reseat drive. Done N N Booting from another device? Y Y Booting order correct? N Go to “Flowchart 2.17—Nonfunctioning Device.” Reset the computer. Refer to Go to Section 1.
Troubleshooting Flowchart 2.15—No Audio, Part 1 Y Turn up audio internally or externally. No audio. Audio? Done N Y Computer in docking device (if applicable)? N Go to Internal audio? Undock N “Flowchart 2.16—No Audio, Part 2.” Y Go to Replace the docking device. “Flowchart 2.16—No Audio, Part 2.” Y Go to “Flowchart 2.17—Nonfunctioning Device.
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” N Audio driver in OS configured? Reload audio drivers. Y N Correct drivers for application? Load drivers and set configuration in OS. Y Connect to external speaker. N Audio? Y Replace audio board and speaker connections in computer (if applicable). Y Audio? Done N 1. Replace internal speakers. 2. Replace audio board (if applicable). 3. Replace system board.
Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or other damage. Y Clear CMOS. Fix or replace broken item. Any physical device detected? N Reattach device. Close computer, plug in power, and reboot. Go to “Flowchart 2.9—No Operating System (OS) Loading.” Replace hard drive. N Device boots properly? N Replace NIC.
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect computer to good external keyboard. N External device works? Replace system board. Y Reseat internal keyboard connector (if applicable). N Replace internal keyboard or cable. OK? Y Y Done OK? Done N Replace system board.
Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect computer to good external pointing device. N Replace system board. External device works? Y Reseat internal pointing device connector (if applicable). N Replace internal pointing device or cable. OK? Y Y Done OK? Done N Replace system board.
Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. N Network or modem jack active? Replace jack or have jack activated. Y Y Connect to nondigital line. Digital line? N Y N NIC/modem configured in OS? Reload drivers and reconfigure. Done OK? N Y Disconnect all power from the computer and open. Replace the NIC/modem (if applicable). Y Reseat NIC/modem (if applicable). OK? Done N Replace system board.
3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and computer model number located on the bottom of the computer.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components Spare Part Number Item Description 1 Display assemblies (include wireless antenna transceivers and cables) 14.1-inch, WXGA+ 14.1-inch, WXGA 418907-001 418896-001 Refer to Section 3.3, “Display Assembly Components,” for display assembly internal component spare part number information.
Illustrated Parts Catalog Computer Major Components 3–4 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description Spare Part Number Cable Kit 418876-001 5a 5b 5c 5d 5e Pointing stick cable TouchPad cable Modem cable Audio cable Bluetooth cable 6 RTC battery 418880-001 7 Microphone 418903-001 8 Top cover Top cover (includes TouchPad, smart card reader, and fingerprint reader board) Top cover (includes TouchPad and smart card reader) 418882-001 Plastics Kit 418877-001 438169-001 9a 9b 9c 9d 9e PC C
Illustrated Parts Catalog Computer Major Components 3–6 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description Spare Part Number 13 Mini Card WWAN module 418860-001 For use with Verizon networks For use with Vodafone networks For use with Cingular networks 418860-001 435098-001 436668-001 14 Fan assembly 418886-001 15 System boards (include thermal grease, alcohol pad, and thermal pad) 16 128-MB discrete, for use only with heat sink with spare part number 418887-001 64-MB discrete, for use only with
Illustrated Parts Catalog Computer Major Components 3–8 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 17 Processors (include thermal grease, alcohol pad, and thermal pad) Intel Core Duo T7600 (2.33-GHz) processor Intel Core Duo T7400 (2.16-GHz) processor Intel Core Duo T7200 (2.0-GHz) processor Intel Core Duo T5600 (1.83-GHz) processor Intel Core Duo T5500 (1.66-GHz) processor Intel Core Duo T2300E (1.66-GHz) processor Intel Core Duo T2600 (2.
Illustrated Parts Catalog Computer Major Components 3–10 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 23 MultiBay II drives (include bezel) DVD±RW and CD-RW Double-Layer Combo Drive DVD±RW and CD-RW Combo Drive DVD-ROM drive 24 Battery 8-cell, 5.1-AH 4-cell, 2.5-AH 25 418866-001 418865-001 418864-001 418867-001 418871-001 Mini Card WLAN modules 802.11b/g HS WLAN module for use in North America 407107-001 802.
Illustrated Parts Catalog Computer Major Components 3–12 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 25 Mini Card WLAN modules (Continued) 802.11a/b/g GL WLAN module for use in the countries or regions listed below. These countries or regions are categorized as most of the world (MOW 1).
Illustrated Parts Catalog Computer Major Components 3–14 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 25 Mini Card WLAN modules (Continued) 802.11a/b/g GL WLAN module for use in the countries or regions listed below. These countries or regions are categorized as the rest of the world (ROW). China Ecuador Haiti 26 Honduras Pakistan Peru Qatar South Korea 407576-003 Uruguay Venezuela 802.11a/b/g GL WLAN module for use in Japan 407576-291 802.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-2 Display Assembly Components Spare Part Number Information Item Description Spare Part Number 1 Display bezel 418889-001 2 Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA 418891-001 418890-001 3 Display Hinge Kit 418902-001 4 Display Inverter 418888-001 5 Wireless Antenna Kit 418899-001 6 Display enclosure 418895-001 Not illustrated: Display Bracket Kit (includes left display bracket) Display Cable Kit (for use with 14.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-6 Miscellaneous (Not Illustrated) Spare Part Information (Continued) Spare Part Number Description Power cords: For use in the United States 350055-001 For use in Australia 350055-011 For use in Europe 350055-021 For use in the United Kingdom 350055-031 For use in Italy 350055-061 For use in Denmark 350055-081 For use in Brazil 350055-201 For use in Japan 350055-291 For use in the People’s Republic of China 350055-AA1 For use in Korea 350055-AD1 For us
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 407107-001 802.11b/g HS WLAN Mini Card module for use in North America 407107-002 802.11b/g HS WLAN Mini Card module for use in the ROW countries or regions listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea Uruguay Venezuela 407107-291 802.11b/g HS WLAN module for use in Japan 407108-001 802.11b/g LJ WLAN module for use in North America 407108-002 802.
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number 407576-002 Description 802.
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 418851-001 1-DIMM, PC2-4200, 512-MB memory module 418852-001 1-DIMM, PC2-4200, 1024-MB memory module 418853-001 1-DIMM, PC2-4200, 2048-MB memory module 418854-001 1-DIMM, PC2-5300, 256-MB memory module 418855-001 1-DIMM, PC2-5300, 512-MB memory module 418856-001 1-DIMM, PC2-5300, 1024-MB memory module 418857-001 1-DIMM, PC2-5300, 2048-MB memory module 418858-001 5400-rpm, 40-GB hard
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 418872-001 65-watt AC adapter 418873-001 90-watt non-PFC AC adapter 418874-001 Intel Core Duo T2600 (2.
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 418891-001 14.1-inch, WXGA+ display panel 418892-001 Display Screw Kit 418893-001 Display Rubber Kit 418894-001 Display Bracket Kit 418895-001 Display enclosure 418896-001 14.
