Technical data

INITIALIZE command (cont’d)
creating volume identifiers for continuation
volumes, Vo l 1, 9–54
disk volumes, Vo l 1 , 9–17
for formatting page and swap file disks during
system startup, Vo l 1 , 5–6
mounting volume sets, Vo l 1 , 9–54
qualifiers, Vo l 1, 9–18
setting device protection, Vo l 1 , 9–23
for tape volumes, Vo l 1 , 10–22, 10–31
specifying logical names, Vo l 1 , 10–31
to format and write label to volume, Vo l 1 ,
9–18
Initializing
queues, Vo l 1 , 14–15
See also INITIALIZE/QUEUE command
volumes
See also INITIALIZE command
assisting users, Vo l 1 , 9–21
disk volumes, Vo l 1 , 9–16, 9–19
ODS-5 format, Vo l 1 , 9–20
results of, Vo l 1 , 11–14
tape volumes, Vo l 1 , 10–14
INITIAL phase of system startup, Vo l 1 , 5–4,
5–18
Initial System Load
See ISL
Input an existing PCF, Vol 1 , 3–26
Input files
relative versions
BACKUP supports, Vo l 1 , 11–6
Input symbiont for card reader
running interactively, Vo l 1 , 8–40
Installation and upgrade information
Alpha only
problems and restrictions
tuning BAP system parameters, Vo l 2 ,
15–37
Installation procedures
See also Installing software; VMSINSTAL.COM
command procedure
completing, Vo l 1, 3–9
INSTALL command
in SYSGEN, Vo l 2 , 16–26
in system startup, Vo l 1 , 5–7
Installed files
See Known images
Installing images, Vo l 2 , 17–15
See also Install utility; Known images
effect on RUN command, Vo l 2 , 17–9
in SYSTARTUP_VMS.COM, Vo l 1 , 5–13; Vo l
2, 17–9
reasons for, Vo l 2 , 17–8
to improve system performance, Vo l 2, 17–7,
17–9
Installing page and swap files
in system startup, Vo l 1 , 5–6; Vo l 2 , 16–6,
16–26, 16–27
with AUTOGEN, Vo l 2 , 16–29
with SYPAGSWPFILES.COM command
procedure, Vo l 2, 16–26
with SYSGEN, Vo l 2 , 16–26
Installing software
See also Installation procedure
as a batch job, Vol 1 , 3–29
completing procedure, Vo l 1 , 3–9
creating a new PCF during, Vo l 1, 3–26
deinstalling software, Vo l 1 , 3–31
logging file activity, Vo l 1 , 3–13
managing installed software, Vo l 1 , 3–31
multiple products at once, Vo l 1 , 3–25
noncompliant products, Vo l 1 , 3–23
on alternate disk, Vo l 1 , 3–9
preparing for installation, Vo l 1 , 3–3
reconfiguring product options, Vo l 1 , 3–29
removing installed software, Vo l 1 , 3–31
responding to questions during installation, Vo l
1, 3–26
specifying source and destination locations, Vo l
1, 3–25
supplying answers from a PCF, Vo l 1, 3–26
tracking dependencies, Vo l 1 , 3–24
using a PCF for consistency, Vo l 1, 3–19
Install utility (INSTALL)
See also Installing images; Known images
and version checking, Vo l 1 , 5–23
determines content of address data section, Vo l
2, 17–12
determining number frequency of image use,
Vo l 2 , 17–11, 17–16
improving system performance, Vo l 2, 17–7,
17–8, 17–9
listing number of concurrent file accesses, Vol
2, 17–7
making images header resident, Vo l 2 , 17–10,
17–11
making images privileged, Vol 2 , 17–10, 17–13
permanently open images, Vo l 2 , 17–10, 17–11
reasons for using, Vo l 2 , 17–8
Interactive identifiers, Vo l 1 , 12–11
Interactive users
limiting for performance management, Vo l 2 ,
17–4
limiting in system startup, Vol 1 , 5–16
Interchange environment
protection, Vo l 1, 9–27
Interfaces to POLYCENTER Software Installation
utility
DCL, Vo l 1, 3–14
Interfaces to the Backup utility, Vo l 1, 11–5
Index–23