Compaq Armada M700 Series of Personal Computers Maintenance and Service Guide
Notice 2001 Compaq Computer Corporation. COMPAQ, the Compaq logo, and ARMADA Registered in U. S. Patent and Trademark Office Microsoft, Windows, and Windows NT, are registered trademarks of Microsoft Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Imation and SuperDisk are trademarks of Imation Enterprises Corporation. All other product names mentioned herein may be trademarks or registered trademarks of their respective companies.
C ONTENTS preface USING THIS GUIDE Symbols ............................................................................................................................................ ix Technical Notes ................................................................................................................................ ix Serial Number....................................................................................................................................
chapter 2 TROUBLESHOOTING 2.1 Preliminary Steps.........................................................................................................................2-2 2.2 Clearing Passwords......................................................................................................................2-3 2.3 Power-On Self-Test (POST)........................................................................................................2-3 2.4 POST Error Messages ..................................
5.6 Battery Packs ...............................................................................................................................5-6 Removing a Primary Battery Pack from the Battery Bay ..............................................................5-6 Inserting a Primary Battery Pack in the Battery Bay .....................................................................5-7 5.7 Hard Drives........................................................................................................
appendix A CONNECTOR PIN ASSIGNMENTS.................................................................................................................... A-1 appendix B POWER CORD SET REQUIREMENTS 3-Conductor Power Cord Set......................................................................................................... B-1 Country-Specific Requirements .................................................................................................... B-2 Index .....................................
preface U SING T HIS G UIDE This Maintenance and Service Guide is a troubleshooting reference that can be used when servicing the Compaq Armada M700 Series of Personal Computers. Compaq Computer Corporation reserves the right to make changes to the Compaq Armada M700 Series of Personal Computers without notice. Symbols WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life.
Serial Number When requesting information or ordering spare parts, provide the computer serial number. The serial number is on the bottom of the computer.
chapter 1 P RODUCT D ESCRIPTION 1.1 Computer Features and Models The Compaq Armada M700 Series of Personal Computers offers advanced modularity, Intel Pentium III and II processors, and extensive multimedia support. Figure 1-1.
Models The Armada M700 models are shown in Table 1-1. The computer model designation is composed of a group of characters that define each model’s features.
Table 1-2 Models and Model Naming Convention Compaq Armada M700 Series of Personal Computers 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 1 2 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 3 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 4 5-6 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 7-9 1 1 1 1 1 1 1 1 1 1
Table 1-2 continued 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 1 2 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 3 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 4 5-6 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 P3 7-9 650 650 650 650 650 650 650 650 650 650 650 650 500 500 500 500 500 500 500 500 500 500 500 450 450 450 450 45
Table 1-2 continued 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 1 2 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 3 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 4 5-6 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 7-9 400 400 400 400 400 400 400 400 400 400 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 366 4X DVD-ROM drive 10 T T T T T T T T T T T T T T T T
Features The computer has the following standard features: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Intel Pentium III 1-GHz, 900-, 850-, 750-, 700-, 650-, 600- or 450-MHz processors, or Intel Pentium II 400- or 366-MHz processors, depending on computer model 8-MB SDRAM (synchronous graphics) 64-MB of SDRAM (synchronous); expandable to 288 MB 13.3- or 14.
■ Configuration Management—optimizes the computer by providing the latest drivers, utilities, and software, which are available on CD-ROM and the Compaq Web site at: www.compaq.com/support/portables NOTE: For further help with Intelligent Manageability, select Start ! Compaq Information Center ! Intelligent Manageability Accessing the Web Agent The computer may have a preinstalled Web Agent that allows computer configuration information to be viewed using Web technology.
Fault Management Fault Management features minimize downtime and data loss by monitoring system performance and generating the following alerts: " Hard drive alert—provides 72-hour advance warning of impending hard drive problems and can automatically start optional backup software. Alerts can be enabled, disabled, and tested, and software can be set to back up information whenever a hard drive alert occurs. " System temperature alert—reports overheating.
Configuration Management Configuration Management optimizes software upgrade and customer support procedures. Compaq provides support software to optimize the performance of the computer. This support software is accessible through a monthly CD-ROM subscription. Support software can also be downloaded from the Compaq Web site at: www.compaq.
1.2 Computer Components System Memory Options The main memory subsystem supports a minimum standard 32 or 64 megabytes of Synchronous SDRAM, and is expandable to 544 or 576 megabytes, depending on computer model. The minimum standard Synchronous SDRAM is installed on the system board. The upgrade SDRAM is accomplished with memory expansion boards that are available in 32-, 64-, 128-, and 256-megabytes.
Power Equipment The following power options are available: " " " " AC Adapter Lithium ion battery pack Automobile Power Adapter/Charger Aircraft Power Adapter AC Adapter The AC Adapter is field replaceable and ships with the computer and is available as an option. The 50-watt AC Adapter converts 100/220 volts AC into low-voltage DC to drive the DC-DC converter and to recharge the battery pack. The output of this AC/DC supply is the battery voltage, approximately 10 to 19 volts.