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 418910-041 Keyboard for use in Germany 418910-051 Keyboard for use in France 418910-061 Keyboard for use in Italy 418910-071 Keyboard for use in Spain 418910-081 Keyboard for use in Denmark 418910-091 Keyboard for use in Norway 418910-101 Keyboard for use in Sweden/Finland 418910-111 Keyboard for use in Switzerland 418910-121 Keyboard for use in French Canada 418910-131 Keyboard
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 418910-AB1 Keyboard for use in Taiwan 418910-AD1 Keyboard for use in Korea 418910-BA1 Keyboard for use in Slovenia 418910-BB1 Keyboard for use in Israel 418910-DD1 Keyboard for use in Iceland 418930-001 Heat sink for use only with the UMA system board, spare part number 418931-001 (includes thermal grease, alcohol pad, and thermal pad) 418931-001 UMA system board, for use only with he
Illustrated Parts Catalog Table 3-7 Sequential Part Number Listing (Continued) Spare Part Number Description 438170-001 Fingerprint reader insert (for use as a filler in a non-used fingerprint reader) 438875-001 Heat sink for use only with discrete system boards (spare part numbers 418904-001 and 430495-001), includes thermal grease, alcohol pad, and thermal pad 438876-001 Heat sink for use only with the UMA system board (spare part number 418931-001), includes thermal grease, alcohol pad, and therm
4 Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.
Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. you remove each subassembly from the computer, place ✎ As the subassembly (and all accompanying screws) away from the work area to prevent damage. Plastic Parts Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts.
Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■ Keep electrostatic-sensitive parts in their containers until the parts arrive at static-free workstations.
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to Table 4-2, “Static-Shielding Materials”). ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■ Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
Removal and Replacement Preliminaries 4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are as many as 81 screws, in 14 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement. Refer to Appendix A, “Screw Listing” for detailed information on screw sizes, locations, and usage.
Removal and Replacement Procedures 5.1 Serial Number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.
Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing computer components. Disassembly Sequence Chart Section Description 5.3 Preparing the Computer for Disassembly # of Screws Removed Battery 0 5.4 Hard Drive 2 loosened to remove the hard drive cover 1 loosened to remove the hard drive 4 to disassemble the hard drive 5.5 Computer Feet 0 5.6 Bluetooth Module 1 loosened 5.
Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed 5.10 Keyboard 3 5.11 RTC Battery 0 5.12 Internal Memory Module 0 5.13 Modem Module 2 5.14 Mini Card WWAN Module 2 5.15 Switch Cover 6 5.16 Power Button Board 2 5.17 Fan Assembly 1 5.18 Heat Sink 6 loosened 5.19 Processor 1 loosened 5.20 Display Assembly Display bezel Display hinges Display panel Display inverter Wireless antenna transceivers 7 4 4 6 0 2 5.
Removal and Replacement Procedures 5.3 Preparing the Computer for Disassembly Before you begin any removal or installation procedures: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord.
Removal and Replacement Procedures Battery Spare Part Number Information 8-cell, 5.1-AH 4-cell, 2.5-AH 418867-001 418871-001 4. Remove the battery by following these steps: a. Turn the computer upside down with the rear panel toward you. b. Slide the battery release latch on the right 1 and then the battery release latch on the left 2 to release the battery. c. Slide the battery 3 straight back and remove it. Removing the Battery Reverse the above procedure to install the battery.
Removal and Replacement Procedures 5.4 Hard Drive Hard Drive Spare Part Number Information 7200 rpm 100 GB 80 GB 60 GB 431125-001 431124-001 418861-001 5400 rpm 120 GB 100 GB 80 GB 60 GB 40 GB 440880-001 418863-001 418862-001 418859-001 418858-001 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Position the computer with the front toward you.
Removal and Replacement Procedures 3. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer. 4. Lift the right side of the hard drive cover 2 and swing it up and to the left. 5. Remove the hard drive cover. hard drive cover is included in the Plastics Kit, spare part ✎ The number 418877-001.
Removal and Replacement Procedures 6. Loosen the Phillips PM2.5×13.0 spring-loaded hard drive retention screw 1. 7. Grasp the mylar tab 2 on the hard drive and slide the hard drive 3 to the left to disconnect it from the system board. 8. Remove the hard drive 4 from the hard drive bay.
Removal and Replacement Procedures 9. Remove the four Phillips PM3.0×3.0 hard drive frame screws 1 from each side of the hard drive. 10. Lift the frame 2 straight up to remove if from the hard drive. Removing the Hard Drive Frame Reverse the above procedure to reassemble and install the hard drive.
Removal and Replacement Procedures 5.5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part number 418877-001.
Removal and Replacement Procedures 5.6 Bluetooth Module Bluetooth Module Spare Part Number Information Bluetooth module (includes Bluetooth module cable) 409993-001 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Loosen the Phillips PM2.0×5.0 screw 1 that secures the Bluetooth module cover to the computer. 3. Remove the Bluetooth module cover 2.
Removal and Replacement Procedures 4. Slide the Bluetooth module 1 to the right until the left side of the module is clear of the left side of the clip in the base enclosure. 5. Swing the left side of the Bluetooth module 2 out of the base enclosure. 6. Slide the Bluetooth module 3 to the left until it is removed from the base enclosure. 7. Disconnect the Bluetooth module cable 4 from the Bluetooth module. 8. Remove the Bluetooth module.
Removal and Replacement Procedures 5.7 External Memory Module Memory Module Spare Part Number Information PC2-5300 2048 MB 1024 MB 512 MB 256 MB 418857-001 418856-001 418855-001 418854-001 PC2-4200 2048 MB 1024 MB 512 MB 256 MB 418853-001 418852-001 418851-001 418850-001 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Position the computer with the front toward you.
Removal and Replacement Procedures 3. Loosen the Phillips PM2.0×5.0 screw 1 that secures the memory module compartment cover to the computer. 4. Lift the right edge of the cover 2 and swing it up and to the left. 5. Remove the memory module compartment cover. memory module compartment cover is included in the ✎ The Plastics Kit, spare part number 418877-001.
Removal and Replacement Procedures 6. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 7. Slide the module 2 away from the socket at an angle. 8. Remove the memory module. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing the Memory Module Reverse the above procedure to install a memory module.
Removal and Replacement Procedures 5.8 Mini Card WLAN Module Mini Card WLAN Module Spare Part Number Information 802.11b/g HS WLAN module for use in North America 407107-001 802.11b/g HS WLAN module for use in the countries or regions listed below. These countries or regions are categorized as the rest of the world (ROW). 407107-002 China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea Uruguay Venezuela 802.11b/g HS WLAN module for use in Japan 407107-291 802.
Removal and Replacement Procedures Mini Card WLAN Module Spare Part Number Information (Continued) 802.11a/b/g GL WLAN module for use in the countries or regions listed below. These countries or regions are categorized as most of the world 2 (MOW2).
