Specifications

ManualsBrandsCompaq ManualsComputersML310 - ProLiant - 128 MB RAM

HP ProLiant ML310 Server

Maintenance and Service Guide

April 2003 (Fifth Edition)

Part Number 274429-005

HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:42 AM

Summary of content (90 pages)

PAGE 1
HP ProLiant ML310 Server Maintenance and Service Guide April 2003 (Fifth Edition) Part Number 274429-005 HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:42 AM
PAGE 2
© 2002, 2003 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation. Intel and Pentium are trademarks of Intel Corporation in the U.S. and other countries and are used under license. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice.
PAGE 3
Contents About This Guide Audience Assumptions............................................................................................................................... vii Technician Notes........................................................................................................................................ vii Where to Go for Additional Help.................................................................................................................ix Integrated Management Log ...
PAGE 4
Contents Expansion Slots........................................................................................................................................2-28 Removing an Expansion Slot Retainer ....................................................................................................2-29 Expansion Board Guide ...........................................................................................................................2-30 Memory Modules.........................................
PAGE 5
Contents List of Figures 1-1 1-2 1-3 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 2-31 2-32 2-33 2-34 2-35 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 Mechanical parts exploded view......................................................................................................... 1-2 Server components exploded view (ATA model)...............................................................................
PAGE 6
Contents List of Tables 1-1 1-2 2-1 2-2 2-3 2-4 3-1 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 vi Mechanical Spare Parts List ................................................................................................................1-3 Server Components Spare Parts List ...................................................................................................1-6 Storage Device Drive Bay Description ..........................................................
PAGE 7
About This Guide This maintenance and service guide can be used for reference when servicing HP ProLiant ML310 servers. WARNING: To reduce the risk of personal injury from electric shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs can create conditions that are hazardous. Audience Assumptions This guide is for service technicians.
PAGE 8
About This Guide CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of clearance at the front and back of the server. CAUTION: The computer is designed to be electrically grounded (earthed). To ensure proper operation, plug the AC power cord into a properly grounded AC outlet only. NOTE: Any indications of component replacement or printed wiring board modifications may void any warranty.
PAGE 9
About This Guide Where to Go for Additional Help In addition to this guide, the following information sources are available: • User documentation • Service Quick Reference Guide • Service training guides • HP service advisories and bulletins • QuickFind information services • Insight Manager software For additional copies, go to www.hp.com Integrated Management Log The server includes an integrated, nonvolatile management log that contains fault and management information.
PAGE 10
1 Illustrated Parts Catalog This chapter provides the illustrated parts breakdown and spare parts lists for the HP ProLiant ML310 server with an Intel Pentium 4 processor. Refer to Table 1-1 and Table 1-2 for the names of referenced spare parts.
PAGE 11
Illustrated Parts Catalog Mechanical Parts Exploded View Figure 1-1: Mechanical parts exploded view 1-2 HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:43 AM
PAGE 12
Illustrated Parts Catalog Mechanical Spare Parts List Table 1-1: Mechanical Spare Parts List Item Description Spare Part Number Chassis 1 Front bezel 287180-001 2 Panel access 307549-001 a) Hood panel (right) b) Access panel (left) Miscellaneous 3 Hardware kit 176618-001 a) Hard drive compartment b) Removable drive tray c) Expansion board knockout d) Hard drive screws 4 Miscellaneous plastics kit 176617-001 a) Expansion board guide b) Rubber bumpers* c) Removable media bezel blank* d) Cable
PAGE 13
Illustrated Parts Catalog Server Components Exploded View (ATA Model) Figure 1-2: Server components exploded view (ATA model) 1-4 HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:43 AM
PAGE 14
Illustrated Parts Catalog Server Components Exploded View (SCSI Model) Figure 1-3: Server components exploded view (SCSI model) HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:43 AM 1-5
PAGE 15
Illustrated Parts Catalog Server Components Spare Parts List Table 1-2: Server Components Spare Parts List Item Description Spare Part Number Mass Storage Devices 5 IDE CD-ROM drive 48X 288894-001 6 Diskette drive 233409-001 7 Hard drive a) 36-GB Wide Ultra3 hard drive, 10K RPM (SCSI model) 177986-001 b) 40-GB ATA hard drive (ATA model) 232008-001 c) 18-GB Wide Ultra3 hard drive, 10K RPM (SCSI model)* 152191-001 Server Components 8 System fan 9 ECC Registered DDR SDRAM DIMM 287179-001
PAGE 16
Illustrated Parts Catalog Table 1-2: Server Components Spare Parts List continued Item Description Spare Part Number 14 CR2032 lithium battery 234556-001 15 Power cable kit 287181-001 a) Power button assembly b) Power shield cable* c) Power extension cable* Miscellaneous 16 17 Enhanced keyboard* 244000-001 a) European keyboard—UK* 244000-031 b) European keyboard—GR* 244000-041 c) European keyboard—FR* 244000-051 d) Spacesaver keyboard—JP* 244000-291 Signal cable kit* 253826-001 a) AT
PAGE 17
2 Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for the HP ProLiant ML310 server. Run the diagnostics program to be sure that all components are operating properly.
