Notice The information in this guide is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation.
CONTENTS chapter 1 TAKING A LOOK AT THE COMPUTER Pointing Device Components..........................................................1-1 Top Components .............................................................................1-2 Left Side Components.....................................................................1-3 Right Side Components...................................................................1-4 Front Components ...........................................................................
Changing an Easy Access Button Name or Assignment Within a Scheme .................................................. 2-11 Displaying or Selecting an Easy Access Button Scheme .................................................... 2-12 Deleting an Easy Access Button Scheme................................. 2-12 Using the Embedded Numeric Keypad ........................................ 2-13 Toggling the Keypad On and Off.............................................
Calibrating a Battery Pack.............................................................4-10 Checking the Calibration of a Battery Pack..............................4-11 Running a Calibration ...............................................................4-12 Stopping a Calibration ..............................................................4-12 Setting Power Preferences.............................................................4-13 Setting Power Preferences in Windows 95...............................
CD-ROM and DVD-ROM Drives .................................................. 5-8 Removing a CD-ROM Drive or DVD-ROM Drive ................... 5-8 Inserting a CD-ROM Drive or DVD-ROM Drive ..................... 5-9 Inserting a Disc into a CD-ROM Drive or DVD-ROM Drive ..................................................................... 5-10 Removing a Disc from a CD-ROM Drive or DVD-ROM Drive .....................................................................
Using DriveLock ...........................................................................6-11 Protecting a Hard Drive with DriveLock..................................6-12 Accessing a Protected Hard Drive ............................................6-13 Changing a DriveLock Password or Removing DriveLock Protection from a Drive ........................6-13 Disabling a Device ........................................................................6-14 Enabling or Disabling a Device in Computer Setup........
Reinstalling Modem Drivers (Windows 2000 Professional) .................................................. 7-13 chapter 8 CONNECTING TO A LOCAL AREA NETWORK Connecting to a LAN ...................................................................... 8-2 Turning a LAN Connection On and Off ......................................... 8-2 Accessing the Network at Startup................................................... 8-3 Reinstalling or Updating Drivers (Windows 95 or Windows 98)...............................
chapter 10 USING AUDIO AND VIDEO FEATURES Using the Internal Microphone and the Internal Speakers............10-1 Connecting an External Audio Device..........................................10-2 Selecting an Audio Connector ..................................................10-2 Connecting a Device to the Microphone Jack ..........................10-2 Connecting a Device to the Stereo Speaker/Headphone Jack ...............................................10-3 Adjusting Volume ...............................
chapter 14 COMPUTER SETUP AND DIAGNOSTICS UTILITIES Selecting Computer Setup or Compaq Diagnostics...................... 14-1 Using Computer Setup.................................................................. 14-2 Selecting from the File Menu................................................... 14-2 Selecting from the Security Menu............................................ 14-3 Selecting from the Advanced Menu......................................... 14-4 Using Compaq Diagnostics ......................
appendix A COMPAQ CUSTOMER SUPPORT Using the Compaq Support Forum.................................................A-1 Preparing to Call Technical Support ..............................................A-1 Worldwide Telephone Numbers ....................................................A-2 appendix B REGULATORY NOTICES .............................................................................B-1 appendix C ELECTROSTATIC DISCHARGE Preventing Electrostatic Discharge ........................................
chapter 1 T AKING A L OOK AT THE C OMPUTER Pointing Device Components Pointing Device Components Component Function Moves the pointer. 1 Pointing stick 2 Left and right pointing-stick Function like the left and right buttons buttons (pointing-stick models only) on an external mouse. 3 Scroll pointing-stick button Can be set to scroll, magnify, or (pointing-stick models only) function like the scroll button on an external mouse.
Top Components Top Components Component Function 1 Display switch Turns off the computer display if the computer is closed while on. 2 Suspend button* Initiates and exits Suspend.** When pressed with the Fn key, initiates Hibernation. 3 Hard drive light On: The primary hard drive is being accessed. 4 MultiBay drive light On: A drive in the MultiBay or the external diskette drive bay is being accessed.
Top Components Continued Component Function < Power switch Turns the computer on or off or exits Suspend.** = Windows application key Displays a shortcut menu for item beneath the pointer. > Internal speakers ? Microsoft logo key Produce stereo sound. Displays Windows Start menu. *In Windows 98 the term sleep button replaces the term suspend button. **In Windows 98 and Windows 2000 Professional the term Standby replaces the term Suspend.
Right Side Components Right Side Components Component Description 1 PC Card eject buttons Top button: Ejects a PC Card from the top PC Card slot. Bottom button: Ejects a PC Card from the bottom PC Card slot. Allows airflow needed to cool computer components. Do not block airflow. (2) 2 Airflow vent 3 PC Card slots (2) Support 32-bit (CardBus) and 16-bit PC Cards. 4 Acoustic vent Allows airflow needed to cool sound components. Do not block airflow. Supports MultiBay devices.
Front Components Front Components Component 1 Hard drive bay 2 Stereo speaker/ headphone jack Description Holds the primary hard drive. Connects external speakers, headphones, headset, or television audio. 3 Microphone jack Connects a single sound channel microphone. 4 Power/suspend light On: Power is turned on. Off: Power is turned off. Blinking: Computer is in Suspend.* 5 Battery light On: A battery pack is charging.
Rear Panel Components Rear Panel Components Component Description 1 Infrared port Links another IrDA-compliant device for wireless communication. Connects a serial device. 2 Serial connector 3 External monitor connector Connects an external monitor or overhead projector. 4 Docking connector Connects the computer to a docking base. 5 Parallel connector Connects the external diskette drive assembly or 6 Power connector 7 USB connector 8 Keyboard/mouse connector another parallel device.
Bottom Components Bottom Components Component Description 1 Battery bay 2 Modem slot cover 3 Modem agency Covers the modem compartment. approvals label (internal modem models only) 4 MultiBay notch Holds the primary battery. Lists the countries in which the modem has been approved for use. You may need this information to use the modem while traveling. Helps you remove a drive or battery pack from the MultiBay. 5 MultiBay release latch Releases a removable drive or battery pack from the MultiBay.
Additional Standard Components The components included with the computer vary by geographic region and the computer hardware configuration ordered. The following illustration and table identify the standard components included with most computer models. NOTE: Some components, such as the hard drive and the primary battery pack, ship inside computer bays identified in previous sections and are not included in this illustration.
Additional Standard Components Component Function 1 Weight saver Can replace a MultiBay device to protect the MultiBay and reduce computer weight. 2 Power cord Connects the AC Adapter to an AC electrical outlet. 3 AC Adapter 4 3-to-2-prong plug Converts AC power to DC power. 5 Compaq Portable Contains: adapter (Japan only) Product Reference Library CD-ROM Adapts the power cord to a 2-prong electrical outlet. ■ Reference Guide. ■ Modem Commands. ■ Safety & Comfort Guide.
chapter 2 U SING THE K EYBOARD Using the Pointing Device The pointing stick (pointing-stick models) and the TouchPad (TouchPad models) function with any software that supports a Microsoft-compatible mouse. NOTE: For software that does not support a Microsoft-compatible mouse, open Computer Setup, select Advanced!Device Options, then select the Disable Multiple Pointing Devices checkbox.
Identifying Keyboard Components (TouchPad Models) 1 TouchPad 3 Right TouchPad button 2 Left TouchPad button Navigating with the Pointing Device Pointing-Device Procedures Task Procedure Move the pointer Pointing stick: Directionally press the pointing stick. TouchPad: Move your finger directionally across the TouchPad surface. Increase or decrease Pointing stick: Increase or decrease the pointer speed as you move pressure on the pointing stick. the pointer.
Pointing-Device Procedures Continued Task Procedure Highlight an item.* Position the pointer at the item to be highlighted. Quickly tap the pointing stick or TouchPad once, then hold down on the pointing stick or TouchPad as you move the pointer over the item. Select text or an object.* Position the pointer over the highlighted text or object, then quickly tap the pointing stick or TouchPad once. Activate a selection.
Using the Fn Key Many commands are entered by pressing the Fn key and another key simultaneously. For example, Hibernation is initiated by pressings Fn + the suspend button, and most of the hotkey commands in the following section are entered by pressing Fn + a function key. If you enable sequential Fn + commands, all commands that can be entered by pressing the Fn key and a second key simultaneously can also be entered by pressing Fn and the second key sequentially.
Using Hotkeys Hotkeys are preset combinations of the Fn key 1 plus a second key that access or execute frequently used system functions. The icons on the function keys F4 to F10 2 represent these functions. ■ To close a window opened with hotkeys, use standard Windows procedures or press the hotkeys again. ■ To use hotkeys on an external keyboard, which does not have an Fn key, press the Scroll Lock key twice, then the second key only of the hotkey combination.
Switching the Display and Image (Fn+F4) In Windows 95, Windows NT 4.0, or Windows 2000 Professional—Toggle Fn+F4 to switch the image among the computer display, external display(s), and simultaneous display. The external displays can be connected through the external monitor connector or the composite video-out jack. In Windows 98— ■ When MultiMonitor is enabled, press Fn+F4 to turn off an external display connected to the external monitor connector and disable MultiMonitor.
Setting a Power Conservation Level (Fn+F7) In Windows 98 or Windows 2000 Professional—Press Fn+F7 to open the Power Schemes window. In Windows 95 or Windows NT 4.0—Press Fn+F7 to open the Battery Conservation Settings window. ■ To select a preset battery conservation level, choose among ❏ High—Maximizes running time from a single charge. ❏ Medium—Balances system performance with running time. ❏ None (Drain)—Runs the computer at full power.
Using the Easy Access Buttons Each Easy Access Button on the computer keyboard or on an optional external keyboard can be assigned to open an item on the Internet, a network, or a drive with a single keystroke. Internet and Network Connection Requirements for Using Easy Access Buttons Easy Access keys can access an item on the Internet or a network only after your Internet or network services have been set up.
Easy Access Buttons Button Icon Default Name and Assignment 1 Armada Information Page—Links directly to Compaq Armada user information for quick answers to your computer questions. 2 MyArmada—Opens a personal Internet web page that you can customize with items such as local weather, news, sports, and financial information. 3 Search—Opens the AltaVista search engine website, which helps you find information on the Internet. 4 Email—Accesses your default email application.