Removal and Replacement Procedures 1. Prepare the computer for disassembly (Section 5.3). 2. Position the computer with the front toward you. 3. Loosen the Phillips PM2.0×5.0 screw 1 that secures the Mini Card module compartment cover to the computer. 4. Lift the front of the cover 2 and swing it up and toward the back of the computer. 5. Remove the Mini Card module compartment cover. Mini Card module compartment cover is included in the ✎ The Plastics Kit, spare part number 418877-001.
Removal and Replacement Procedures 6. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card WLAN module before disconnecting the cables, then disconnect the auxiliary and main wireless antenna cables 1 from the Mini Card WLAN module. wireless antenna cables are available in the ✎ The Wireless Antenna Kit, spare part number 418899-001. 7. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Mini Card WLAN module to the computer.
Removal and Replacement Procedures 5.9 MultiBay II Device MultiBay II Device Spare Part Number Information DVD±RW and CD-RW Double-Layer Combo Drive DVD±RW and CD-RW Combo Drive DVD-ROM drive 418866-001 418865-001 418864-001 1. Prepare the computer for disassembly (Section 5.3). 2. Position the computer with the left side toward you.
Removal and Replacement Procedures 3. Remove the Phillips PM2.5×5.0 screw 1 that secures the MultiBay II device to the computer. 4. Push in on the right side of the MultiBay II device 2. (The MultiBay II device partially protrudes from the MultiBay II.) 5. Slide the MultiBay II device 3 out of the computer. Removing the MultiBay II Device Reverse the above procedure to install an MultiBay II device.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 3. Remove the three Torx8 T8M2.5×11.0 screws that secure the keyboard to the computer.
Removal and Replacement Procedures 4. Turn the computer display-side up with the front toward you. 5. Open the computer as far as possible. 6. Slide the four release tabs 1 on the rear edge of the keyboard forward. 7. Lift the rear edge of the keyboard 2 and swing it up toward you until it rests on the palm rest.
Removal and Replacement Procedures 8. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is attached and disconnect the keyboard cable 2. 9. Release the ZIF connector 3 to which the pointing stick cable is attached and disconnect the pointing stick cable 4. 10. Remove the keyboard.
Removal and Replacement Procedures 11. If it is necessary to replace the pointing stick cable, turn the keyboard upside down with the space bar toward you. 12. Release the ZIF connector 1 to which the pointing stick cable is attached and disconnect the pointing stick cable 2. pointing stick cable is included with all keyboard spare ✎ The part kits and is also available in the Cable Kit, spare part number 418876-001. Removing the Pointing Stick Cable Reverse the above procedure to install the keyboard.
Removal and Replacement Procedures 5.11 RTC Battery RTC battery is included in the Plastics Kit, spare part ✎ The number 418877-001. 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10). 3. Disconnect the RTC battery cable 1 from the system board and remove the cable from the clips 2 in the top cover. 4. Remove the RTC battery 3 from the clip in the base enclosure. ✎ The RTC battery is secured to the top cover by two-sided tape.
Removal and Replacement Procedures 5.12 Internal Memory Module Memory Module Spare Part Number Information PC2-5300 2048 MB 1024 MB 512 MB 256 MB 418857-001 418856-001 418855-001 418854-001 PC2-4200 2048 MB 1024 MB 512 MB 256 MB 418853-001 418852-001 418851-001 418850-001 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10).
Removal and Replacement Procedures 3. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 4. Slide the module 2 away from the socket at an angle. 5. Remove the memory module. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing the Memory Module Reverse the above procedure to install a memory module.
Removal and Replacement Procedures 5.13 Modem Module Modem Module Spare Part Number Information Modem module 418849-001 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10).
Removal and Replacement Procedures 3. Remove the two Phillips PM2.0×6.0 screws 1 that secure the modem module to the system board. 4. Lift the right side of the modem module 2 to disconnect it from the system board. 5. Disconnect the modem module cable 3 from the modem module. modem module cable is included in the modem module ✎ The spare part kit and is also available in the Cable Kit, spare part number 418876-001. 6. Remove the modem module.
Removal and Replacement Procedures 5.14 Mini Card WWAN Module Mini Card WWAN Module Spare Part Number Information For use with Verizon networks For use with Vodafone networks For use with Cingular networks 418860-001 435098-001 436668-001 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10).
Removal and Replacement Procedures 3. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card WWAN module before disconnecting the cables, then disconnect the auxiliary and main wireless antenna cables 1 from the Mini Card WWAN module. wireless antenna cables are available in the ✎ The Wireless Antenna Kit, spare part number 418899-001. 4. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Mini Card WWAN module to the computer.
Removal and Replacement Procedures 5.15 Switch Cover Switch Cover Spare Part Number Information Switch cover 418900-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard (Section 5.10). 3. Turn the computer upside down with the rear panel toward you. 4. Remove the two T8M2.5×11.0 screws 1 and the four Phillips PM2.0×2.0 screws 2 that secure the switch cover to the computer.
Removal and Replacement Procedures 5. Turn the computer display-side up with front toward you. 6. Open the computer as far as possible. 7. Disconnect the power button board cable 1 from the system board. 8. Insert a thin flat-bladed tool under the hinge cover sections 2 of the switch cover and lift up until the switch cover 3 disengages from the computer. 9. Remove the switch cover. Removing the Switch Cover Reverse the above procedure to install the switch cover.
Removal and Replacement Procedures 5.16 Power Button Board Power Button Board Spare Part Number Information Power button board (includes power button board cable) 418908-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard (Section 5.10). 3. Remove the switch cover (Section 5.15). 4. Remove the two Phillips PM2.5×4.0 screws 1 that secure the power button board to the switch cover. 5. Remove the power button board 2 from the switch cover.
Removal and Replacement Procedures 5.17 Fan Assembly Fan Assembly Spare Part Number Information Fan assembly 418886-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard (Section 5.10). 3. Remove the switch cover (Section 5.15). 4. Disconnect the fan cable 1 from the system board. 5. Remove the Torx8 T8M2.5×7.0 screw 2 that secures the fan assembly to the base enclosure. 6. Remove the fan assembly 3 from the computer.
Removal and Replacement Procedures 5.18 Heat Sink Heat Sink Spare Part Number Information heat sink spare part kits include thermal grease, alcohol pads, and ✎ All thermal pads. For use only with discrete system boards (spare part numbers 418904-001 and 430495-001) For use only with discrete system boards For use only with the UMA system board (spare part number 418931-001) For use only with the UMA system board 418887-001 438875-001 418930-001 438876-001 1.
Removal and Replacement Procedures 2. Noting the required screw removal sequence, loosen the four Phillips PM2.0×10.0 screws 1 and the two Phillips PM2.0×13.0 screws 2 that secure the heat sink to the system board. heat sink has numbers stamped on it that indicate the ✎ The required screw removal sequence. You must remove screws in the order indicated to avoid over torque and binding problems. 3. Remove the heat sink 3 from the base enclosure.