PAGE 18
Removal and Replacement Procedures Electrostatic Discharge Information An electrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry. Proper packaging and grounding techniques are necessary precautions to prevent damage. To prevent electrostatic damage, observe the following precautions: 2-2 • Transport products in static-safe containers such as conductive tubes, bags, or boxes. • Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.
PAGE 19
Removal and Replacement Procedures Symbols on Equipment These symbols may be located on equipment in areas where hazardous conditions may exist. This symbol, in conjunction with any of the following symbols, indicates the presence of a potential hazard. The potential for injury exists if warnings are not observed. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel.
PAGE 20
Removal and Replacement Procedures Preparation Procedures WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
PAGE 21
Removal and Replacement Procedures Server Warnings and Precautions WARNING: To reduce the risk of injury from electric shock, disconnect all power cords to completely remove power from the server. WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal server components to cool before touching them. CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating uninterruptible power supply (UPS).
PAGE 22
Removal and Replacement Procedures Front Bezel WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. To remove the front bezel: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2.
PAGE 23
Removal and Replacement Procedures Access Panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal server components to cool before touching them. WARNING: To reduce the risk of personal injury and to prevent damage to the equipment or loss of information, before removing the access panel, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet.
PAGE 24
Removal and Replacement Procedures Storage Devices The ProLiant ML310 server ships standard with seven drive bays, five of which are available. Table 2-1 shows the corresponding drive bay descriptions. Figure 2-3: Storage device drive bay locations Table 2-1: Storage Device Drive Bay Description Drive Position 2-8 Description 1 5.25 x 1.6 inch IDE CD-ROM drive bay 2 5.25 x 1.6 inch removable media drive bay, available 3 5.25 x 1.6 inch removable media drive bay, available 4 5.25 x 1.
PAGE 25
Removal and Replacement Procedures Bezel Blanks To remove a bezel blank from the front bezel: WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded AC outlet. NOTE: It is not necessary to remove a bezel blank when installing a hard drive into a removable media bay. 1. Remove the front bezel.
PAGE 26
Removal and Replacement Procedures System Fan To remove the system fan: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Disconnect the fan power cable from the system board fan connector.
PAGE 27
Removal and Replacement Procedures 4. Use a Torx T-15 screwdriver to remove the four mounting screws from the rear of the server (1). 5. Pull the fan out and away from the chassis (2). Figure 2-6: Removing the system fan To replace the system fan, reverse steps 2 through 5.
PAGE 28
Removal and Replacement Procedures Cable Routing Diagrams Figure 2-7 through Figure 2-9 show cable routing diagrams for the server.
PAGE 29
Removal and Replacement Procedures Figure 2-8: ATA cable routing Table 2-2: ATA Cabling Routing Item Channel/Cable Cable Connector Drive Location 1 ATA/100 RAID primary controller Device 0 Hard drive bay 2 2 ATA/100 RAID secondary controller Device 0 Media bay 3 3 ATA/100 RAID primary controller Device 1 Hard drive bay 3 4 ATA/100 RAID secondary controller Device 1 Media bay 4 HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274
PAGE 30
Removal and Replacement Procedures ATAPI Tape Drive Cable Routing Figure 2-9: ATAPI tape drive cable routing Table 2-3: ATAPI Tape Drive Cable Routing Item 2-14 Connector 1 Integrated IDE channel 2 Device 1 3 Device 0 HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:44 AM
PAGE 31
Removal and Replacement Procedures Drive Tray To remove a drive tray from a removable media bay: WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the access panel, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. NOTE: The drive trays in the removable media bays can be used to mount internal 3.5-inch hard drives.