Adding an Easy Access Button Scheme Button assignments are grouped into schemes, which you create or specify as you change the assignments of individual buttons. ■ Buttons can be renamed or reassigned within any scheme except the default scheme. ■ You can create an unlimited number of schemes. ■ Each button can have the same or different names and assignments in different schemes.
7. Repeat steps 4 to 6 for each Easy Access Button you want to include in the new scheme. 8. Select the Apply or OK button. Changing an Easy Access Button Name or Assignment Within a Scheme NOTE: To change more than one button name or assignment within a scheme, repeat steps 3 to 5 for each button being reassigned. 1. Double-click the Easy Access Buttons icon on the Windows taskbar. or Click Start!Settings!Control Panel. Double-click the Keyboard icon, then select the Easy Access Buttons tab. 2.
Displaying or Selecting an Easy Access Button Scheme 1. Double-click the Easy Access Buttons icon on the Windows taskbar. or Click Start!Settings!Control Panel. Double-click the Keyboard icon, then select the Easy Access Buttons tab. 2. The name of the currently active scheme is displayed in the Scheme box. To change to a different scheme, select the name of the scheme you want to make active from the drop-down list in the Scheme box. 3. Select the Apply or OK button.
Using the Embedded Numeric Keypad Toggling the Keypad On and Off To convert the embedded numeric keypad section 1 of the keyboard to a keypad—Press Fn+Num Lk 2. When the embedded numeric keypad is enabled, the characters upper-right on the keypad keys are active and the num lock light 3 is on. To disable the embedded numeric keypad—Press Fn+Num Lk. NOTE: The embedded numeric keypad cannot be enabled while an optional external keyboard or numeric keypad is connected to the computer.
Enabling the Keypad at Startup To set the computer to start up with the embedded numeric keypad enabled— 1. Turn on or restart the computer, then press F10 when the blinking cursor appears upper-right on the screen. ❏ To change the language, press F2. ❏ For navigation instructions, press F1. 2. Select Advanced!Device Options, then press Enter. 3. Toggle on the Num Lock State at Boot field, then press F10. 4.
chapter 3 I NSERTING , R EMOVING , OR S TORING A B ATTERY P ACK Selecting a Battery Pack Location The computer supports up to two battery packs. ■ The battery pack included with the computer can be used only in the battery bay. The battery pack in the battery bay is the primary battery pack. ■ An optional MultiBay battery pack can be used only in the MultiBay. Multiple battery packs in the system charge and discharge by location in a preset sequence.
Storing a Battery Pack CAUTION: To prevent damage to a battery pack, do not expose it to high temperatures for extended periods of time. If the computer will be unused and unplugged from an external power source for more than 2 weeks, remove and store the battery pack(s). Proper storage procedures reduce the self-discharge rate of a battery pack. Store a battery pack in a cool, dry place within the following temperature ranges.
Removing a Primary Battery Pack from the Battery Bay 1. If a battery pack is your only power source, initiate Hibernation by pressing Fn + the suspend button. NOTE: If there is drive activity, Hibernation may not occur instantly. 2. Close the display. 3. Tilt the computer up 1 and push the battery release latch below the battery bay toward the fan 2 to release the battery pack. 4. Remove the battery pack from the battery bay 3.
Inserting a Primary Battery Pack into the Battery Bay 1. Close the display. 2. Tilt the computer up 1. 3. With the smooth side of the battery pack facing up and the battery cells facing in, lead the rounded edge of the battery pack into the battery bay. Angle the battery pack into the bay until it is fully seated 2. 4. If the computer is in Hibernation, slide the power switch to resume normal operation.
Removing a MultiBay Battery Pack from the MultiBay 1. If a battery pack is your only power source, initiate Hibernation. 2. With the MultiBay facing you, tilt the computer up 1 and slide the MultiBay release latch toward the opening of the bay 2. 3. Grasp the edge of the battery pack at the notch under the battery pack and pull it out of the MultiBay 3.
Inserting a MultiBay Battery Pack into the MultiBay 1. With the battery pack charge level lights facing up and the battery contacts facing in, insert the battery pack into the MultiBay. 2. If the computer is in Hibernation, slide the power switch to resume normal operation. 3-6 Inserting, Removing, or Storing a Battery Pack COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Karen Williams Saved date: 05/30/00 10:33 AM Part Number: 168893-001 File name: CH03.
chapter 4 M ANAGING P OWER Selecting a Power Source Task Work within installed applications. Power Source ■ Charged battery pack in the computer or ■ External power supplied through one of the following devices: ❏ AC Adapter ❏ Optional docking base ❏ Optional Automobile Power Adapter/Charger ❏ Optional Charge or calibrate a battery pack in the computer.
Using Suspend and Hibernation Suspend Suspend is an energy-saving feature that conserves power and reduces startup time. Suspend, called Standby in Windows 98, reduces power to system components that are not being used. Suspend can be initiated by you or by the system. When Suspend is initiated, your work is saved in random access memory (RAM) and the screen is cleared. When you resume work, your information returns to the screen where you left off.
Suspend, Hibernation, and Shutdown Procedures All components mentioned in this table are identified in the section immediately following the table. Suspend, Hibernation, and Shutdown Procedures Task Procedure Result Turn the Slide power switch. computer on or from Press suspend shutdown. button.* Power/suspend light turns on. Shut down the computer. Power/suspend light turns off. Initiate Suspend.** Shut down the computer as directed by your operating system documentation. Operating system loads.
Identifying Power Controls and the Power/Suspend Light 1 Fn key 2 Suspend button 3 Power switch 4 Power/suspend light 4-4 Managing Power COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Integrity Group Saved date: 06/01/00 10:23 AM Part Number: 168893-001 File name: CH04.
Managing Low-Battery Conditions Identifying Low-Battery Conditions Low-Battery Condition When a battery pack that is the only source of power available to the computer reaches a low-battery condition ■ The system beeps 5 times. ■ The battery light 1 blinks. Critical Low-Battery Condition If a low-battery condition is not resolved, the computer enters a critical low-battery condition.
Resolving Low-Battery Conditions When External Power Is Available Select one of the following options, depending on your situation: ■ Connect the computer to an electrical outlet with the AC Adapter. ■ Dock the computer in a docking base that is connected to external power. ■ Plug an optional Automobile Power Adapter/Charger into the computer and into a vehicle cigarette lighter receptacle.
Charging a Battery Pack To charge a battery pack in the computer, supply external power to the computer through the AC Adapter, an optional docking base, or an optional Automobile Power Adapter/Charger. NOTE: An optional Aircraft Power Adapter does not charge a battery pack. Charging may be delayed if a battery pack is new, has not been used for 2 weeks or more, or is much warmer or cooler than room temperature.
Monitoring the Charge in a Battery Pack Increasing the Accuracy of Battery Charge Displays Follow these guidelines to increase the accuracy of all battery charge displays: ■ Allow a battery pack to discharge to the low-battery level through normal use before charging it. ■ When you charge a battery pack, charge it fully. ■ Calibrate a new battery pack before you charge it. ■ Check the calibration on a battery pack that has not been used for 2 weeks or more before you charge it.
Using the Charge Displays on the Screen Interpreting On-Screen Charge Displays ■ Most displays that contain battery charge information identify battery pack locations by number. The battery pack location numbers in a window correspond as follows to the battery pack locations in the computer and an optional docking base.
Calibrating a Battery Pack Calibration increases the accuracy of all battery charge displays. Use the calibration utility both to check the calibration of a battery pack and to calibrate a battery pack. A battery pack cannot be calibrated unless the utility reports that it needs calibration. Although the calibration utility supports all battery packs that can be used in the computer, the utility can be run on only one battery pack at a time.
Checking the Calibration of a Battery Pack 1. Insert the battery pack into the computer battery bay or a computer or optional docking base MultiBay. NOTE: To check the calibration of a battery pack in a docking base MultiBay, the computer must be docked and the base must be connected to external power. 2. In Windows 95 select Start!Settings!Control Panel! Power icon!Battery Calibration tab. In Windows 98 select Start!Settings!Control Panel! Power Management icon!Battery Calibration tab. In Windows NT 4.
Running a Calibration 1. Insert the battery pack into the computer battery bay or MultiBay. Then connect the computer to external power through the AC Adapter, and optional docking base that is connected to external power, or an optional Automobile Power Adapter/Charger. 2. In Windows 95 select Start!Settings!Control Panel! Power icon!Battery Calibration tab. In Windows 98 select Start!Settings!Control Panel! Power Management icon!Battery Calibration tab. In Windows NT 4.
Setting Power Preferences You can increase, decrease, and allocate the power used by the computer by setting power preferences. Increasing power increases performance, while decreasing power conserves energy and extends battery operating time. By decreasing power to unused components and functions, you can allocate more power to the components and functions you are currently using. Many power preferences are timeout settings.
Setting Power Preferences in Windows 95 Preference Procedure from Control Panel Select a preset battery conservation level that applies whenever the computer is running on battery power. Select Power icon!Battery Conservation Settings tab, then select a conservation level: ■ High—Provides maximum battery conservation. ■ Medium—Balances battery conservation and system performance. ■ None (drain)—Provides maximum power.
Setting Power Preferences in Windows 95 Continued Preference Procedure from Control Panel Change location of Hibernation file. Select Power!Hibernation tab, then select the new location from the Drive for Hibernation File drop-down list box. Enable/Disable Hibernation. Select Power!Hibernation tab, then select the On or Off radio button. CAUTION: If the computer reaches a critical low-battery condition while Hibernation is turned off, unsaved work will be lost.
Setting Power Preferences in Windows 98 Preference Procedure from Control Panel Select a preset battery conservation level that applies whenever the computer is running on battery power. Select Power Management!Battery Conservation Settings tab, then select a conservation level: ■ High—Provides maximum battery conservation. ■ Medium—Balances battery conservation and system performance. ■ None (drain)—Provides maximum power.
Setting Power Preferences in Windows NT 4.0 Preference Procedure from Control Panel Select a preset battery conservation level that applies whenever the computer is running on battery power. Select Compaq Power!Battery Conservation Settings tab, then select a conservation level: ■ High—Provides maximum battery conservation. ■ Medium—Balances battery conservation and system performance. ■ None (drain)—Provides maximum power.