Removal and Replacement Procedures thermal paste and thermal pads should be thoroughly ✎ The cleaned from the surfaces of the heat sink 1, processor 2, Chip1 3, and Chip2 4 each time the heat sink is removed. Thermal paste and thermal pads are included with all heat sink, processor, and system board spare part kits. Thermal Paste and Thermal Pad Locations Reverse the above procedure to install the heat sink.
Removal and Replacement Procedures 5.19 Processor Processor Spare Part Number Information Intel Core Duo T7600 (2.33-GHz) processor Intel Core Duo T7400 (2.16-GHz) processor Intel Core Duo T7200 (2.0-GHz) processor Intel Core Duo T5600 (1.83-GHz) processor Intel Core Duo T5500 (1.66-GHz) processor Intel Core Duo T2300E (1.66-GHz) processor Intel Core Duo T2600 (2.17-GHz) processor Intel Core Duo T2500 (2.00-GHz) processor Intel Core Duo T2400 (1.83-GHz) processor Intel Core Duo T2300 (1.
Removal and Replacement Procedures 2. Use a flat-bladed screwdriver to turn the processor locking screw 1 one-half turn counterclockwise until you hear a click. 3. Lift the processor 2 straight up and remove it. The gold triangle 3 on the processor should be aligned with ✎ the triangle icon 4 on the processor socket when you install the processor. Removing the Processor Reverse the above procedure to install the processor.
Removal and Replacement Procedures 5.20 Display Assembly Display Assembly Spare Part Number Information 14.1-inch, WXGA+ 14.1-inch, WXGA 418907-001 418896-001 1. Prepare the computer for disassembly (Section 5.3). 2. Disconnect the wireless antenna cables from the Mini Card WLAN module (Section 5.8). 3. Remove the keyboard (Section 5.10). 4. Disconnect the wireless antenna cables from the Mini Card WWAN module (Section 5.14). 5. Remove the switch cover (Section 5.15).
Removal and Replacement Procedures 6. Close the computer and turn it upside down with the rear panel toward you. 7. Remove the following screws: 1 Two Torx8 T8M2.5×11.0 screws from the computer bottom 2 Two Torx8 T8M2.5×7.0 screws from the computer rear panel 3 One Phillips PM2.5×5.
Removal and Replacement Procedures 8. Turn the computer display-side up with the front toward you. 9. Open the computer as far as it will open. 10. Disconnect the display cable 1 from the system board. 11. Remove the wireless antenna cables 2 and 3 from the Mini Card compartment and the top cover clips.
Removal and Replacement Procedures Ä CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components. 12. Remove the two Torx8 T8M2.5×7.0 screws 1 that secure the display assembly to the computer. 13. Lift the display assembly 2 straight up and remove it.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display bezel 418889-001 Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA 418891-001 418890-001 Display Hinge Kit 418902-001 Display Inverter 418888-001 Wireless Antenna Kit 418899-001 Display enclosure 418895-001 Display Bracket Kit (includes left display bracket) Display Cable Kit (for use with 14.1-inch, WXGA+ display panel) Display Cable Kit (for use with 14.
Removal and Replacement Procedures 14. Remove the following: 1 and 2 four rubber screw covers The two rubber screw covers 1 on the top edge of the display ✎ bezel are different from the two rubber screw covers 2 on the bottom edge of the display bezel. Both types of rubber screw covers are included in the Display Rubber Kit, spare part number 418893-001. 3 Four Phillips PM2.5×6.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display bezel 418889-001 Display enclosure 418895-001 15. Flex the insides edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure. 16. Remove the display bezel 3.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display Hinge Kit 418902-001 17. If it is necessary to replace the display hinges, remove the Phillips PM2.5×4.0 screw 1 and the Phillips PM2.5×6.0 screw 2 that secure each hinge to the display enclosure. 18. Remove the display hinges 3.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA 418891-001 418890-001 19. Remove the four mylar screw covers 1 and the four Phillips PM2.0×3.0 screws 2 that secure the display panel to the display enclosure. 20. Remove the two Phillips PM2.5×6.0 screws 3 that secure the display inverter to the display enclosure. 21.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display Inverter 418888-001 22. Disconnect the display 1 and backlight cables 2 from the inverter. 23. Remove the inverter 3.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Wireless Antenna Kit 418899-001 24. If it is necessary to replace the wireless antenna transceivers and cables, remove the two Torx T8M2.5×4.0 screws 1 that secure the left and right transceivers to the display enclosure. 25. Remove the wireless antenna cables 2 from the clips in the display enclosure. 26. Detach the wireless antenna transceivers 3 from the display enclosure. 27.
Removal and Replacement Procedures 5.21 Top Cover Top Cover Spare Part Number Information Top cover (includes TouchPad, smart card reader, and fingerprint reader board) Top cover (includes TouchPad and smart card reader) 418882-001 438169-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Keyboard (Section 5.10) b. Switch cover (Section 5.15) c. Fan assembly (Section 5.17) d. Heat sink (Section 5.18) e. Display assembly (Section 5.20) 2.
Removal and Replacement Procedures 3. Remove the following: 1 Two rubber screw covers 2 Nine Torx8 T8M2.5×11.0 screws that secure the top cover to the base enclosure 3 One Phillips PM2.5×5.
Removal and Replacement Procedures 4. Turn the computer right-side up with the front toward you. 5.
Removal and Replacement Procedures 6. Remove the microphone 1 from the clip in the top cover and the cable 2 from the routing clips in the top cover.
Removal and Replacement Procedures 7. Remove the two Torx8 T8M2.5×7.0 screws that secure the top cover to the base enclosure.
Removal and Replacement Procedures 8. Swing the rear edge of the top cover 1 up and forward 2 until the left and right sides disengage from the base enclosure. 9. Remove the top cover 3. Removing the Top Cover Reverse the above procedure to install the top cover.
Removal and Replacement Procedures 5.22 PC Card/Digital Media Board PC Card/Digital Media Board Spare Part Number Information PC Card/digital media board 418884-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Keyboard (Section 5.10) b. Switch cover (Section 5.15) c. Fan assembly (Section 5.17) d. Heat sink (Section 5.18) e. Display assembly (Section 5.20) f. Top cover (Section 5.
Removal and Replacement Procedures 2. Remove the three Phillips PM2.5×5.0 screws 1 that secure the PC Card/digital media board to the system board. 3. Lift up on the right side of the PC Card/digital media board 2 to disconnect the board from the system board.
Removal and Replacement Procedures 4. If it is necessary to remove the PC Card assembly from the digital media board, disengage the hooks 1 on the PC Card assembly from the tabs on the digital media board. 5. Remove the PC Card assembly 2 from the digital media board. Removing the PC Card Assembly Reverse the above procedure to reassemble and install the PC Card/digital media board.
Removal and Replacement Procedures 5.23 Speaker Speaker Spare Part Number Information Speaker 418883-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Keyboard (Section 5.10) b. Switch cover (Section 5.15) c. Fan assembly (Section 5.17) d. Heat sink (Section 5.18) e. Display assembly (Section 5.20) f. Top cover (Section 5.21) g. PC Card/digital media board (Section 5.