PAGE 32
Removal and Replacement Procedures Removing a Hard Drive Compartment To remove a hard drive compartment: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Disconnect the power and data cables from the back of all devices in the hard drive compartment being removed.
PAGE 33
Removal and Replacement Procedures 4. Remove the three shipping screws (1), press the tabs on each side of the drive compartment (2), and then pull the drive compartment from the chassis (3). Figure 2-13: Removing a hard drive compartment To replace a hard drive compartment, reverse steps 2 through 4.
PAGE 34
Removal and Replacement Procedures Hard Drives To remove a hard drive from the hard drive compartment: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Disconnect the power and data cables from the back of all devices in the hard drive compartment. 4. Remove the hard drive compartment. Refer to “Removing a Hard Drive Compartment” in this chapter. 5.
PAGE 35
Removal and Replacement Procedures To replace the hard drive: 1. Loosen the four diskette drive screws. They do not need to be removed. Figure 2-15: Loosening the diskette drive screws 2. Slide the drive into the drive bay (1), and then secure it with two screws on each side of the drive compartment (2). 3. Tighten the diskette drive screws (3). 2 3 3 2 1 Figure 2-16: Replacing the hard drive 4. Slide the drive compartment back into the chassis, and then replace the three shipping screws. 5.
PAGE 36
Removal and Replacement Procedures Drive Failure Scenarios IMPORTANT: This section applies only to ATA models of the ProLiant ML310 server. When a drive fails: • Insight Manager notifies you of the drive failure. • If applicable to the operating system, the RAID status icon changes from green to red to indicate that there is a problem. The icon is represented as a round figure wearing sunglasses and is located in the tray bar at the lower right of the screen.
PAGE 37
Removal and Replacement Procedures • If there is not an online spare configured: 1. Power down the server, and then replace the failed drive. 2. Reboot the server. 3. Rebuild the array, choosing one of the following options: a. Run the Integrated ATA RAID Configuration Utility by pressing the F8 key, and then run Rebuild. or b. Let the auto-rebuild take place when the operating system is up and running.
PAGE 38
Removal and Replacement Procedures Array Information IMPORTANT: You cannot add drives or remove drives from an array that has already been configured, without destroying the data present on the already configured array. The Array Information window of the setup screen displays all the drive arrays configured. Use this section to create, delete, or edit the existing configurations. The drive arrays are ® ® displayed as a node in a tree, like Microsoft Windows Explorer.
PAGE 39
Removal and Replacement Procedures — Stripe Size—changes the stripe size. This field applies only to RAID 0 arrays. The default stripe size is 64 KB. IMPORTANT: RAID configurations do not support a stripe size less than 32 KB. You cannot change the stripe size of an array that has been already configured. — Drive Size—displays the size of the array and cannot be edited. If the array type is stripe, then the drive size is the total of all the drives selected.
PAGE 40
Removal and Replacement Procedures Power Switch and LED IMPORTANT: To completely remove all power from the server, you must disconnect the power cord from the server. To remove the power switch: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Disconnect the power switch cable from the system board.
PAGE 41
Removal and Replacement Procedures 4. Remove the LED shield from the front of the chassis by pressing the levers (1), and then pulling the shield away from the chassis (2). Figure 2-18: Removing the LED shield 5. From the front of the chassis, squeeze the sides of the power switch to disengage the two retainer clips from the chassis (1), and then gently remove the power switch from the chassis (2). 6.
PAGE 42
Removal and Replacement Procedures Removing a Device from a Removable Media Bay To remove a device from a removable media bay: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Disconnect the power and data cables from the back of the device. 4. Remove the screws from the front of the removable tray (1). 5. Remove the removable media tray from the chassis (2).
PAGE 43
Removal and Replacement Procedures 6. Remove the screws from the bottom of the device (1). 7. Remove the device from the tray (2). Figure 2-21: Removing a device from the removable media bay To replace a removable media bay device, reverse steps 2 through 7. Refer to Figure 2-15 to locate the hard drive screws.