Setting Power Preferences in Windows NT 4.0 Continued Preference Procedure from Control Panel Enable/disable low-battery warning beeps. Select Compaq Power!Battery Conservation Settings tab, then select the On or Off radio button. Exit Suspend after a userselected timeout. Select Compaq Power!Resume Timer tab. Select the Enabled checkbox, then select a date and time from the corresponding drop-down list boxes. Set Hibernation timeout.
Setting Power Preferences in Windows 2000 Professional Preference Procedure from Control Panel Select a preset battery conservation level that applies whenever the computer is running on battery power. Select Power Options icon!Battery Conservation Settings tab, then select a conservation level: ■ High—Provides maximum battery conservation. ■ Medium—Balances battery conservation and system performance. ■ None (drain)—Provides maximum power.
Using SpeedStep Performance Modes The Intel Pentium III with SpeedStep technology can enable an automatic change in processor speed when the power source changes between AC power and battery power. Choosing a Performance Mode The SpeedStep technology offers two preset performance modes: ■ In Maximum Performance mode, the processor runs at full speed to provide maximum performance.
Setting SpeedStep Preferences NOTE: If the SpeedStep window and icon are not accessible, they may be disabled in Computer Setup. To enable the window and icon (and other settings in the SpeedStep window), refer to the table in “Using Computer Setup,” later in this section. Using the SpeedStep Window To open the SpeedStep window from the desktop— In Windows 95 or Windows NT 4.0, select Start!Programs! Intel SpeedStep technology.
Setting SpeedStep Preferences in the SpeedStep Window Continued Preference Procedure Turn off the audible alert of a performance mode change. Select the Advanced button, then: 1. Select the checkbox for Disable Audio Notification When Performance Changes. 2. Select OK in the Advanced window. 3. Select OK or Apply in the main SpeedStep window. Set the computer to change Select the Advanced button, then: automatically between Maximum 1.
Using the SpeedStep Icon The SpeedStep icon displays on the taskbar by default and changes to indicate whether the computer is running in Maximum Performance or Battery Optimized mode. The icon can also be used for the tasks described in the following table. SpeedStep Icon Tasks Task Procedure Display current performance mode. Open the SpeedStep window. Change the current performance mode. Rest the pointer over the icon. Double-click the icon.
Battery Conservation Checklists Battery Conservation Practices ■ Exit modem applications and turn off local area network (LAN) connections when you are not using them. ■ Disconnect external equipment you are not using that is not connected to an external power source. ■ If you leave your work, initiate Suspend (Standby) or Hibernation or shut down the computer. ■ Stop or remove PC Cards you are not using. ■ Use the Fn+F10 hotkeys to quickly raise and lower display brightness as you work.
chapter 5 U SING D RIVES Caring for Drives CAUTION: To prevent loss of work and damage to the computer or a drive: ■ If you are inserting or removing a hard drive, shut down the computer. Do not remove a hard drive while the computer is on or in Suspend (Standby) or Hibernation. To ensure that the computer is not in Hibernation, turn the computer on, then shut it down. ■ Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector.
Selecting Drive Locations The computer has three bays for drives. ■ The hard drive bay supports only a hard drive. The hard drive in the hard drive bay is the primary hard drive. ■ The MultiBay supports any 12.7 mm drive, such as a diskette drive, SuperDisk LS-120 drive, CD-ROM drive, DVD-ROM drive, or a second hard drive. An Armada MultiBay hard drive adapter is required to use a hard drive in the MultiBay.
Hard Drives ! WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. Removing a Hard Drive from the Hard Drive Bay 1. Save your work, then shut down the computer. 2. Push down the hard drive tab on the front of the hard drive until it snaps away from the front of the computer 1. 3. Lift up the front cover of the drive 90 degrees to create a handle 2 and pull the hard drive out of the hard drive bay.
Inserting a Hard Drive into the Hard Drive Bay 1. Save your work, then shut down the computer. 2. Slide the hard drive into the hard drive bay until it is seated and the cover is flush with the front of the computer. 5-4 Using Drives COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Karen Williams Saved date: 05/31/00 10:00 AM Part Number: 168893-001 File name: CH05.
Inserting a Hard Drive into a MultiBay Hard Drive Adapter 1. Push the two slide tabs 1 toward the outside of the adapter. 2. Lower the drive, label side up, into the adapter 2, then slide the drive connectors on the drive toward the drive connectors in the adapter 3 until the connectors engage and the drive is seated. 3. Push the two slide tabs toward the drive so that both tabs are flush with the outside of the adapter. Removing a Hard Drive from a MultiBay Hard Drive Adapter 1.
Inserting a Hard Drive Assembly into the MultiBay 1. Save your work, then shut down the computer. 2. Be sure the slide tabs on the sides of the Armada MultiBay hard drive adapter are closed flush with the sides of the adapter. 3. With the connector on the drive assembly (the hard drive inserted into the MultiBay hard drive adapter) facing the computer, slide the hard drive assembly into the MultiBay until the assembly is seated.
Removing a Hard Drive Assembly from the MultiBay 1. Save your work, then shut down the computer. 2. Close the display. 3. With the MultiBay facing you, tilt the computer up 1. 4. Slide the MultiBay release latch toward the opening of the MultiBay 2. 5. Pull the hard drive assembly (the hard drive inserted into the MultiBay hard drive adapter) out of the MultiBay by grasping the notch on the bottom of the drive 3.
CD-ROM and DVD-ROM Drives CD-ROM drives and DVD-ROM drives can be inserted and removed from the computer MultiBay without shutting down the computer. Removing a CD-ROM Drive or DVD-ROM Drive 1. Remove the compact disc from the media tray. 2. Close the tray. 3. With the MultiBay facing you, tilt the computer up 1. 4. Slide the MultiBay release latch 2 toward the opening of the MultiBay. 5. Pull the drive out of the MultiBay by grasping the notch on the bottom of the drive 3.
Inserting a CD-ROM Drive or DVD-ROM Drive With the drive connector facing in, slide the drive into the MultiBay until the connectors engage and the drive is seated. Using Drives 5-9 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Karen Williams Saved date: 05/31/00 10:00 AM Part Number: 168893-001 File name: CH05.
Inserting a Disc into a CD-ROM Drive or DVD-ROM Drive 1. Turn on the computer. 2. Press the media eject button on the front panel 1 to release the media tray. 3. Slowly pull out the tray until it is fully extended. 4. Remove the disc from its protective case and press it onto the tray spindle 2. Handle the disc by the edges, not by the flat surfaces. 5. Push lightly on the front panel of the media tray to close it.
Removing a Disc from a CD-ROM Drive or DVD-ROM Drive 1. Turn on the computer. 2. Press the eject button on the front panel 1 to open the media tray. 3. Slowly pull out the tray until it is fully extended. 4. Remove the disc from the tray 2. Handle it by the edges, not by the flat surfaces. 5. Place the disc in its protective case. 6. Push the front panel of the media tray to close it.
Diskette Drive and SuperDisk LS-120 Drive Diskette drives and SuperDisk LS-120 drives can be inserted and removed from the computer MultiBay without shutting down the computer. Removing a Diskette Drive or SuperDisk LS-120 Drive from the MultiBay 1. Remove the diskette from the drive. 2. With the MultiBay facing you, tilt the computer up 1. 3. Slide the MultiBay release latch 2 toward the opening of the MultiBay. 4. Pull the drive out of the MultiBay by grasping the notch on the bottom of the drive 3.
Inserting a Diskette Drive or SuperDisk LS-120 Drive into the MultiBay With the drive connector facing in, slide the drive into the MultiBay until the connectors engage and the drive is seated. Using Drives 5-13 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Karen Williams Saved date: 05/31/00 10:00 AM Part Number: 168893-001 File name: CH05.
Using a Diskette Drive Externally By using a diskette drive externally, the drive can be accessed while another drive or a battery pack is in the MultiBay. An external diskette drive assembly (a diskette drive inside an external diskette drive bay) is included with the computer. The external diskette drive bay supports only a diskette drive. No other type of drive, including a SuperDisk LS-120 drive, can be used in this bay.
Removing a Diskette Drive from the External Diskette Drive Bay A diskette drive must be removed from the external diskette drive bay before it can be inserted in the MultiBay. To remove the diskette drive from the drive bay— 1. Turn the diskette drive bay upside down. 2. Gently slide the drive away from the diskette drive cable connectors, then pull the drive out of the drive bay. Inserting a Diskette Drive into the External Diskette Drive Bay 1. Turn the diskette drive bay upside down. 2.
Inserting a Diskette into a Diskette Drive or SuperDisk LS-120 Drive 1. Hold the diskette by the edge covered by the label, label facing up. 2. Gently push the diskette into the drive until it clicks into place. The media eject button ejects to show that the diskette is inserted correctly. Removing a Diskette from a Diskette Drive or SuperDisk LS-120 Drive 1. Press the media eject button to eject the diskette. 2. Remove the diskette from the drive.
Changing the Startup Sequence with MultiBoot When more than one drive is in the system, the computer selects the drive to start from by searching sequenced locations for, first, a bootable CD-ROM or DVD-ROM; second, a bootable diskette; and third, a bootable hard drive. NOTE: A bootable device or medium contains files needed by the computer to start up and operate properly.
IMPORTANT: Changing the boot order also changes the logical drive designations. For example, if you start up from a hard drive in the computer MultiBay, that hard drive becomes drive C and a hard drive in the hard drive bay becomes drive D. If you start up from a diskette drive in the external diskette drive bay, that diskette drive becomes drive A. Starting up from a network board does not affect logical drive designations.
Changing the Startup Sequence in Compaq Computer Security 1. Access the Compaq Computer Security window: ■ Select Start!Settings!Control Panel. Select the Compaq Computer Security icon. or ■ Right-click the Compaq Computer Security icon in the Windows taskbar, then select Security Properties. 2. Select the Boot Security tab. 3. Select the Enable Multi-Boot checkbox. 4. Use the Move Up and Move Down buttons to display your preferences in the Boot Order list.
chapter 6 S ECURING THE C OMPUTER Security Features Quick Reference To Protect Against This Risk Use This Security Feature Unauthorized use of the computer Power-on password, with or without Quick Controls Unauthorized access to the Computer Setup (administrator) Setup and Compaq Computer password* Security utilities Unauthorized access to the contents of a hard drive DriveLock Unauthorized use of a drive or port Device disabling Unauthorized access to the processor System information serial numbe
Using Security Utilities All security features except DriveLock can be set in either the Computer Setup utility or the Compaq Computer Security utility, unless otherwise noted. The Computer Setup utility can be used even when your Windows operating system is not functioning or will not load. Some passwords and Quick Controls can also be set in some operating systems, as described in your operating system documentation.