Removal and Replacement Procedures 2. Disconnect the speaker cable 1 from the system board. 3. Remove the speaker 2 from the base enclosure. Removing the Speaker Reverse the above procedure to install the speaker.
Removal and Replacement Procedures 5.24 Microphone Microphone Spare Part Number Information Microphone 418903-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Keyboard (Section 5.10) b. Switch cover (Section 5.15) c. Fan assembly (Section 5.17) d. Heat sink (Section 5.18) e. Display assembly (Section 5.20) f. Top cover (Section 5.21) g. PC Card/digital media board (Section 5.
Removal and Replacement Procedures 2. Disconnect the microphone cable 1 from the system board. 3. Remove the microphone 2 from the base enclosure. Removing the Microphone Reverse the above procedure to install the microphone.
Removal and Replacement Procedures 5.25 System Board System Board Spare Part Number Information system board spare part kits include thermal grease, alcohol pads, ✎ All and thermal pads.
Removal and Replacement Procedures 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. b. c. d. e. f. g. h. i. j. k. l. Hard drive (Section 5.4) Bluetooth board (Section 5.6) MultiBay II device (Section 5.9) Keyboard (Section 5.10) Switch cover (Section 5.15) Fan assembly (Section 5.17) Heat sink (Section 5.18) Display assembly (Section 5.20) Top cover (Section 5.21) PC Card/digital media board (Section 5.22) Speaker (Section 5.23) Microphone (Section 5.
Removal and Replacement Procedures 2. Turn the computer upside down with the front toward you. 3. Remove the two Phillips PM2.0×6.0 screws on each side of the hard drive connector that secure the system board to the base enclosure.
Removal and Replacement Procedures 4. Turn the computer right-side up with the front toward you. 5. Remove the audio board cables 1 from the space between the system board and the base enclosure. 6. Disconnect the audio board cable 2 from the system board. 7. Disconnect the Bluetooth module cable 3 from the system board and remove the cable from the base enclosure. audio board and Bluetooth module cables are available in ✎ The the Cable Kit, spare part number 418876-001.
Removal and Replacement Procedures 8. Disconnect the modem module cable 1 from the system board. modem module cable is available in the Cable Kit, spare ✎ The part number 418876-001. 9. Release the ZIF connector 2 to which the LED board cable is attached and disconnect the LED board cable 3 from the system board.
Removal and Replacement Procedures 10. Remove the four Phillips PM2.5×5.0 screws that secure the system board to the base enclosure.
Removal and Replacement Procedures 11. Use the hard drive connector 1 to lift the right side of the system board 2 until it rests at an angle. 12. Slide the system board 3 away at an angle and remove it.
Removal and Replacement Procedures 13. If it is necessary to replace the audio cable, disconnect the cable from the three connectors on the system board and remove the cable. audio cable is available in the Cable Kit, spare part number ✎ The 418876-001.
Removal and Replacement Procedures 14. If it is necessary to replace the modem connector and cable, remove the connector 1 from the clip in the base enclosure and remove the cable 2 from the routing channel in the base enclosure. modem cable is available in the Cable Kit, spare part ✎ The number 418876-001. Removing the Modem Connector and Cable Reverse the above procedures to install the system board.
Removal and Replacement Procedures 5.26 MultiBay II Eject Assembly MultiBay II Eject Assembly Spare Part Number Information MultiBay II eject assembly 418905-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Hard drive (Section 5.4) b. Bluetooth board (Section 5.6) c. MultiBay II device (Section 5.9) d. Keyboard (Section 5.10) e. Switch cover (Section 5.15) f. Fan assembly (Section 5.17) g. Heat sink (Section 5.18) h. Display assembly (Section 5.
Removal and Replacement Procedures 2. Remove the Phillips PM2.0×6.0 screw 1 that secures the MultiBay II eject assembly to the base enclosure. 3. Remove the MultiBay II eject assembly 2 from the base enclosure. Removing the MultiBay II Eject Assembly Reverse the above procedure to install the MultiBay II eject assembly.
6 Specifications This chapter provides physical and performance specifications. Table 6-1 Computer Dimensions Height (front to back) Width Depth Weight Metric U.S. 2.9 to 3.4 cm 33.1 cm 23.9 cm 1.1 to 1.3 in 13.0 in 9.4 in 2.2 kg 4.9 lbs Input Power Operating voltage Operating current 18.5 V dc @ 3.5 A – 65 W 19.0 V dc @ 4.74 A – 90 W 3.5 A or 4.
Specifications Table 6-1 Computer (Continued) Relative humidity (noncondensing) Operating Nonoperating 10% to 90% 5% to 95% 10% to 90% 5% to 95% -15 m to 3,048 m -15 m to 12,192 m -50 ft to 10,000 ft -50 ft to 40,000 ft Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) Nonoperating (14.7 to 4.4 psia) Shock Operating Nonoperating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Random Vibration Operating Nonoperating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate 1.
Specifications Table 6-2 14.1-inch, WXGA Dimensions Height Width Diagonal 21.3 cm 28.5 cm 35.8 cm Number of colors Up to 16.8 million Contrast ratio 250:1 Brightness 180 nits typical 8.4 in 11.2in 14.1 in Pixel resolution Pitch Format Configuration 0.279 × 0.279 mm 1024 × 768 RGB vertical stripe Backlight Edge lit Character display 80 × 25 Total power consumption 4.
Specifications Table 6-3 Hard Drives 120-GB* 100-GB* 80-GB* 9.5 mm 70 mm 99 g 9.5 mm 70 mm 99 g 9.5 mm 70 mm 99 g SATA SATA SATA 150 MB/sec ATA security 150 MB/sec ATA security 100 MB/sec 1.5 ms 10.5 ms 22 ms 1 ms 10 ms 18 ms Dimensions Height Width Weight Interface type Transfer rate Synchronous (maximum) Security ATA security Seek times (typical read, including setting) Single track Average Maximum 2 ms 12 ms 22 ms Logical blocks† 234,441,648 195,371,568 156.301.
Specifications Table 6-3 Hard Drives 100-GB* 80-GB* 60-GB* 40-GB* 9.5 mm 70 mm 99 g 9.5 mm 70 mm 99 g 9.5 mm 70 mm 99 g 9.
Specifications Table 6-4 DVD±RW and CD-RW Combo Drive Applicable disc Read: DVD-R, DVD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Write: CD-R and CD-RW DVD-R and DVD-RW Disc diameter Standard disc Mini disc 6–6 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-4 DVD±RW and CD-RW Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD DVD < 175 ms < 285 ms < 230 ms < 335 ms Random Full stroke Audio output level Audio-out, 0.
Specifications Table 6-5 DVD-ROM Drive Applicable disc DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 12 cm (4.72 in) 8 cm (3.15 in) Disc thickness 1.2 mm (0.047 in) Track pitch 0.
Specifications Table 6-6 System DMA Hardware DMA System Function DMA0 Not applicable DMA1* Not applicable DMA2* Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5* Available for PC Card DMA6 Not assigned DMA7 Not assigned *PC Card controller can use DMA 1, 2, or 5.