PAGE 44
Removal and Replacement Procedures Expansion Slots Figure 2-22 and Table 2-4 identify the expansion slot locations. Figure 2-22: Expansion slot locations Table 2-4: Expansion Slot Locations Item 2-28 Description Slot Number 1 3.3-volt, 33-MHz, 64-bit PCI slot 1 2 3.3-volt, 33-MHz, 64-bit PCI slot 2 3 3.3-volt, 33-MHz, 64-bit PCI slot 3 4 3.
PAGE 45
Removal and Replacement Procedures Removing an Expansion Slot Retainer To remove an expansion slot retainer: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Release the expansion board retainer by loosening the screw (1) and pivoting the retainer back towards the front of the chassis (2).
PAGE 46
Removal and Replacement Procedures Expansion Board Guide To remove the expansion board guide: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Remove all expansion boards supported by the board guide. 4. Push in the four locking tabs (1), and then pull the guide back and away from the chassis (2).
PAGE 47
Removal and Replacement Procedures Memory Modules The server supports ECC Registered PC2100 DDR SDRAM DIMMs. Additional DIMMs are available to upgrade the memory. The server has four DIMM sockets located on the system board. NOTE: The server supports PC2100 memory, which runs at full speed with a 533-MHz front side bus CPU, and runs at PC1600 speed with a 400-MHz front side bus CPU. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
PAGE 48
Removal and Replacement Procedures Removing a Memory Module To remove a memory module: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Press outward on both latches of the memory module socket at the same time (1) to release the DIMM and push it partially out of the socket. 4. Lift the memory module from the socket (2).
PAGE 49
Removal and Replacement Procedures Processor Socket ® ® The server comes standard with an Intel Pentium 4 processor.
PAGE 50
Removal and Replacement Procedures Processor and Heatsink with CPU Fan Assembly To remove the heatsink and processor: CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded (earthed) before beginning any installation procedure. Refer to “Electrostatic Discharge Information” in this chapter for more information. CAUTION: To reduce the risk of personal injury from hot surfaces, allow the internal server components to cool before touching them. 1.
PAGE 51
Removal and Replacement Procedures 5. Push down on the retainer clip levers, and then pull up to remove the levers from the heatsink/CPU fan assembly. Figure 2-29 illustrates one side of the heatsink/CPU fan assembly. Figure 2-29: Removing the levers from the heatsink/CPU fan assembly 6. Lift the heatsink from the processor.
PAGE 52
Removal and Replacement Procedures 7. Raise the processor socket lever (1). IMPORTANT: The processor socket lever must be perpendicular to the system board to unlock the processor unit. 8. Lift the processor out of the socket (2). Figure 2-31: Removing the processor 9. Lower the processor socket lever. 10. Reinstall the access panel and the bezel. To replace the processor, reverse steps 2 through 10.
PAGE 53
Removal and Replacement Procedures System Board CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded (earthed) before beginning any installation procedure. Refer to “Electrostatic Discharge Information” in this chapter for more information. To remove the system board: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3.
PAGE 54
Removal and Replacement Procedures Power Supply To remove the power supply: WARNING: To reduce the risk of electric shock or damage to the equipment: • Unplug the power cord before removing the power supply from the server. • Install the power supply before connecting the power cord to the power supply. CAUTION: To avoid dropping the power supply, pull out and hold the power supply with a firm grip. 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2.
PAGE 55
Removal and Replacement Procedures Battery The server has nonvolatile memory, which requires a battery to retain server information. The battery is located on the system board. Replacing the Battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. When replacing the battery, use a 3-volt CR2032 lithium battery.
PAGE 56
Removal and Replacement Procedures To replace the lithium battery on the system board: 1. Complete the preparation procedures. Refer to “Preparation Procedures” in this chapter. 2. Remove the access panel. Refer to “Access Panel” in this chapter. 3. Locate the battery on the system board. NOTE: If you have expansion boards installed, it may be necessary to remove them to gain access to the battery. 4.
PAGE 57
Removal and Replacement Procedures IMPORTANT: Positive (+) polarity must be positioned up. 5. Slide the replacement battery into the proper position with the positive (+) side up. 6. Replace the server access panel and connect cables to the server. 7. Run RBSU to reconfigure the server by pressing the F9 key when prompted during server startup. Refer to the ROM-Based Setup Utility User Guide for more information on RBSU.
PAGE 58
3 Diagnostic Tools This chapter provides an overview of the software and firmware diagnostic tools available for the HP ProLiant ML310 server.