Using a Power-on Password A power-on password ■ Prevents unauthorized use of the computer. Once set, it must be entered each time the computer is turned on or restored from Hibernation. ■ Enables you to use Quick Controls. ■ Is not case sensitive, can be the same as any other 7-character password, and can include up to 7 alphanumeric characters. It cannot include a forward slash (“/”).
Setting a Power-on Password in Compaq Computer Security 1. Access the Computer Security tab. ■ In Windows 95 or Windows 98— ❏ Select Start!Settings!Control Panel. Select the Passwords icon, then select the Computer Security tab. or ❏ ■ Right-click the Compaq Computer Security icon in the Windows taskbar, then select Password Properties. In Windows NT 4.0 or Windows 2000 Professional— ❏ Select Start!Settings!Control Panel, then select the Passwords icon.
Changing or Deleting a Power-on Password at the Power-on Password Prompt 1. Turn on (do not restart) the computer. 2. At the password prompt ■ To change a power-on password—Type the old password followed by a forward slash (“/”), the new password followed by a forward slash, then the new password followed by a forward slash.
Using Quick Controls When a power-on password is set, the following Quick Controls are available: ■ QuickLock—Disables the keyboard and pointing device. (In Compaq Computer Security this option is called Enable QuickLock of the Keyboard.) ■ QuickLock on Suspend—Sets the computer to initiate QuickLock whenever the computer enters Suspend (Standby). (In Compaq Computer Security this option is called QuickLock on Standby.
Setting Quick Controls in Computer Setup 1. Turn on or restart the computer, then press F10 when the blinking cursor appears upper-right on the screen. ■ To change the language, press F2. ■ For navigation instructions, press F1. 2. Select Security!Password Options. Enter your preferences, then press F10. NOTE: Password Options cannot be selected unless a power-on password is set. 3.
2. Press the Power-on Password Options button. NOTE: The Options button is not available unless a power-on password is set or if a USB keyboard has ever been connected to the computer. 3. Select the checkbox for each Quick Control you want to enable. NOTE: Unless Enable QuickLock of the Keyboard is selected, the QuickBlank the Screen When Locked or QuickLock on Standby checkboxes cannot be selected. 4. To apply your preferences, select the OK button.
Using a Setup (Administrator) Password This password ■ Is called a setup password in Computer Setup and an administrator password in Compaq Computer Security. ■ Protects the configuration settings and system identification information in both the Computer Setup and Compaq Computer Security utilities. Once set, this password must be entered to ■ ❏ Access Computer Setup. ❏ Access any display in Compaq Computer Security that contains system settings.
To delete a setup (administrator password)—Type the current password in the Old Password field, then press F10. 3. To save your preferences, then close Computer Setup and restart the computer, select File!Save Changes and Exit, then press Enter. 4. When prompted to confirm your action, press F10. ■ Setting a Setup (Administrator) Password in Compaq Computer Security 1. Access the Computer Security tab in the passwords window. ■ In Windows 95 or Windows 98— ❏ Select Start!Settings!Control Panel.
Using DriveLock CAUTION: If you forget both the DriveLock user password and the DriveLock master password, the protected hard drive is permanently unusable. IMPORTANT: To access the DriveLock settings in Computer Setup, you must open Computer Setup after shutting down, then turning on the computer. If you open Computer Setup from a Windows restart, DriveLock settings are not accessible. ■ ■ DriveLock prevents unauthorized access to the contents of a hard drive.
■ ■ A user or master password can be up to 32 alphanumeric characters and is not case sensitive. ❏ The user and master password can be the same. A user or master password that is 7 characters or less can be the same as any other password. ❏ When the computer is starting up from a hard drive protected with DriveLock, you will not be prompted for a power-on password if you enter a user or master password that is the same as the power-on password.
9. To confirm DriveLock protection on the drive you have selected, type DriveLock in the confirmation field, then press F10. 10. To save your DriveLock settings, then close Computer Setup and restart the computer, select File!Save Changes and Exit, then press Enter. 11. When prompted to confirm your action, press F10. Accessing a Protected Hard Drive 1. Ensure that the drive is inserted into the computer (not an optional docking base). 2.
4. Select the location of the hard drive, then press F10. ■ To change a user or master password—In the field of the password you want to change, type the current password in the Old Password field, type the new password in the New Password and Verify New Password fields, then press F10. ■ To remove DriveLock protection from the drive— Toggle the protection field to disable and press F10. Then type your master password in the Old Password field and press F10. 5.
Enabling or Disabling a Device in Compaq Computer Security 1. Access the Compaq Computer Security window: ■ Select Start!Settings!Control Panel. Select the Compaq Computer Security icon. or ■ Right-click the Compaq Computer Security icon in the Windows taskbar, then select Security Properties. 2. Select a tab: ■ To enable or disable the serial, infrared, parallel, or USB port—Select the Port Security tab. ■ To enable or disable diskette boot, access, or write— Select the Boot Security tab.
Managing System Information ■ You can use either Computer Setup or Compaq Computer Security to ❏ Display or enter the computer serial number, asset tag, and ownership tag. ❏ Display or enter a battery pack serial number and asset tag. ❏ Display or enter a docking station serial number and asset tag. ❏ Display or enter the processor serial number. ❏ Enable or disable the ability of the processor to report the processor number to software.
■ To enable/disable the reporting of the processor serial number by the processor to software—Select Advanced menu!Device Options. ■ To specify how the computer recognizes multiple, identical docking bases that are identically equipped— Select Advanced menu!Device Options. (Select Disable to recognize the docking abases as a single docking base; select Enable to recognize the docking bases individually, by serial number.) 3. To enter your information or preferences, press F10. 4.
■ To view or enter information about an optional docking base—Select the docking base in the Manageable Devices list. View or enter information in the following text boxes. ❏ The Serial Number box is Read Only. ❏ The Asset Tag box can be used to describe the docking base using no more than 16 alphanumeric characters. NOTE: A docking base will not list in the Manageable Devices list unless the computer is docked.
Displaying or Securing the Processor Serial Number in Compaq Computer Security 1. Access the Compaq Computer Security window: ■ Select Start!Settings!Control Panel. Select the Compaq Computer Security icon. or ■ Right-click the Compaq Computer Security icon in the Windows taskbar, then select Security Properties. 2. Select the Information tab. 3. Select Processor in the Manageable Devices list.
Connecting an Optional Cable Lock Loop the cable around a secure object, then insert the cable lock 1 into the security cable slot 2 and lock it with the cable lock key 3. 6-20 Securing the Computer COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by: Integrity Group Saved date: 06/01/00 10:45 AM Part Number: 168893-001 File name: CH06.
chapter 7 U SING AN I NTERNAL M ODEM The information in this chapter applies to all computer models with internal modems. NOTE: The modem does not support the modem pass-through connection available on some optional docking bases. Connecting the Modem Cable IMPORTANT: The internal modem uses a universal DAA (Direct Access Arrangement) that supports multiple countries. However, in some regions, you may need to use an adapter to connect the modem to the telephone wall jack.
To connect the modem to an RJ-11 wall jack— IMPORTANT: The modem cable, which has a 6-pin RJ-11 connector at each end, may contain noise suppression circuitry 1. This circuitry prevents interference with TV and radio reception. Orient a cable with this circuitry as shown in the following illustration. 1. Plug one end of the modem cable into the RJ-11 jack on the computer 2. 2. Plug the opposite end of the cable into an RJ-11 wall jack 3.
Setting Up the Modem The following procedures are necessary only if your modem name does not display at Start!Settings!Control Panel! Modem. In Windows 95 or Windows 98—Select Start!Settings! Control Panel!Modem. The Install New Modem setup wizard displays. To set up the modem with this wizard: 1. On the first screen, select Other, then select the Next button. 2. On the second screen, select your modem model name or select the Next button to prompt your operating system to detect the modem. 3.
Selecting Communication Software You can operate the modem with preinstalled or optional software. To use preinstalled modem software—Select Start!Programs. Then, ■ ■ For terminal emulation and data transfer ❏ In Windows 95, Windows NT 4.0, or Windows 98, select Accessories!HyperTerminal. ❏ In Windows 2000 Professional select Accessories! Communications!Hyperterminal. For fax emulation and transfer ❏ In Windows 95 select Accessories!Fax!Compose New Fax. ❏ In Windows 98, Windows NT 4.
To load a script file for Lotus Notes version 4.x or later— 1. In Windows Explorer select C:\Program Files\Compaq\ CPQLANModem\Modem\Scripts. 2. Copy the LN56kcom.mdm file in the Scripts folder to the Notes\Data\Modems folder. 3. Open the Lotus Notes application. 4. From the menu bar, select File!Tools!User Preferences!Ports icon. 5. Make sure the Port Enabled checkbox is selected. 6. Make sure the modem COM port selected is COM2. 7. Select the COMx Options button. 8.
Using Modem Commands and Dial Modifiers You can configure most communications software without the use of AT commands or dial modifiers. ■ ■ If you prefer to configure the modem using AT commands, ❏ In Windows 95, Windows NT 4.0, or Windows 98, select Accessories!HyperTerminal. ❏ In Windows 2000 Professional select Accessories! Communications!HyperTerminal. Command sets for all modem models are available at the Compaq website at http://www.compaq.
Using the Modem While Traveling Internationally Using a Country-Specific Modem Adapter Telephone jacks vary by country. The modem cable included with the computer plugs directly into an RJ-11 telephone jack. To plug the modem cable into a different type of telephone jack, you must use a country-specific modem cable adapter.
Selecting a Country-Specific Modem Configuration The internal modem is configured to meet operating approval in the country where you purchased your computer. To set the modem to comply with telecommunications standards and regulations in other countries, you must change the country selection setting. To confirm that the modem has been approved for use by the telecommunications agency in the desired country, check the modem agency approvals label on the bottom of the computer.
■ In Windows 2000 Professional—Select Start!Settings! Control Panel!Phone and Modems Options. Select the Dialing Properties tab, then 1. On the Locations list, select the location from which you are dialing. 2. Select the Edit button. 3. Select the new country from the drop-down list in the Country/region box. 4. To save the new country selection, select the Apply button.