Specifications Table 6-7 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Standard 101-/102-Key or Microsoft Natural Keyboard IRQ2 Cascaded IRQ3 Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* Intel USB UHCI controller—24C2 Intel 82852/8
Specifications Table 6-7 System Interrupts (Continued) IRQ11 Intel USB EHCI controller—24CD Intel USB UHCI controller—24C4 Intel USB UHCI controller—24C7 Intel Pro/Wireless 2200BG TI OHCI 1394 host controller TI PCI1410 CardBus controller IRQ12 Synaptics PS/2 TouchPad IRQ13 Numeric data processor IRQ14 Primary IDE channel IRQ15 Secondary IDE channel *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
Specifications Table 6-8 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 000 - 00F DMA controller no. 1 010 - 01F Unused 020 - 021 Interrupt controller no.
Specifications Table 6-8 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0A2 - 0BF Unused 0C0 - 0DF DMA controller no.
Specifications Table 6-8 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 2F0 - 2F7 Unused 2F8 - 2FF Infrared port 300 - 31F Unused 320 - 36F Unused 370 - 377 Secondary diskette drive controller 378 - 37F Parallel port (LPT1/default) 380 - 387 Unused 388 - 38B FM synthesizer—OPL3 38C - 3AF Unused 3B0 - 3BB VGA 3BC - 3BF Reserved (parallel port/no EPP support) 3C0 - 3DF VGA 3E0 - 3E1 PC Card controller in CPU 3E2 - 3E3 Unused 3E8 - 3EF
Specifications Table 6-9 System Memory Map Size Memory Address System Function 640 KB 00000000-0009FFFF Base memory 128 KB 000A0000-000BFFFF Video memory 48 KB 000C0000-000CBFFF Video BIOS 160 KB 000C8000-000E7FFF Unused 64 KB 000E8000-000FFFFF System BIOS 15 MB 00100000-00FFFFFF Extended memory 58 MB 01000000-047FFFFF Super extended memory 58 MB 04800000-07FFFFFF Unused 2 MB 08000000-080FFFFF Video memory (direct access) 4 GB 08200000-FFFEFFFF Unused 64 KB FFFF0000-FFFFFF
A Screw Listing This appendix provides specification and reference information for the screws used in the computer. All screws listed in this appendix are available in the Screw Kit, spare part number 418878-001, and the Display Screw Kit, spare part number 418892-001. Table A-1 Phillips PM3.0×3.0 Screw mm Color Qty. Length Thread Head Width Black 4 3.0 mm 3.0 mm 5.0 mm Where used: 4 screws that secure the hard drive frame to the hard drive (documented in Section 5.4) Phillips PM3.0×3.
Screw Listing Table A-2 Phillips PM2.0×5.0 Screw mm Color Qty. Length Thread Head Width Black 5 5.0 mm 2.0 mm 5.0 mm Where used: 1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.4) 2 One screw that secures the Bluetooth module cover to the computer (screw is captured on the cover by a C-clip; documented in Section 5.
Screw Listing Table A-3 Phillips PM2.5×13.0 Spring-Loaded Screw mm Color Qty. Length Thread Head Width Silver 1 13.0 mm 2.5 mm 6.0 mm Where used: One screw that secures the hard drive to the computer (screw is captured on the cover by a C-clip; documented in Section 5.4) Phillips PM2.5×13.
Screw Listing Table A-4 Phillips PM2.5×5.0 Screw mm Color Qty. Length Thread Head Width Black 9 5.0 mm 2.5 mm 5.0 mm Where used: One screw that secures the MultiBay II device to the computer (documented in Section 5.9) Phillips PM2.5×5.
Screw Listing Table A-4 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 9 5.0 mm 2.5 mm 5.0 mm Where used: 1 One screw that secures the display assembly to the computer (documented in Section 5.20) 2 One screw that secures the top cover to the computer (documented in Section 5.21) Phillips PM2.5×5.
Screw Listing Table A-4 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 9 5.0 mm 2.5 mm 5.0 mm Where used: 3 screws that secure the PC Card/digital media board to the computer (documented in Section 5.22) Phillips PM2.5×5.
Screw Listing Table A-4 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 9 5.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the system board to the computer (documented in Section 5.25) Phillips PM2.5×5.
Screw Listing Table A-5 Torx8 T8M2.5×11.0 Screw mm Color Qty. Length Thread Head Width Black 16 11.0 mm 2.5 mm 5.0 mm Where used: 1 Three screws that secure the keyboard to the computer (documented in Section 5.10) 2 Two screws that secure the switch cover to the computer (documented in Section 5.15) 3 Two screws that secure the display assembly to the computer (documented in Section 5.20) Torx8 T8M2.5×11.
Screw Listing Table A-5 Torx8 T8M2.5×11.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 16 11.0 mm 2.5 mm 5.0 mm Where used: 9 screws that secure the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×11.
Screw Listing Table A-6 Phillips PM2.0×6.0 Screw mm Color Qty. Length Thread Head Width Silver 5 6.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the modem module to the computer (documented in Section 5.13) Phillips PM2.0×6.
Screw Listing Table A-6 Phillips PM2.0×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 5 6.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the system board to the computer (documented in Section 5.25) Phillips PM2.0×6.
Screw Listing Table A-6 Phillips PM2.0×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 5 6.0 mm 2.0 mm 5.0 mm Where used: One screw that secures the MultiBay II eject assembly to the base enclosure (documented in Section 5.26) Phillips PM2.0×6.
Screw Listing Table A-7 Phillips PM2.0×3.0 Screw mm Color Qty. Length Thread Head Width Silver 4 3.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the Mini Card WLAN to the computer (documented in Section 5.8) Phillips PM2.0×3.
Screw Listing Table A-7 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 4 3.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the Mini Card WWAN to the computer (documented in Section 5.14) Phillips PM2.0×3.
Screw Listing Table A-8 Phillips PM2.5×4.0 Screw mm Color Qty. Length Thread Head Width Silver 4 4.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the power button board to the switch cover (documented in Section 5.16) Phillips PM2.5×4.
Screw Listing Table A-8 Phillips PM2.5×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 4 4.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display hinges to the display assembly (documented in Section 5.20) Phillips PM2.5×4.
Screw Listing Table A-9 Torx8 T8M2.5×4.0 Screw mm Color Qty. Length Thread Head Width Silver 2 4.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the wireless antenna transceivers to the display assembly (documented in Section 5.20) Torx8 T8M2.5×4.
Screw Listing Table A-10 Phillips PM2.5×10.0 Screw mm Color Qty. Length Thread Head Width Silver 4 10.0 mm 2.5 mm 6.0 mm Where used: 1 Four screws that secure the heat sink to the computer (screws are secured to the heat sink by C-clips; documented in Section 5.18) Table A-11 Phillips PM2.5×13.0 Screw mm Color Qty. Length Thread Head Width Silver 2 13.0 mm 2.5 mm 6.