PAGE 59
Diagnostic Tools Diagnostic Tools Utility Overview The following utilities were developed to assist in diagnosing problems, testing the hardware, and monitoring and managing the ProLiant ML310 server hardware. Table 3-1: Diagnostic Tools Tool What it is How to run it HP Diagnostics Utility Utility to assist testing and/or verifying operation of HP hardware. If problems are found, HP Diagnostics isolates failures down to the replaceable part whenever possible.
PAGE 60
Diagnostic Tools Table 3-1: Diagnostic Tools continued Tool What it is How to run it SmartStart software Located on the SmartStart CD, SmartStart is the intelligent way to set up the HP server. The SmartStart CD is used to load the system software, thereby achieving a well-integrated server and ensuring maximum dependability and supportability. The SmartStart CD contains diagnostic utilities and ROMPaq tools. Power up from the SmartStart CD.
PAGE 61
Diagnostic Tools Table 3-1: Diagnostic Tools continued Tool What it is How to run it Automatic Server Recovery (ASR) A tool that lets the server restart automatically after a catastrophic operating system failure, including software errors, OS lockups, environmental abnormalities, and some hardware errors. This tool is a function of the hardware/software system through RBSU. Be sure that this tool is enabled through RBSU. The systems management drive must be loaded to activate ASR.
PAGE 62
Diagnostic Tools For More Information For detailed information about each of these diagnostic tools, refer to the HP Servers Troubleshooting Guide on the Documentation CD. For the most recent version of this guide, refer to the Reference Library on the HP ProLiant ML310 page at www.hp.
PAGE 63
4 Connectors, Switches, and LEDs This chapter contains illustrations and tables identifying connectors, switches, and LED locations on the system board and rear panel for the HP ProLiant ML310 server.
PAGE 64
Connectors, Switches, and LEDs Connectors This section contains graphics and tables identifying connector and component locations on the system board and rear panel of the server. System Board Components Figure 4-1 and Table 4-1 identify the SCSI system board components for the server.
PAGE 65
Connectors, Switches, and LEDs Table 4-1: SCSI System Board Components Item Component Item Component 1 Power supply connectors 14 64-bit PCI expansion slot 1 2 Power switch assembly connector 15 NMI switch 3 Diskette drive connector 16 System fan connector 4 IDE connector (ATAPI devices) 17 CPU fan connector 5 DIMM slots 18 Processor socket 6 CR2032 battery 19 Keyboard connector 7 SCSI connector 20 Mouse connector 8 System configuration switch 21 Parallel port 9 RIB 30-
PAGE 66
Connectors, Switches, and LEDs ATA System Board Figure 4-2 and Table 4-2 identify the ATA system board components for the server.
PAGE 67
Connectors, Switches, and LEDs Table 4-2: ATA System Board Components Item Component Item Component 1 Power supply connectors 15 64-bit PCI expansion slot 1 2 Power switch assembly connector 16 NMI switch 3 Diskette drive connector 17 System fan connector 4 IDE connector (ATAPI devices) 18 CPU fan connector 5 DIMM slots 19 Processor socket 6 ATA/100 RAID primary connector 20 Keyboard connector 7 ATA/100 RAID secondary connector 21 Mouse connector 8 CR2032 battery * 22 Par
PAGE 68
Connectors, Switches, and LEDs Rear Panel Connectors Figure 4-3 and Table 4-3 identify the rear panel connectors for the server.
PAGE 69
Connectors, Switches, and LEDs Internal SCSI Components Figure 4-4: Internal SCSI components Table 4-4: Internal SCSI Components Item Description 1 Removable media bay area 2 Hard drive bay area 3 Internal SCSI connector A HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:46 AM 4-7
PAGE 70
Connectors, Switches, and LEDs Internal ATA Components Figure 4-5: Internal ATA components Table 4-5: Internal ATA Components Item 4-8 Description 1 Removable media bay area 2 Hard drive bay area 3 ATA/100 primary controller 4 ATA/100 secondary controller HP ProLiant ML310 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Son of Beast Part Number: 274429-005 Last Saved On: 4/16/03 8:46 AM
PAGE 71
Connectors, Switches, and LEDs Switches The server contains two switchbanks. This section explains the use of each reserved and nonreserved switch. System Configuration Switch Figure 4-6 and Table 4-6 identify the system configuration switch default settings for the server.