In Windows 2000 Professional— 1. Select Start!Settings!Control Panel!Phone and Modem Options!Modem tab. 2. Select your modem, then select Properties. 3. Select the General tab, then clear the Wait for Dial Tone Before Dialing checkbox. NOTE: If you continue to receive the No Dial Tone error message after clearing the checkbox, select Start!Settings! Control Panel!Phone and Modems Options. 1. Select the Dialing Properties tab, then, in the Locations list, select the location from which you are dialing. 2.
Reinstalling or Updating Drivers (Windows 95 or Windows 98) To update or reinstall modem drivers: ■ First, uninstall the currently loaded modem drivers. ■ Second, install or restore the modem drivers. Uninstalling Modem Drivers (Windows 95 or Windows 98) 1. Select Start!Settings!Control Panel, then double-click Add/Remove Programs and select the Install/Uninstall tab. 2. Select Compaq 56K (V.90) Mini PCI from the program list. 3. Select the Add/Remove button. 4. Select Yes to confirm the removal. 5.
Reinstalling or Updating Drivers (Windows NT 4.0) IMPORTANT: To uninstall or reinstall modem or LAN drivers in Windows NT 4.0, you must log in to Windows NT with Administrator privileges. To update or reinstall modem drivers: ■ First, uninstall the currently loaded modem drivers. ■ Second, install or restore the modem drivers. Uninstalling Modem Drivers (Windows NT 4.0) 1. Select Start!Settings!Control Panel, then double-click Add/Remove Programs and select the Install/Uninstall tab. 2.
Reinstalling or Updating Drivers (Windows 2000 Professional) IMPORTANT: To uninstall or reinstall modem or LAN drivers in Windows 2000 Professional, you must log in to Windows 2000 Professional with Administrator privileges. To update or reinstall modem drivers: ■ First, uninstall the currently loaded modem drivers. ■ Second, install or restore the modem drivers. Uninstalling Modem Drivers (Windows 2000 Professional) 1. Select Start!Settings!Control Panel.
chapter 8 C ONNECTING TO A L OCAL A REA N ETWORK A network computer model can be connected to a Local Area Network (LAN). A network computer model ■ Has an internal modem/NIC (network interface card) combination card. ■ Has an RJ-45 jack on the right side. ■ Has preinstalled LAN drivers. ■ Supports network speeds up to ■ ❏ 10 Mbps when connected to a 10BaseTX network. ❏ 100 Mbps when connected to a 100BaseTX network.
Connecting to a LAN IMPORTANT: The network cable, which has an 8-pin RJ-45 connector at each end, may contain noise suppression circuitry 1. This circuitry prevents interference with TV and radio reception. Orient a cable with this circuitry as shown in the following illustration. 1. Plug the LAN cable into the RJ-45 jack on the computer 2. 2. Plug the other end of the cable into a network jack 3. 3. Restart the computer, then connect to the network.
Accessing the Network at Startup A network computer model supports both the PXE (Preboot eXecution Environment) and RPL (Remote Program Load) preboot network protocols. To connect to your PXE or RPL server during startup—Press F12 when the Network Service Boot message appears very briefly in the lower-right corner of the screen. To set the computer to connect to your PXE or RPL server at startup—Refer to “Changing the Startup Sequence with MultiBoot” in Chapter 5 of this guide.
To uninstall LAN drivers— 1. On the Install/Uninstall tab, select Intel PRO Ethernet Adapter and Software from the list of programs. 2. Select the Add/Remove button. 3. Select OK to confirm the removal. 4. Restart the computer, then begin installing the modem drivers. Reinstalling LAN and Modem Drivers (Windows 95 and Windows 98) To reinstall LAN drivers— When you restart the computer, the computer displays the New Hardware Found PCI Ethernet Controller dialog box. 1.
3. Select the Next button, then continue to select the Next button on succeeding screens until the computer copies the modem drivers. 4. To complete the installation of the modem drivers, select Finish. NOTE: It is not necessary to restart the computer after installing the modem drivers. Confirming the Network Protocol (Windows 95 or Windows 98) After reinstalling the LAN and modem drivers, it is recommended that you confirm the network protocol setting: 1. Select Start!Settings!Control Panel.
Uninstalling Modem and LAN Drivers (Windows NT 4.0) To uninstall modem drivers— 1. Select Start!Settings!Control Panel, then double-click Add/Remove Programs. 2. Select Compaq 56K (V.90) Mini PCI from the list of programs. 3. Select the Add/Remove button. 4. Select Yes to confirm the removal. 5. If you are prompted to restart the computer, select No. 6. Select OK to close the Add/Remove Programs window. To uninstall LAN drivers— 1.
To install Windows NT Networking— 1. Select Start!Settings!Control Panel, then double-click the Network icon. 2. At the Windows NT Networking installation prompt, select the Yes button. 3. Select Wired to the Network, then select the Next button. 4. Select the Select from List button. 5. Select the Have Disk button. 6. When prompted, type the path to the Intel PRO/100+ Mini PCI drivers: C:\Program Files\Compaq\CPQLANModem\Network 7. Select the OK button. 8. Select Intel PRO Adapter. 9.
Reinstalling LAN Drivers (Windows NT 4.0) 1. Select Start!Settings!Control Panel, then double-click the Network icon. 2. Select the Adapters tab. 3. Select the Add button. 4. Select the Have Disk button. 5. When prompted for the path to the Intel PRO/100+ Mini PCI drivers, type the following, then select the OK button. C:\Program Files\Compaq\CPQLANModem\Network 6. Select Intel PRO Adapter, the select the OK button. 7. Select the properties for your LAN environment, then select the OK button. 8.
Reinstalling or Updating Drivers (Windows 2000 Professional) IMPORTANT: To uninstall or reinstall modem or LAN drivers in Windows 2000 Professional, you must log in to Windows 2000 Professional with Administrator privileges. To update or reinstall modem and LAN drivers: ■ First, uninstall the currently loaded modem drivers. ■ Second, install or restore the LAN drivers. ■ Third, install or restore the modem drivers. Uninstalling Modem Drivers (Windows 2000 Professional) 1.
Installing or Restoring LAN Drivers (Windows 2000 Professional) 1. Select Start!Settings!Control Panel, then double-click the System icon. 2. Select the Hardware tab, then double-click the Device Manager button. 3. Double-click Network adapters, then double-click Intel PRO/100+ MiniPCI. 4. Select the Driver tab, then the Update Driver button. 5. When the Upgrade Device Driver Wizard appears, select the Next button. 6.
chapter 9 U PGRADING M EMORY Managing Random Access Memory (RAM) ■ To view the amount of RAM in the system, select Start! Settings!Control Panel!Compaq Diagnostics. ■ You can increase RAM with optional memory expansion boards or PC Cards. For ordering information, go to the Compaq website at http://www.compaq.com, or refer to Appendix A to contact a Compaq authorized dealer, reseller, or service provider. ■ When RAM increases, the hard drive space reserved for the hibernation file also increases.
Inserting or Removing a Memory Expansion Board ! WARNING: The memory compartment is the only user-accessible internal compartment on the computer. All other areas that require a tool to access should be opened only by a Compaq authorized service provider. ! WARNING: Failure to unplug the power cord and remove the battery pack before installing a memory expansion board can damage the equipment and expose you to the risk of electrical shock.
5. Release the four tabs located along the top of the keyboard to release the keyboard from the computer 1. 6. Carefully fold the computer keyboard away from the computer 2. Removing a Memory Expansion Board 1. Pull away the retention clips on each side of the memory expansion board 1. The board tilts upward 2. 2. Lift the edge of the memory expansion board to a 45-degree angle and gently slide it out of the memory expansion slot. 3.
Inserting a Memory Expansion Board All memory expansion boards supported by the computer ■ Can be used in either of the two memory expansion slots. ■ Are keyed (notched) to ensure correct positioning. 1. Slide the memory expansion board into an empty memory expansion slot at a 45-degree angle 1 until it is seated. 2. Push the memory expansion board down until the retention clips 2 snap into place. Replacing the Keyboard Line up the bottom edge of the keyboard and fold it back into place 1.
chapter 10 U SING A UDIO AND V IDEO F EATURES Using the Internal Microphone and the Internal Speakers ■ The microphone 1 has a standard sensitivity of -50 dB and supports audio input optimally when the display is open. ■ The two internal speakers 2 provide stereo audio playback for multimedia applications. When the computer is docked in an optional expansion base, these speakers are disabled and system sound plays through the expansion base speakers.
Connecting an External Audio Device CAUTION: To prevent possible damage to an external device, do not plug a single-sound channel (monaural) connector into the stereo speaker/headphone jack.
Connecting a Device to the Stereo Speaker/Headphone Jack ! ■ ■ WARNING: To reduce the risk of personal injury, adjust the volume before putting on headphones or a headset. Use only a 3.5-mm stereo plug. For best sound quality, ❏ Headphones should be 32 ohms. ❏ External speakers should be at least 8 ohms. Connecting an external audio device to the stereo speaker/ headphone jack disables the computer stereo speakers. Adjusting Volume You can adjust system volume from the keyboard using hotkeys.
Connecting an External Video Device ■ ■ The composite video-out jack can support— ❏ Any device, such as a television, VCR, camcorder, overhead projector, or video capture card, that accepts video-in through a standard composite video connector. ❏ Video signals only. If you are setting up a configuration that combines audio and video functions, such as playing a DVD movie to a television, connect the device audio to the stereo/speaker headphone jack.
Changing the Video Mode NOTE: Color television standard modes vary even within regions. However, NTSC is common in North America; PAL, in Europe, Africa, and the Middle East; NTSC-J, in Japan; and PAL-M, in Brazil. Other South and Central American regions may use NTSC, PAL, or PAL-M. To change the color television standard mode from NTSC (default): 1. Turn on or restart the computer, then press F10 when the blinking cursor appears upper-right on the screen. ■ To change the language, press F2.
chapter 11 U SING PC C ARDS A PC Card is a credit card–sized accessory designed to conform to the standard specifications of the Personal Computer Memory Card International Association (PCMCIA). The computer supports both 32-bit (CardBus) and 16-bit PC Cards. Installing CardWare (Windows NT 4.0) Unicore Software CardWare provided by Compaq is available on your hard drive but is not installed. If you install CardWare provided by Compaq— ■ The computer provides plug and play support for all PC Cards.