Screw Listing Table A-12 Phillips PM2.0×2.0 Screw mm Color Qty. Length Thread Head Width Black 4 2.0 mm 2.0 mm 6.0 mm Where used: 4 screws that secure the switch cover to the computer (documented in Section 5.15) Phillips PM2.0×2.
Screw Listing Table A-13 Torx8 T8M2.5×7.0 Screw mm Color Qty. Length Thread Head Width Black 8 7.0 mm 2.5 mm 5.0 mm Where used: One screw that secures the fan assembly to the computer (documented in Section 5.17) Torx8 T8M2.5×7.
Screw Listing Table A-13 Torx8 T8M2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 7.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display assembly to the computer (documented in Section 5.20) Torx8 T8M2.5×7.
Screw Listing Table A-13 Torx8 T8M2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 7.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display assembly to the computer (documented in Section 5.20) Torx8 T8M2.5×7.
Screw Listing Table A-13 Torx8 T8M2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 7.0 mm 2.5 mm 5.0 mm Where used: One screw that secures the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×7.
Screw Listing Table A-13 Torx8 T8M2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 7.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×7.
Screw Listing Table A-14 Phillips PM2.5×6.0 Screw mm Color Qty. Length Thread Head Width Silver 8 6.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the display bezel to the display assembly (documented in Section 5.20) Phillips PM2.5×6.
Screw Listing Table A-14 Phillips PM2.5×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 8 6.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display hinges to the display assembly (documented in Section 5.20) Phillips PM2.5×6.
Screw Listing Table A-14 Phillips PM2.5×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 8 6.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display panel to the display assembly (documented in Section 5.20) Phillips PM2.5×6.
B Backup and Recovery in Windows Vista can only recover files that you have previously backed up. ✎ You HP recommends that you use HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer.
Backup and Recovery in Windows Vista Backup Suggestions ■ Create a set of recovery discs using HP Backup & Recovery Manager. ■ Create system recovery points using HP Backup & Recovery Manager, and periodically copy them to disc. ■ Store personal files in the Documents folder and back up these folders periodically. ■ Back up templates stored in their associated programs. ■ Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
Backup and Recovery in Windows Vista Backing Up Specific Files or Folders You can back up specific files or folders to the recovery partition on the hard drive, to an optional external hard drive, or to optical discs (CDs or DVDs). process will take several minutes, depending on the file ✎ This size and the speed of the computer. To back up specific files or folders: 1. Select Start > All Programs > HP Backup & Recovery > Backup and Recovery Manager. 2. Click Next. 3.
Backup and Recovery in Windows Vista To back up your entire hard drive: 1. Select Start > All Programs > HP Backup & Recovery > Backup and Recovery Manager. 2. Click Next. 3. Click Back up to protect system settings and important data files, and then click Next. 4. Click Back up entire hard drive, and then click Next. 5. Follow the on-screen instructions. Creating Recovery Points When you back up modifications since your last backup, you are creating system recovery points.
Backup and Recovery in Windows Vista 3. Click Back up to protect system settings and important data files, and then click Next. 4. Click Create or manage Recovery Points, and then click Next. 5. Follow the on-screen instructions. Scheduling Backups Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific files and folders.
Backup and Recovery in Windows Vista HP Backup and Recovery Manager helps you with the following tasks for safeguarding your information and restoring it in case of a system failure: ■ Recovering important files—This feature helps you reinstall important files without performing a full system recovery. ■ Performing a full system recovery—With HP Backup and Recovery Manager, you can recover your full factory image if you experience system failure or instability.
Backup and Recovery in Windows Vista 4. Click Recover important files or the entire system, and then click Next. 5. Follow the on-screen instructions. Initiating a Recovery from the Hard Drive Recovery Partition To initiate a recovery from the hard drive recovery partition, follow these steps: 1. Back up all personal files. 2. Restart the computer, and then press f11 before the Windows operating system loads. 3. Click a recovery option, and then click Next. 4. Follow the on-screen instructions.
C Backup and Recovery in Windows XP Creating Recovery Discs After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory image. The recovery discs are used to start up (boot) the computer and recover the operating system and software to factory settings in case of system instability or failure. Note the following guidelines before creating recovery discs: ■ You will need high-quality CD-R, DVD-R, or DVD+R media (purchased separately).
Backup and Recovery in Windows XP To create a set of recovery discs: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next. 3. Click Create factory software recovery CDs or DVDs to recover the system (Highly recommended), and then click Next. 4. Follow the on-screen instructions. Backing Up Your information can only recover files that you have previously backed up.
Backup and Recovery in Windows XP Backup Suggestions ■ Create a set of recovery discs using HP Backup and Recovery Manager. ■ Create system recovery points using HP Backup and Recovery Manager, and periodically copy them to disc. ■ Store personal files in the My Documents folder and back up these folders periodically. ■ Back up templates stored in their associated programs. ■ Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
Backup and Recovery in Windows XP Backing Up Specific Files or Folders You can back up specific files or folders to the recovery partition on the hard drive, to an optional external hard drive, or to optical discs (CDs or DVDs). process will take several minutes, depending on the file ✎ This size and the speed of the computer. To back up specific files or folders: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next. 3.
Backup and Recovery in Windows XP 2. Click Next. 3. Click Back up to protect system settings and important data files, and then click Next. 4. Click Back up entire hard drive, and then click Next. 5. Follow the on-screen instructions. Creating Recovery Points When you back up modifications since your last backup, you are creating system recovery points. This allows you to save a snapshot of your hard drive at a specific point in time.
Backup and Recovery in Windows XP 4. Click Create or manage Recovery Points, and then click Next. 5. Follow the on-screen instructions. Scheduling Backups Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly, or monthly) or at specific events, such as at system restart or when you dock to an optional docking station (select models only).
Backup and Recovery in Windows XP Performing a Recovery from the Recovery Discs To perform a recovery from the recovery discs, follow these steps: 1. Back up all personal files. 2. Insert the first recovery disc into the optical drive and restart the computer. 3. Follow the on-screen instructions.
Backup and Recovery in Windows XP Initiating a Recovery from the Hard Drive Recovery Partition To initiate a recovery from the hard drive recovery partition, follow these steps: 1. Back up all personal files. 2. Restart the computer, and then press f11 before the Windows operating system loads. 3. Click a recovery option, and then click Next. 4. Follow the on-screen instructions.
D Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Ä CAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components.
Display Component Recycling This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2. procedures differ from one display assembly to ✎ Disassembly another. The procedures provided in this appendix are general disassembly instructions.
Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3.
Display Component Recycling 4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
Display Component Recycling 5. Remove all screws 1 that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly 2 from the display enclosure.
Display Component Recycling 7. Turn the display panel assembly upside down. 8. Remove all screws that secure the display panel frame to the display panel.
Display Component Recycling 9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame. 10. Remove the display panel frame 2 from the display panel.
Display Component Recycling 11. Remove the screws 1 that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover 2 and swing it forward. 13. Remove the backlight cover.
Display Component Recycling 14. Turn the display panel right-side up. 15. Remove the backlight cables 1 from the clip 2 in the display panel.
Display Component Recycling 16. Turn the display panel upside down. 17. Remove the backlight frame from the display panel.
Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Slide the backlight out of the backlight frame.
Display Component Recycling 19. Disconnect the display cable 1 from the LCD panel. 20. Remove the screws 2 that secure the LCD panel to the display rear panel. 21. Release the LCD panel 3 from the display rear panel. 22. Release the tape 4 that secures the LCD panel to the display rear panel.
Display Component Recycling 23. Remove the LCD panel. Removing the LCD Panel 24. Recycle the LCD panel and backlight.
E Connector Pin Assignments Table D-1 Audio-Out (Headphone) Pin Signal Pin Signal 1 Audio out, left channel 3 Ground 2 Audio out, right channel Maintenance and Service Guide E–1
Connector Pin Assignments Table D-2 Audio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Table D-3 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground E–2 Maintenance and Service Guide
Connector Pin Assignments Table D-4 S-Video-Out Pin Signal Pin Signal 1 S-VHS color (C) signal 5 TV-CD 2 Composite video signal 6 S-VHS intensity ground 3 S-VHS intensity (Y) signal 7 Composite video ground 4 S-VHS color ground Maintenance and Service Guide E–3
Connector Pin Assignments Table D-5 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4 Not connected 12 DDC 2B data 5 Ground 13 Horizontal sync 6 Ground analog 14 Vertical sync 7 Ground analog 15 DDC 2B clock 8 Ground analog E–4 Maintenance and Service Guide
Connector Pin Assignments Table D-6 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2 Tip 5 Unused 3 Ring 6 Unused Maintenance and Service Guide E–5
Connector Pin Assignments Table D-7 RJ-45 (Network) Pin Signal Pin Signal 1 Transmit + 5 Unused 2 Transmit – 6 Receive – 3 Receive + 7 Unused 4 Unused 8 Unused E–6 Maintenance and Service Guide
F Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries or regions must meet the requirements of the country or region where the computer is used.
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries or regions. F–2 ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used.
Power Cord Set Requirements Country/Region-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Accredited Agency Applicable Note Number Korea EK 4 The Netherlands KEMA 1 Norway NEMKO 1 People’s Republic of China CCC 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 United Kingdom BSI 1 United States UL 2 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Index A AC adapter, spare part numbers 3–21, 3–27 accessory battery connector 1–22 arrow keys 1–15 audio cable illustrated 3–19 removal 5–71 audio troubleshooting 2–25 audio-in jack location 1–11 pin assignments E–2 audio-out jack location 1–11 pin assignments E–1 B backing up hard drive Windows Vista B–3 Windows XP C–4 specific files or folders Windows Vista B–3 Windows XP C–4 system modifications C–6 the system C–3 Maintenance and Service Guide backup C–2 Backup and Recovery Windows Vista B–1 Windows X
Index C Cable Kit contents 3–19 spare part number 3–5, 3–19, 3–27 cables, service considerations 4–2 caps lock key 1–15 caps lock light 1–19 carrying case, spare part number 3–21, 3–23 CMOS clearing 1–4 components bottom 1–22 front 1–6 keyboard 1–12, 1–14 left-side 1–10 rear 1–10 right-side 1–8 top 1–16, 1–18, 1–20 computer feet illustrated 3–18 locations 5–11 Computer Setup Advanced Menu 2–7 Diagnostics Menu 2–7 File menu 2–4 menus 2–4 overview 2–1 Security Menu 2–5 computer specifications 6–1 connector p
Index display component recycling D–1 display enclosure illustrated 3–16 spare part number 3–17, 3–28, 5–48, 5–50 display hinge illustrated 3–16 removal 5–51 Display Hinge Kit, spare part number 3–17, 3–28, 5–48, 5–51 display inverter illustrated 3–16 removal 5–53 spare part number 3–17, 3–27, 5–48, 5–53 display panel illustrated 3–16 removal 5–52 spare part numbers 3–17, 3–27, 3–28, 5–48, 5–52 display release button 1–7 Display Rubber Kit, spare part number 3–28 Display Screw Kit, spare part number 3–17,
Index fingerprint reader insert, spare part numbers 3–21, 3–31 flowcharts, troubleshooting no audio 2–25, 2–26 no network/modem connection 2–30 no OS loading 2–19 no OS loading from diskette drive 2–23 no OS loading from hard drive 2–20, 2–21, 2–22 no OS loading from optical drive 2–24 no power 2–12, 2–14, 2–15 no video 2–16, 2–17 nonfunctioning device 2–27 nonfunctioning docking device 2–18 nonfunctioning keyboard 2–28 nonfunctioning pointing device 2–29 fn key 1–15 front components 1–6 G grounding equip
Index K keyboard removal 5–23 spare part numbers 3–3, 3–28, 3–29, 3–30, 5–23 troubleshooting 2–28 keyboard components 1–12, 1–14 keypad 1–15 L Label Kit, spare part number 3–21, 3–27 LED board, spare part number 3–9, 3–28 left-side components 1–10 M mass storage devices, spare part numbers 3–20 memory map specifications 6–15 memory module removal 5–14, 5–29 spare part numbers 3–5, 3–25, 3–26, 5–14, 5–29 memory module compartment 1–23 memory module compartment cover illustrated 3–18 removal 5–15 microphon
Index MultiBay II device 1–9 removal 5–21 spare part numbers 5–21 MultiBay II eject assembly removal 5–77 spare part number 3–9, 3–28, 5–77 N network jack location 1–9 pin assignments E–6 network, troubleshooting 2–30 nonfunctioning device, troubleshooting 2–18, 2–27 num lock key 1–15 num lock light 1–19 O optical drive OS loading problems 2–24 precautions 4–3 removal 5–21 spare part numbers 3–11, 3–20, 3–21, 5–21 specifications 6–6, 6–8 P packing precautions 4–5 password clearing 1–4 PC Card slot bezel
Index R rear components 1–10 Recovery Windows Vista B–5 removal/replacement preliminaries 4–1 procedures 5–1 right-side components 1–8 RJ-11 jack location 1–9 pin assignments E–5 RJ-45 jack location 1–9 pin assignments E–6 RTC battery removal 5–28 spare part number 3–5, 3–27 S safeguarding your data C–2 scheduling backups Windows Vista B–5 Screw Kit contents A–1 spare part number 3–22, 3–27, A–1 screw listing A–1 security cable slot 1–13 serial number 1–23, 3–1, 5–2 service considerations 4–2 smart card s
Index Index–8 T U thermal pads, replacing 5–41 thermal paste, replacing 5–41 tools required 4–1 top components 1–16, 1–18, 1–20 top cover removal 5–55 spare part number 3–5, 3–27, 3–30, 5–55 TouchPad 1–21 TouchPad cable, illustrated 3–19 TouchPad left/right buttons 1–21 TouchPad scroll zone 1–21 transporting precautions 4–5 troubleshooting audio 2–25 expansion product 2–18 flowcharts 2–10 keyboard 2–28 modem 2–30 network 2–30 nonfunctioning device 2–18, 2–27 OS loading 2–19 overview 2–1 pointing device