PAGE 72
Connectors, Switches, and LEDs Table 4-6: System Configuration Switch Default Settings Position Default Description Settings 1 Off Reserved N/A 2 Off Lock configuration Off = Normal operation On = Configuration changes cannot be made 3 Off Tower/rack configuration Off = Tower configuration On = Rack configuration 4 Off Diskette boot Off = Observe RBSU diskette boot selection On = Override RBSU setting and allow diskette boot selection 5 Off Password disable Off = Enable password prom
PAGE 73
Connectors, Switches, and LEDs System ID Switch Settings Figure 4-7 and Table 4-7 identify the system ID switch settings for the server.
PAGE 74
Connectors, Switches, and LEDs LEDs This section contains graphics information on the following LEDs: • Server LEDs (on the front of the server) • System board LEDs • Network controller LEDs (on the back of the server) Server LEDs Figure 4-8 and Table 4-9 identify the LED locations on the front of the server.
PAGE 75
Connectors, Switches, and LEDs Table 4-8: Server LEDs Item Description Status 1 Power button N/A 2 Power On/Standby LED Green = Server on, AC power OK. Do not remove power from server. Flashing green = Server sleeping. Do not remove power from the server. Amber = Server in standby mode. AC power OK. Off = Server off, no AC power. 3 Hard drive LED On or flashing = A hard drive is being accessed. Off = No hard drive is currently being accessed.
PAGE 76
Connectors, Switches, and LEDs System Board LEDs Figure 4-9 and Table 4-9 identify the system board LEDs for the server.
PAGE 77
Connectors, Switches, and LEDs Table 4-9: System Board LEDs Item 1 Description Status 4-pin power connector Off = Processor installed. Amber = Processor not installed. 2 Second 4-pin power connector Off = Power connector installed. Amber = Power connector not installed. 3 AC power Off = The AC power cord is not plugged into the power supply or the power supply failed. Green = Power supply is on and functioning. 4 CPU 1 pre-failure or failure Off = CPU functioning.
PAGE 78
Connectors, Switches, and LEDs Network Controller LEDs Figure 4-10 and Table 4-10 identify the network controller LEDs for the server.
PAGE 79
5 Physical and Operating Specifications This chapter provides specifications for the HP ProLiant ML310 server. The following specifications are provided: • Server unit • Memory • 3.
PAGE 80
Physical and Operating Specifications Server Unit Table 5-1: Server Unit Specifications Specification Value Dimensions Height 42.0 cm (16.5 in) Width 19.1 cm (7.5 in) Depth 48.5 cm (19.1 in) Approximate weight 18.18 kg (40 lb) weight approximate, depending upon options International input requirements (per power supply) Rated input voltage 200 VAC to 240 VAC Rated input frequency 50 Hz to 60 Hz Rated input current <8 A RMS at 90 VAC with maximum load U.S.
PAGE 81
Physical and Operating Specifications Memory Table 5-2: Memory Specifications Specification Value Size 64 MB, 128 MB, 256 MB, and 512 MB, and 1 GB Speed DDR 200/266 MHz Type ECC Registered PC2100 DDR SDRAM DIMMs Diskette Drive Table 5-3: 1.44-MB Diskette Drive Specifications Specification Value Size 8.89 mm (3.5 in) LEDs (front panel) Green Read/write capacity per diskette (high/low density) 1.
PAGE 82
Physical and Operating Specifications IDE CD-ROM Drive Table 5-4: IDE CD-ROM Specifications Specification Value Applicable disk CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA; Photo CD (single- and multiple-session), CD-XA (mode 2, forms 1 and 2); CDI ready; CD-WO Capacity 650 MB Rotational speed 5,200 rpm Block size 2,328 bytes (CD-XA) 2,340 bytes, 2,336 bytes, 1,024 bytes (mode 2) 2,048 bytes, 1,024 bytes (mode 1) 2,352 bytes (CD-DA) Dimensions Height 42.9 mm (1.
PAGE 83
Physical and Operating Specifications Table 5-4: IDE CD-ROM Specifications continued Specification Value Output power 0.14 mW Operating conditions Temperature 5°C to 45°C (41°F to 113°F) Humidity 5% to 90% (10% to 80%) ATA Hard Drives Table 5-5: ATA Hard Drive Specifications Description 80 GB 7.2K rpm 40 GB 7.2K rpm Capacity 80,020.0 MB 40,020.0 MB Height 26.1 mm (1.028 in) 26.1 mm (1.028 in) Width 101.6 mm (4 in) 101.