Selecting a PC Card Slot PC Cards are classified as Type I, Type II, and Type III. The three types are about the same length and width, but vary in thickness. Type III cards are the thickest, at less than one-half inch (10.5 mm). The computer has two PC Card slots. These slots are not identical. ■ Type I and Type II PC Cards are supported in the top and bottom PC Card slots singly or in any combination.
Inserting a PC Card CAUTION: To prevent damage to the connectors, use minimal pressure as you insert a PC Card into a PC Card slot NOTE: Unless the computer is running Windows NT 4.0 without CardWare provided by Compaq, it is not necessary to shut down the computer before inserting a PC Card unless you are specifically instructed to do so in the PC Card documentation. 1. Hold the PC Card with the label side up. 2.
Removing a PC Card ■ First, prepare the system for the PC Card removal: CAUTION: If the computer is on and running Windows 95, Windows 98, or Windows 2000 Professional, failure to stop a PC Card before removing it may result in loss of work or a system lockup. ❏ ❏ ■ In Windows 95, Windows 98, or Windows 2000 Professional—If the computer is on, stop the PC Card before you remove it.
chapter 12 U SING I NFRARED C OMMUNICATION Communicating with Infrared ■ If the computer is running Windows 98, Windows 2000 Professional, or a preinstalled Windows 95 operating system, the computer is IrDA-compliant (4Mbps standard) and can communicate with another infrared-equipped device that is also IrDA-compliant. ■ Infrared communication ❏ Occurs through the infrared port illustrated below. ❏ Is not supported by Windows NT 4.0 without optional software that is not available from Compaq.
Configuring the Infrared Port If you are using optional infrared software, the following information may be helpful. In Windows 95 or Windows 98— ■ The infrared port default settings are: Port, COM3; address, 3; Interrupt Request (IRQ), 3.
■ To enable or disable Infrared Monitor search: 1. Open the Infrared Monitor dialog box by selecting the Infrared icon in the taskbar!Options tab. ❏ To enable Infrared Monitor search, select the checkbox for Search For and Provide Status for Devices in Range. ❏ To disable Infrared Monitor search, clear the checkbox. 2. Select OK to save your preference and close the Options dialog box. In Windows 2000 Professional—The infrared port is enabled by default each time the computer starts up.
chapter 13 U SING I NTELLIGENT M ANAGEABILITY Intelligent Manageability comprises software tools that can help you and/or your Information Services department track, troubleshoot, protect, and maintain the system. Intelligent Manageability uses such tools as Insight Management Agents, Compaq Diagnostics, Computer Setup, and Compaq Computer Security to facilitate the following: ■ Asset Management—Provides detailed configuration and diagnostic information.
Using Fault Management Alerts Identifying a Fault Management Alert The computer is preset to monitor certain hardware components. If problems are found, the following alerts may display. ■ Hard drive alert—Warns up to 72 hours in advance of impending hard drive problems; can be set to initiate a software backup. ■ System temperature alert—Prevents critical overheating.
chapter 14 C OMPUTER S ETUP AND D IAGNOSTICS U TILITIES Selecting Computer Setup or Compaq Diagnostics The computer features two Compaq system management utilities: ■ Computer Setup is a system information and customization utility that can be used even when your operating system is not working or will not load. This utility includes settings that are not available in Windows. ■ Compaq Diagnostics is a system information and diagnostic utility that is used within your Windows operating system.
Using Computer Setup Information and settings in Computer Setup are accessed from the File, Security, or Advanced menus: 1. Turn on or restart the computer. When the blinking cursor appears upper-right on the screen, press F10. ■ To change the language, press F2. ■ To view navigation information, press F1. ■ To return to the Computer Setup menu, press Esc. 2. Select the File, Security, or Advanced menu. 3.
Selecting from the Security Menu NOTE: For more information about the security features available on the Security menu, refer to Chapter 6 in this guide. Selecting from the Security Menu Select To Do This Setup password Enter, change, or delete a setup password. (The setup password is called an administrator password in Compaq Computer Security.) Power-on password Enter, change, or delete a power-on password. DriveLock passwords Enable/disable DriveLock; change a DriveLock User or Master password.
Selecting from the Advanced Menu Selecting from the Advanced Menu Select To Do This Language (or press F2) Change the Computer Setup language. Boot Options Enable/disable ■ QuickBoot, which starts the computer more quickly by eliminating some startup tests. (If you suspect a memory failure and want to test memory automatically during startup, disable QuickBoot.) ■ MultiBoot, which sets a startup sequence that can include most bootable devices and media in the system.
Selecting from the Advanced Menu Continued Select Device Options (continued) To Do This ■ Set video-out mode to NTSC (default), PAL, NTSC-J, or PAL-M.* ■ Enable/disable all settings in the SpeedStep window. (When Disable is selected, the computer runs in Battery Optimized mode.) ■ Specify how the computer recognizes multiple, identical docking bases that are identically equipped.
Using Compaq Diagnostics When you access Compaq Diagnostics, a scan of all system components appears on the screen before the Compaq Diagnostics window opens. You can display more or less information from anywhere within Compaq Diagnostics by selecting Level on the menu bar. Compaq Diagnostics is designed to test Compaq components. If non-Compaq components are tested, the results may be inconclusive. Obtaining, Saving, or Printing Configuration Information 1.
4. Select a test type: ■ Quick Test runs a quick, general test on each device in a selected category. ■ Complete Test performs maximum testing on each device in a selected category. ■ Custom Test performs maximum testing on a selected device. ❏ To run all tests for your selected device, select the Check All button. ❏ To run only the tests you select, select the Uncheck All button, then select the checkbox for each test you want to run. 5.
chapter 15 M AINTENANCE , T RAVEL , AND S HIPPING Updating Your System IMPORTANT: Compaq recommends that you install all software updates as they become available. However, if your system is connected to a network, you may need to confer with your Information Services department before updating system ROM. Obtaining Update Information and Software Checking the Compaq Website You can obtain the latest available update information and update software directly from the Compaq website at http://www.compaq.
Subscribing to the Compaq Support Software CD You can subscribe to the Compaq Support Software CD that contains detailed software support information and the software and installation instructions for the latest device drivers, system ROMs, and utilities. To obtain ordering information—Contact your Compaq authorized dealer, reseller, or service provider or go to the Compaq website at http://www.compaq.com.
Installing Software Updates Installing a Downloaded SoftPaq 1. Open and read the Readme.txt file included with the download. 2. Follow the installation instructions in the Readme.txt file or on the Compaq website. Installing a System ROM The easiest way to install a system ROM is from a diskette. NOTE: A system ROM cannot be installed directly from any other drive medium, including a SuperDisk LS-120 disk.
Restoring Software If it ever becomes necessary, you can restore any or all of the software for the operating system and language you selected during initial setup. The software and instructions for restoring it are in the QuickRestore package included with the computer. NOTE: If you are restoring a Windows NT 4.0 operating system, refer to “Installing CardWare (Windows NT 4.0)” in Chapter 11 for information about reinstalling CardWare.
Monitoring Computer Temperature When the computer is run at high power levels or for an extended period of time, it is normal for the computer to feel warm to hot. The computer complies with international safety standards for temperatures of user-accessible surfaces. For more information about operating temperatures, refer to Appendix D in this guide.
Caring for the Computer ! WARNING: To reduce the risk of electric shock or damage to internal components, do not allow liquids to drip into the computer keyboard. CAUTION: To prevent possible damage to the display, do not place anything on top of the computer when it is closed. CAUTION: Soap or other cleaning products can damage the screen and discolor the plastic. ■ ■ ■ ■ ■ Keep the computer away from excessive moisture and temperature extremes. Do not expose the computer to liquids or precipitation.
Traveling with the Computer Checklist ■ Take along a backup of your work. Do not pack the backup with the computer. ■ Hand carry the computer. Do not check it with your luggage. ■ Do not expose the computer or diskettes to a magnetic security detector. ❏ The security device that examines carry-ons placed on a conveyer belt uses x-rays and is safe for the computer and diskettes. ❏ The walk-through security device and the handheld security wands are magnetic and may damage the computer or diskettes.
chapter 16 T ROUBLESHOOTING Problems that occur while using the computer may originate with the computer, the operating system, a software application, or an optional docking base or external device: ■ For problems that may not originate with the computer, refer to your operating system, docking base, software application, or external device documentation. ■ For problems that may originate with the computer or system software, refer in this chapter ■ ❏ First, to the “Quick Solutions Checklist.
Quick Solutions Checklist NOTE: To reset a locked system, press and hold the suspend button while sliding the power switch.
Solving Audio Problems Problem Possible Cause Internal speaker Volume may be turned does not produce off or set too low. sound when an external audio source is connected to the stereo line-in jack. Line input may not be connected properly. Headphones or speakers are connected to the stereo speaker/ headphone jack, which disables the internal speakers. Volume may be muted. Solution ■ Adjust the overall volume by pressing the Fn+F5 hotkeys.
Solving Audio Problems Continued Problem Possible Cause No sound from headphones. Volume or mixing controls set incorrectly. Solution ■ Adjust the overall volume with the Fn+F5 hotkeys. ■ Use the mixing features available by double-clicking the speaker icon on the Windows taskbar. ■ Make sure the mute box is not checked. Volume too low or too loud. Sound source not selected. Verify that the sound source is selected in Control Panel! Multimedia. The headphones are connected to the wrong jack.
Solving Battery Problems Problem Possible Cause Computer is beeping and battery light is blinking. Battery pack charge is low. Solution ■ Charge the battery pack by connecting to an external power source. ■ Replace the battery pack with another fully charged battery. ■ Initiate Hibernation or turn the computer off until external power or a fully charged battery is available. Computer Volume turned down battery light too low. blinks to indicate low battery condition, but computer does not beep.
Solving Battery Problems Continued Problem Possible Cause Solution Battery charge does not last very long. Battery is exposed to higher temperatures. Put the computer in a cooler place and recharge the battery pack. Battery is exposed to extremely cold temperatures. Put the computer in a warmer place and recharge the battery pack. NOTE: The recommended operating temperature range for the battery is from 10°C to 40°C (50°F to 104°F).
Solving CD-ROM drive/DVD-ROM Drive Problems Problem Possible Cause Solution Drive cannot read a disc. Disc is not properly seated in the drive. Open the loading tray, insert the disc, then close the tray. Disc is loaded in the Open the loading tray, loading tray upside down. turn over the disc (label facing up), then close the tray. CD-ROM drive or DVD-ROM drive is not detected by the computer. Disc has a scratch on its surface. Insert a different disc. Drive is not connected properly.