1.3 Computer External Components The computer external components on the front, rear, left side, right side, top, and bottom, of the computer as well as the keyboard components for the pointing stick model and TouchPad model are shown in the following figures and described in the accompanying tables. Front Components Figure 1-2 Front Components Table 1-5 Front Components Item Components Function 1 Hard drive bay Accepts removable hard drive.
Rear Components Figure 1-3 Rear Components Table 1-6 Rear Components Item Component Function 1 Infrared port 2 Serial connector 3 External monitor connector Docking connector Provides wireless communication between the computer and another infrared-equipped device using an infrared beam. Connects an optional external serial device such as a mouse. Connects optional external display. 4 5 6 7 8 Connects the computer to the optional desktop expansion base or convenience base.
Left Side Components Figure 1-4 Left Side Components Table 1-7 Left Side Components Item Component Function 1 Composite TV connector Connects a television, VCR, camcorder, or overhead projector. 2 Cable lock connector Accepts an optional security cable to secure the computer to a fixed object to prevent theft. 3 Airflow vent Allows airflow needed to cool computer components. Do not block airflow vents.
Right Side Components Figure 1-5 Right Side Components Table 1-8 Right Side Components Item Component Function 1 PC Card slots Accepts 16- and 32-bit CardBus PC Cards. 2 Airflow vent Allows airflow needed to cool computer components. Do not block airflow vents. 3 MultiBay Supports MultiBay devices. 4 Audio bass port Enhances stereo sound. 5 RJ-11 jack Connects a standard telephone cable or modem cable to the computer. 6 RJ-45 jack Connects a network cable to the computer.
Top Components Figure 1-6 Top Components 1-16 Product Description
Table 1-9 Top Components Item Component/Icon Function 1 Display switch Turns off the display if the computer is closed while turned on. 2 Suspend button* Initiates and exits Suspend.** When pressed with the Fn key, initiates Hibernation. 3 Hard drive light Indicates hard drive activity. 4 MultiBay drive light Indicates MultiBay activity. 5 Num Lock light Indicates that Num lock is on and the embedded numeric keypad is enabled. 6 Caps Lock light Indicates that Caps lock is on.
Bottom Components Figure 1-7 Bottom Components Table 1-10 Bottom Components Item Component Function 1 Battery bay Holds the primary battery. 2 Hard drive security screw Secures the hard drive in the hard drive bay. 3 Modem slot cover Contains the mini PCI modem card. 4 MultiBay notch Helps to grasp a drive or battery pack from the MultiBay. 5 MultiBay release latch Releases a removable drive or battery pack from the MultiBay. 6 Fan Provides airflow to cool internal components.
EasyPoint IV Pointing Stick Model Components Figure 1-8 EasyPoint IV Pointing Stick Model Components Table 1-11 Keyboard Components Pointing Stick Model Item Component Function 1 EasyPoint IV pointing stick Moves the cursor in the direction of finger movement. 2 Left pick button Functions like the left button on an external mouse. 3 Scroll button Scrolls the document to allow quicker maneuverability. 4 Right pick button Functions like a right button on an external mouse.
TouchPad Components Figure 1-9 TouchPad Components Table 1-12 Keyboard Components TouchPad Model Item Component Function 1 TouchPad Moves the cursor in the direction of finger movement. 2 Left TouchPad button Functions like the left button on an external mouse. 3 Right TouchPad button Functions like a right button on an external mouse.
1.4 Design Overview This section presents a design overview of key parts and features of the computer. For assembly/disassembly instructions for the parts described in this section, refer to Chapter 5.
1-22 Product Description
chapter 2 T ROUBLESHOOTING Follow these basic steps when beginning the troubleshooting process: 1. 2. 3. 4. Complete the preliminary steps listed in Section 2.1. Run the Power-On Self-Test (POST) as described in Section 2.3. Run Computer Setup as described in Section 2.5. If you are unable to run POST or if the problem persists after running POST, perform the recommended actions described in the diagnostic tables in Section 2.5.
2.1 Preliminary Steps IMPORTANT: Use AC power when running POST or Computer Setup. A low battery condition could initiate Hibernation and interrupt the test. Before running POST, complete the following steps: 1. Obtain established passwords. If you must clear the passwords, go to Section 2.2. 2. Ensure that the hard drive is installed in the computer. 3. Ensure that the battery pack is installed in the computer and the power cord is connected to the computer and plugged into an AC power source. 4.
2.2 Clearing Passwords 1. 2. 3. 4. 5. 6. 7. 8. 9. Turn off the computer. Disconnect the AC Adapter (refer to Section 5.3). Remove the battery pack (Section 5.6). Disconnect and remove the Real Time Clock (RTC) battery (Section 5.11). Wait five minutes. Reconnect the RTC battery. Install the keyboard deck and keyboard assembly. Reconnect the AC Adapter. Do not reinstall the battery pack yet. Turn on the computer. NOTE: Remember to set the date and time the next time the computer is turned on. 2.
2.4 POST Error Messages If the system is not functioning well enough to run POST, or if the display is not functioning well enough to show POST error messages, refer to the Troubleshooting tables in Section 2.6. If POST detects an error, one of the following events occurs: ■ ■ ■ A message with the prefix "WARNING" appears, informing you where the error occurred. The system pauses until you press F1 to continue. A message with the prefix "FATAL" appears, informing you where the error occurred.