PAGE 84
Physical and Operating Specifications Wide Ultra3 SCSI Hard Drives Table 5-6: Wide Ultra3 SCSI Hard Drive Specifications Description 18.2 GB 10 K rpm 36.4 GB 10 K rpm Capacity 18,209.3 MB 36,419.2 MB Height 25.4 mm (1 in) 25.4 mm (1 in) Width 101.6 mm (4.0 in) 101.6 mm (4.0 in) Interface Wide Ultra3 SCSI Wide Ultra3 SCSI Transfer rate synchronous (max) 160 MBps 160 MBps Single track 0.7 ms 0.7 ms Average 5.4 ms 5.4 ms Full stroke 11.0 ms 11.
PAGE 85
Physical and Operating Specifications Integrated 10/100/1000 Wake on LAN Network Interface Controller Table 5-7: Integrated 10/100 Wake on LAN NIC Specifications Specification Value Network interface 1000Base-T/100Base-TX/10Base-T Compatibility IEEE 802.3am, 802.3u, 802.3 Data transfer method 32-bit, 33-MHz PCI bus master Network transfer rate 10/100/1000 MBps Connector RJ-45 Compliance PCI 2.2 OS support For specific OS support, refer to www.hp.
PAGE 86
Physical and Operating Specifications Integrated Dual-Channel Ultra ATA 100 Controller Table 5-9: Integrated Dual-Channel Ultra ATA 100 Controller Specifications Specification Value Protocol UDMA Mode (0-5) PIO Mode (0-4) 5-8 Drives supported Up to 4 ATA (2 devices per channel) Data transfer method 32-bit/33-MHz PCI bus-master Maximum transfer rate per PCI Bus (peak) 133 MBps per channel ATA 100 Cable 80-conductor cable ATA channel transfer rate 100 MBps per channel ATA connectors Two 40-pi
PAGE 87
Index A access panel part number 1-3 removing 2-7 replacing 2-7 access times CD-ROM drive 5-4 diskette drive 5-3 ASR (Automatic Server Recovery), running 3-4 ATA cable assembly, part number 1-7 ATA ribbon cable assembly, part number 1-7 ATAPI tape drive cabling 2-14 Automatic Server Recovery See ASR B battery function of 2-39 location on system board 4-3, 4-5 part number 1-7 replacing 2-40 bezel blank part number 1-3 removing 2-9 replacing 2-9 C cable clips, part number 1-3 CD-ROM drive part number 1-6 s
PAGE 88
Index expansion board guide part number 1-3 removing 2-30 replacing 2-30 expansion board knockout, part number 1-3 expansion board retainer, replacing 2-29 expansion slot, locations 2-28 Integrated ATA RAID Configuration Utility Array Information window 2-22 described 3-4 exiting 2-23 Help window 2-22 Physical Drive Information window 2-22 running 3-4 IRQ conflict, resolving 3-3 F J fan part number 1-6 removing 2-10 replacing 2-11 floppy drive See diskette drive front bezel part number 1-3 removing 2-6
PAGE 89
Index N S network interface controller (NIC), specifications 5-7 NIC See network interface controller screwdriver symbol 2-3 SCSI cable routing 2-12 seek time, hard drive 5-5, 5-6 serial port connectors 4-3, 4-5 server components exploded view (ATA model), illustrated 1-4 exploded view (SCSI model), illustrated 1-5 spare parts list 1-6, 1-7 server LEDs 4-13 server specifications 5-1 signal cable kit, part number 1-7 single-channel Wide Ultra3 SCSI controller, specifications 5-7 SmartStart 3-3 SmartStart
PAGE 90
Index RBSU (ROM-Based Setup Utility) 2-41, 3-3 ROMPaq 3-3 SmartStart 3-3 SmartStart Diskette Builder 3-3 Survey Utility 3-2 T technician notes vii technician notes, warning 2-4 telephone numbers ix telephone symbol 2-3 tools required for service procedures 2-1 type recommended 2-2 tower-to-rack option kit, part number 1-7 V ventilation clearances viii W U Ultra ATA 100 controller, specifications 5-8 Ultra3 SCSI cable, part number 1-7 USB port connectors 4-3, 4-5 utilities ASR (Automatic Server Recovery)