Solving Diskette Drive/SuperDisk LS-120 Drive Problems Problem Possible Cause Solution Drive cannot write to a diskette. Diskette is not formatted. Format the diskette. Diskette is writeprotected. Use another diskette that is not write-protected or disable the write-protect feature. Writing to the wrong drive. Check the drive letter in your path statement. Not enough space is left on the diskette. Save the information to another diskette. Drive is disabled.
Solving Hard Drive Problems Problem Possible Cause Solution Accessing information on the hard drive is much slower than usual. Hard drive entered low power state due to timeout and is now exiting from it. Wait for the system to restore the previously saved data to its state prior to initiating a low power state. Hard drive is Run ScanDisk and Disk fragmented/not optimized Defragmenter. or has errors Hard drive does not work. Hard drive is not seated properly.
Solving Infrared Problems Problem Possible Cause Solution Cannot communicate with another computer. The appropriate software is not running on both computers. Install the appropriate software on the second device, start the second device, and start the program on both computers. The other computer does not have an IrDAcompliant infrared port. Your Compaq computer uses the IrDA communications protocol. Communication between infrared devices must use the same communications protocol.
Solving Infrared Problems Continued Problem Possible Cause Solution Cannot transmit data. Direct sunlight, fluorescent light, or flashing incandescent light is close to the infrared connections. Remove the interfering light source(s). There is interference from other wireless devices. Keep remote control units such as wireless headphones and other audio devices away from the infrared connections. There is a physical Do not place objects that will obstruction in the way.
Solving Keyboard/Numeric Keypad Problems Problem Possible Cause Solution Screen is blank and keyboard is working. A screen timeout has been initiated. Press any key to refresh the screen. QuickLock/QuickBlank has been initiated. To enable the keyboard and return your information to the screen, enter your power-on password. LCD has been disabled. Press Fn+F4 to cycle from external monitor to internal LCD. Num Lock function is not turned on.
Solving Modem Problems Continued Problem Possible Cause Modem not responding. Modem is not set up correctly in system BIOS. Modem does not dial correctly. Solution Check the computer BIOS setup. If it requires specific settings for modems, be sure that they have been enabled. ■ Make sure the Telephone number is not telephone number entered correctly in the you dialed is correct if modem’s dialing software. you are using the dialing directory or the terminal mode.
Solving Modem Problems Continued Problem Possible Cause Solution No dial tone. Phone service is not connected to the telephone wall jack. Verify that service from the local phone company by following these steps: 1. Unplug the telephone cable from the telephone wall jack. 2. Connect a telephone to the jack, pick up the handset, and listen for a dial tone. If there is a dial tone, reconnect the modem to the telephone wall jack with the telephone cable and make sure all connections are secure. 3.
Solving Modem Problems Continued Problem Possible Cause Solution Modem does not connect at highest speed. Line conditions in your area or in the area you are calling may not support the highest connect speeds. Have your telephone line checked by your local telephone service provider. Try dialing an alternate telephone number for the service you are using. Another device on your Hang up an extension telephone line may be telephone and disconnect causing interference.
Solving PC Card Problems Problem Possible Causes Solution Computer does not beep when a PC Card is inserted. PC Card is not inserted properly. Try reinserting the card. Ensure that the PC Card is inserted in the correct orientation. Insert the card gently to prevent damage to the pins. Speakers are turned off Adjust the overall system or volume is turned down. volume control using the Fn+F5 hotkeys. Make sure the mute box is not checked PC Card or card driver is not PCMCIA compliant.
Solving PC Card Problems Continued Problem Possible Cause Solution Storage PC Card does not work. SRAM and flash memory PC Cards require the memory card driver to be loaded. Memory cards can only be accessed using DOS real mode drivers. You are trying to access the storage PC Card using the wrong drive letter. Verify or change the drive letter assignment. The PC Card is not formatted. For memory cards, run MCFORMAT in MS-DOS Mode to format the PC Card.
Solving Power Problems Problem Possible Cause Computer will not turn on. Battery is discharged and computer is not connected to a power source. Solution ■ Charge the battery pack. ■ Replace the battery pack. ■ Connect the computer to an external power source. Computer turned off while it was left unattended. Battery is discharged and cables to the external power source are unplugged. Ensure that cables connecting the computer and the external power source are plugged in properly.
Solving Screen Problems Problem Possible Cause Solution Characters on computer display are dim. Computer is in direct light. Move the computer or adjust the screen. The brightness control is not set properly. Adjust the brightness control by pressing the Fn+F10 hotkeys. Press any key to refresh the screen. You may have a screen saver or screen blanking utility installed. Screen timeout was initiated. System initiated Suspend after a user-defined timeout expired.
Solving USB Problems Problem Possible Cause Solution External device connected to a USB connector does not work. The operating system limits external devices connected by USB to two tiers which can include no more than two hubs on the first tier and no more than one keyboard and one pointing device on the first or second tier. Reduce the number of connected external USB devices to no more than two hubs on the first tier, and no more than one keyboard and one pointing device on the first or second tier.
appendix A C OMPAQ C USTOMER S UPPORT Using the Compaq Support Forum Personal technical support is available from the Compaq Support Forum at the Compaq Web site. You can either browse the postings as a guest, or register as a user and submit your own questions. Compaq responds to questions within one business day. To access the Compaq Support Forum—Go to the Compaq Web site at http://www.compaq.com then select Compaq Support Forum.
■ System ROM version number and Computer Setup version number. To view these version numbers, 1. Turn on or restart the computer. 2. When the blinking cursor appears upper-right on the screen, press F10. 3. Select FileÆSystem Information. ■ Configuration and diagnostics information. To obtain, print, or save configuration and diagnostic information, refer to “Using Compaq Diagnostics” in Chapter 14 of this guide. Worldwide Telephone Numbers To use the following table—Locate your country.
Worldwide Telephone Numbers Continued Location Country Code Telephone Number $XVWULD *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW %XVLQHVV 3URGXFWV 7HFKQLFDO 6XSSRUW %HOJLXP *HQHUDO ,QIRUPDWLRQ &RPSDT &DUH &HQWHU *HQHUDO )D[ 2UGHULQJ %DFNXS 6RIWZDUH 2UGHULQJ %DFNXS 6RIWZDUH )D[ %ROLYLD 7HFKQLFDO 6XSSRUW %UD]LO *HQHUDO ,QIRUPDWLRQ &RPSDT &XVWR
Worldwide Telephone Numbers Continued Location &KLQD *HQHUDO ,QIRUPDWLRQ &XVWRPHU 5HVSRQVH &HQWHU &5& 7HFKQLFDO 6XSSRUW Country Code Telephone Number ( PDLO IRU &RPSDT $6( 7UDLQLQJ %%6 &RPSDT 9HULILFDWLRQ &HQWHU &RPSDT 0DQDJHPHQW 6HUYLFH &HQWHU &RORPELD *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW &KLQD 7UDLQLQJ#FRPSDT FRP &]HFK 5HSXEOLF *HQHUDO ,QIRUPDWLRQ
Worldwide Telephone Numbers Continued Location Country Code Telephone Number )UDQFH *HQHUDO ,QIRUPDWLRQ )77& PQ 7HFKQLFDO 6XSSRUW )77& PQ 4XLFN/LQH %%6 57& 6WDQGDUG 4XLFN/LQH %%6 51,6 *HUPDQ\ *HQHUDO ,QIRUPDWLRQ '0 PLQ *HQHUDO ,QIRUPDWLRQ )D[ '0 PLQ $OO 3URGXFWV )D[ '0 PLQ 'HVNWRS +RWOLQH '0 PLQ *UHHFH *HQHUDO
Worldwide Telephone Numbers Continued Location Country Code Telephone Number ,QGLD *HQHUDO ,QIRUPDWLRQ (PDLO ,UHODQG *HQHUDO ,QIRUPDWLRQ ,VUDHO *HQHUDO ,QIRUPDWLRQ )D[ 7HFKQLFDO 6XSSRUW ,WDO\ *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW &RPPHUFLDO PRQLWRU SURGXFWV %%6 2UGHULQJ %DFNXS 6RIWZDUH )D[ 7HFKQLFDO 6XSSRUW -DSDQ *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW 'LDO 4 7HFKQLFDO 6XSSRUW 2UGHULQJ %DFNXS 6RIWZDUH ,QIR KX#FRPSDT FRP
Worldwide Telephone Numbers Continued Location Country Code Telephone Number /X[HPERXUJ *HQHUDO ,QIRUPDWLRQ )OX[ PLQ &RPSDT &DUH &HQWHU &RPSDT &DUH &HQWHU )D[ *HQHUDO )D[ 2UGHULQJ %DFNXS 6RIWZDUH 2UGHULQJ %DFNXS 6RIWZDUH )D[ 0DOD\VLD *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW 0H[LFR *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW 3DT)D[ 1HWKHUODQGV *HQHUDO ,QIRUPDWLRQ &XVWRPHU 6XSSRUW &RPSDT &XVWRPHU 6HUYLFH
Worldwide Telephone Numbers Continued Location 3HUX *HQHUDO ,QIRUPDWLRQ 3RODQG *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW 3RUWXJDO *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW )D[ Country Code Telephone Number 5XVVLD *HQHUDO ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW 6LQJDSRUH &RPSDT &DOO &HQWHU *HQHUDO ,QIRUPDWLRQ &XVWRPHU 6XSSRUW &HQWHU )D[ 6RXWK $IULFD *HQHUDO ,QIRUPDWLRQ
Worldwide Telephone Numbers Continued Location 6ZHGHQ *HQHUDO ,QIRUPDWLRQ 6DOHV ,QIRUPDWLRQ 7HFKQLFDO 6XSSRUW FKDUJHG FDOOV )DT3D[ 4XLFN/LQH %%6 6ZLW]HUODQG ,QIR/LQH (TXLSPHQW +RWOLQH 0RQLWRUV 'HVNWRS DQG 1RWHERRNV 4XLFN/LQH %XOOHWLQ %RDUG 2UGHULQJ %DFNXS 6RIWZDUH Country Code Telephone Number 6(.
Worldwide Telephone Numbers Continued Location Country Code Telephone Number 8QLWHG .LQJGRP *HQHUDO ,QIRUPDWLRQ *HQHUDO ,QIRUPDWLRQ )D[3DT 4XLFN/LQH %%6 8QLWHG 6WDWHV 7HFKQLFDO 6XSSRUW 2.
appendix B R EGULATORY N OTICES Throughout these regulatory notices, Compaq products are referred to by their regulatory agency series numbers. Regulatory Agency Series Numbers Regulatory agencies worldwide use agency series numbers for product identification. Each approved product displays the assigned agency series number.
Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For questions regarding this declaration, write Compaq Computer Corporation P. O. Box 692000, Mail Stop 510101 Houston TX 77269-2000 or call 281-514-3333 To identify your product, refer to the part, series, or model number found on the product. If you have questions about your product that are not related to this declaration, please write Compaq Computer Corporation P. O.
Airline Travel Notice Use of electronic equipment aboard commercial aircraft is at the discretion of the airline. Power Cords If you were not provided with a power cord for your computer or for an external power accessory intended for use with your computer, you should purchase a power cord that is approved for use in your country. The power cord must be rated for the product and for the voltage and current marked on the product’s electrical ratings label.
In North America, dispose of nickel metal hydride or lithium ion batteries by taking advantage of the Compaq battery recycling program. You will be provided with a postage-paid battery pack mailer preaddressed to a reclamation facility where the metals are recycled. For more information, call the telephone number listed for your location in Appendix A. In Europe, do not dispose of batteries with general household waste.
Laser Safety All Compaq systems equipped with laser products comply with appropriate safety standards, including IEC 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies for Class 1 laser products. It does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance. CDRH Regulations The Center for Devices and Radiological Health (CDRH) of the U.S.
Only authorized technicians trained by Compaq should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard.
Selecting a country other than the one in which you are currently located may cause your modem to be configured in a way that violates the telecommunication regulations/laws of that country. In addition, your modem may not function properly if the correct country selection is not made. If when selecting a country a message appears that states that the country is not supported, this means that the modem has not been approved for use in this country and thus should not be used. U.S.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, contact your local telephone company for information on obtaining service or repairs.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local Telecommunications Company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord).
European Union Notice Telecommunications Terminal Equipment with the CE marking comply with Telecommunication Terminal Equipment and Satellite Earth Station Equipment (TTE & SES) Directive (98/13/EC), the EMC Directive (89/336/EEC), and the Low Voltage Directive (73/23/EEC) issued by the European Community.
New Zealand Modem Statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (S0 set between 2 and 10). This ensures: a. A person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. b. Caller identification (which occurs between the first and second ring cadences) is not destroyed. This equipment does not fully meet Telecom’s impedance requirements.
appendix C E LECTROSTATIC D ISCHARGE A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components. Before handling electrostatic-sensitive components, discharge static electricity by one of the methods described in this appendix. Preventing Electrostatic Discharge When Handling Drives ■ ■ Before handling a drive, discharge static electricity by touching the unpainted metal surface or lug nuts on the connectors on the back of the computer.
Grounding Methods If installation instructions direct you to unplug the computer or an optional docking base, unplug it after being properly grounded and before removing the cover. Use one or more of the following grounding methods. ■ Touch the unpainted metal surface or lug nuts on the connectors on the back of the computer or docking base. Avoid touching connector pins. ■ Touch an exterior unpainted metal surface of equipment that is connected to an electrical outlet by a grounding plug.
appendix D S PECIFICATIONS Computer Dimensions Dimension U.S. Metric +HLJKW LQ FP :LGWK LQ FP 'HSWK LQ FP U.S.
Rated Input Power Input Power Rating 2SHUDWLQJ YROWDJH ± ± 9$& 506 2SHUDWLQJ FXUUHQW $ 506 2SHUDWLQJ IUHTXHQF\ UDQJH ± +] $& :KHQ SRZHUHG E\ D '& VRXUFH 9 0$; NOTE: 7KLV SURGXFW LV GHVLJQHG IRU ,7 SRZHU V\VWHPV LQ 1RUZD\ ZLWK SKDVH WR SKDVH YROWDJH QRW H[FHHGLQJ 9UPV Port and COM Port Settings Port Port Address IRQ 6HULDO SRUW ) K ))K 86% FRQQHFWRU )K 3DUDOOHO SRUW ))K 6HULDO , 2 FRQQHFWRU &20 ) K ))K ,QIUDUHG SR
Modem Specifications Temperatures 2SHUDWLQJ WR ) WR & 6WRUDJH ± WR ) ± WR & Relative Humidity (noncondensing) 2SHUDWLQJ ± WR ± WR 6WRUDJH ± WR # ) ± WR # & Interfaces &RPPXQLFDWLRQV FRQQHFWRU 6WDQGDUG 5- WHOHSKRQH FRQQHFWRU 7HOHSKRQH FHQWUDO RIILFH QHWZRUN ,QWHUQDO '$$ Power Requirements YROWV ± YDX[ ± YROWV ± Specifications D-3 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: Karen Williams Saved by
INDEX A AC Adapter connecting, 1-6, 1-9 described, 1-9 illustrated, 1-8 when to use, 4-1 AC power connector, 1-6 AC power conservation level (Windows NT 4.0), 4-17 acoustic vent, 1-4 adapter board, for connecting computer to network. See peripheral interconnect (PCI) network adapter board for connecting computer to AC power supply. See AC Adapter for connecting computer to aircraft power supply. See Aircraft Power Adapter (optional) for connecting computer to vehicle cigarette lighter receptacle.
location number, in Compaq Computer Security, 6-18 position of, in charge or discharge sequence, 3-1 release latch, 3-3 removing battery pack from, 3-3 battery conservation level in Windows 2000 Professional, 4-19, 4-24 in Windows 95, 2-5, 4-14, 4-24 in Windows 98, 4-16, 4-24 in Windows NT 4.0, 2-5, 4-17, 4-24 battery light, 16-5.
card and socket services and enablers, for PC Card, 11-1 CardWare (Windows NT 4.0), 11-1 CD-ROM Compaq Portable Product Reference Library CD-ROM, 7-6 Compaq Support Software CD, 15-2 inserting, 5-10 removing, 5-11 CD-ROM drive.
D DAA (Direct Access Arrangement), 7-1, D-3 default settings, restoring, 14-2, 15-4 device drivers installing PC Card, 11-2 reinstalling, updating, modem and LAN (Windows 2000 Professional), 8-9 reinstalling, updating, modem and LAN (Windows 95, Windows 98), 8-3 reinstalling, updating, modem and LAN (Windows NT 4.
Email button, 2-9 embedded numeric keypad, 2-13 enablers, PC Card, 11-1 EPP (Enhanced Parallel Port) parallel port mode, 14-4 Ethernet network jack.
enabling/disabling, in Windows 98, 4-16 enabling/disabling, in Windows NT 4.0, 4-18 indicators, 4-3 initiated during critical low-battery condition, 4-5 initiating, 4-2 inserting weight saver during, 5-2 restoring from, 4-2, 4-6 system-initiated, disabled by auto insert notification, 4-19 hibernation file changing location of, in Windows 95, 4-15 changing location of, in Windows 98, 4-16 changing location of, in Windows NT 4.
K key. See also button(s); switch Fn, 2-4 Microsoft logo, 1-3 Windows application, 1-3 Key number, Product, 1-7 keyboard.
memory expansion board fault management alert, 13-2 managing increased RAM when upgrading, 9-1 protecting from electrostatic discharge, C-1 replacing, 9-2 memory, random access (RAM) displaying information about, 9-1, 14-2 fault management alert, 13-2 increasing, 9-1 information in, saved to hard drive during Hibernation, 4-2, 9-1 information saved in, during Suspend, 4-2 testing at startup, 14-4 microphone external, 10-2 internal, 10-1 internal, disabled by external, 10-2 internal, keeping acoustic vent cl
release latch, 5-7 removing battery pack from, 3-5 removing CD-ROM or DVD-ROM drive from, 5-8 removing diskette or SuperDisk LS120 drive from, 5-12 removing hard drive assembly from, 5-7 using weight saver in, 5-2 MultiBay battery pack, defined, 3-1. See also battery pack(s) MultiBay drive light, 1-2, 5-2 MultiBoot, 5-17 MultiMonitor (Windows 98), 2-6 MyArmada button, 2-9 N navigation in Computer Setup, 14-2 using pointing device, 2-2 network.
selecting, source, 4-1 setting, preferences, 4-13, 4-20 specifications, D-2 power connector, 1-6 power cord, 1-9, 15-7 power switch exiting Suspend (Standby) with, 4-3 resetting system with, 16-2 restoring from Hibernation with, 4-3 turning on computer with, 4-3 power/suspend light, 1-5, 4-3, 4-5 power-on password, 6-1, 6-3 primary battery pack, defined, 3-1. See also battery pack(s) primary hard drive, defined, 5-2.
Scroll Lock key, 2-5 scroll lock light, 1-2 Search button, 2-9 security passwords, 16-1 Quick Controls, 2-5 security cable lock, slot, 6-1, 6-20 security features cable lock (optional), 6-1, 6-20 described, on Quick Reference table, 6-1 disabling of drive, port, external device, 6-1, 6-14 DriveLock, 6-1, 6-11 Intelligent Manageability, 13-1 power-on password, 6-1, 6-3 Quick Controls, 6-1, 6-6 securing of processor serial number, 6-16, 6-19 setup (administrator) password, 6-1, 6-9 serial connector disabling/
specifications, D-1 SpeedStep. See Intel SpeedStep technology standard components included with computer, 1-8 Standby (Windows 98, Windows 2000 Professional), 4-3. See also Suspend (Standby) startup order, changing, 5-17 static electricity, C-1 Status registers, 7-6 stereo speaker/headphone jack, 10-2, 10-3 sunlight, affecting computer, 15-6 SuperDisk LS-120 drive, 15-2.
traveling with the computer Aircraft Power Adapter (optional), 1-6, 4-1 Automobile Power Adapter/Charger (optional), 1-6, 4-1 computer dimensions, D-1 operating environment specifications, D-1 shipping a drive, 5-1 shipping and travel guidelines, 15-6 using modem internationally, 7-7 troubleshooting audio problems, 16-3 battery problems, 16-5 compact disc/CD-ROM drive problems, 16-7 display problems, 16-19 hard drive problems, 16-9 infrared problems, 16-10 keyboard/numeric keypad problems, 16-12 modem probl