Table 2-1 Warning Messages Message Description Recommended Action CMOS checksum invalid, run SCU CMOS RAM information has been corrupted. Run Computer Setup to reinitialize CMOS-RAM. CMOS failure, run SCU CMOS RAM has lost power. Run Computer Setup to reinitialize CMOS-RAM. Diskette controller error The diskette drive controller failed to respond to the recalibrate command.
Fatal errors emit a beep and may display a FATAL message. Fatal errors indicate severe problems, such as a hardware failure. Fatal errors do not allow the system to resume. Some of the Fatal error beep codes are listed at the end of this section. Table 2-2 Fatal Error Messages Message Description Beep code CMOS RAM test failed A walking bit test of CMOS RAM location 0E (Hex) - 3F (Hex) failed.
2.5 Compaq Utilities Compaq Utilities contain several functions that ■ ■ Determine if various computer devices are recognized by the system and are operating properly. Provide information about the system once it is configured. Compaq Utilities include the following programs: ■ ■ Computer Setup Compaq Diagnostics To access Compaq Utilities: 1. Turn on or restart the computer by clicking Start!Shut Down!Restart the computer. 2.
Using Computer Setup All information and settings in Computer Setup are accessed from the File, Security, or Advanced menus. NOTE: Your settings in Computer Setup are not affected by updating the system ROM. To view information or change a setting in Computer Setup: 1. Turn on or restart the computer. When the blinking cursor appears in the upper-right corner of the screen, press F10. ■ To change the language, press F2. ■ To view navigation information, press F1.
Security Menu Begin here To do this Setup password Enter, change, or delete a setup password. Power-On password Enter, change, or delete a power-on password. Password options Enable/disable: ■ QuickLock/QuickBlank. ■ Lock keyboard and pointing stick or touchpad at startup. (These features can be enabled only when a power-on password is set.) DriveLock passwords Enter, change, or delete a DriveLock password. Device security Enable/disable ■ Ports or diskette drives. ■ Diskette write.
Advanced Menu Begin here To do this Language (or press F2) Change the Computer Setup language. Boot Options Enable/disable ■ QuickBoot, which starts the computer more quickly by eliminating some startup tests. (If you suspect a memory failure and want to test memory automatically during startup, you may want to disable QuickBoot.) MultiBoot, which enables you to set a startup sequence that can include any drives in the system. Device Options ■ Enable/disable the embedded numeric keypad at startup.
Using Compaq Diagnostics for Windows 1. Access Compaq Diagnostics for Windows by selecting Start!Settings!Control Panel!Compaq Diagnostics. 2. To select a category, choose one of two methods: ■ Select the Categories menu, then select a category from the drop-down list. ■ Select a category icon on the toolbar. 3. To run diagnostic tests a) Select the Test tab. b) In the scroll box, select the category or device you want to test. c) Select the Quick, Complete, or Custom test type.
Table 2-5 Ports Serial port 3F8, IRQ4 Infrared port 2F8, IRQ9 Parallel port 378, IRQ7 Ethernet port 300, IRQ11 Table 2-6 Power Low Battery Warning Beep Checked (enabled) External Energy Saving Monitor Connected Unchecked (not connected) Power Management Enabled While operating on battery power Conservation Level High Level Definition High Suspend Time: 3 minutes Hibernation Timeout: Immediate Drive Timeout: 1 minute Screen Timeout: 1 minute Medium Suspend Time: 5 minutes Hibernation Timeo
2.6 Troubleshooting Without Diagnostics This section provides information about how to identify and correct some common hardware, memory, and software problems. It also explains several types of messages that may be displayed on the screen. Since symptoms can appear to be similar, carefully match the symptoms of the computer malfunction against the problem description in the Troubleshooting tables to avoid a misdiagnosis.
Checklist for Solving Problems If you encounter a minor problem with the computer or software applications, go through the following checklist for possible solutions: ■ ■ ■ ■ ■ Is the computer connected to an external power source, or does it have a fully charged battery pack installed? Are all cables connected properly and securely? Did the diskette drive contain a nonbootable diskette when you turned on the computer? Have you installed all the needed device drivers? For example, if you are using a mouse,
Table 2-8 Solving Audio Problems Problem Possible Cause Solution Computer does not beep after the Power-On SelfTest (POST). System beeps have been turned down. Use the Fn+F5 hotkeys to turn up the system volume. Internal speaker does not Volume may be turned off or produce sound when an set too low. external audio source is connected to the stereo line-jack. Line input may not be connected properly. " " Adjust the overall volume by pressing the Fn+F5 hotkeys.
Table 2-9 Solving Battery/Battery Gauge Problems Problem Possible Cause Solution Computer is beeping and battery power light is blinking Battery pack charge is low. ■ Charge Computer battery charge Volume turned down too light blinks to indicate low low. battery condition, but computer does not beep. Battery pack will not charge. Battery pack was exposed to temperature extremes. Battery pack is already charged. the battery pack by connecting to an external power source.
Table 2-10 Solving Compact Disc and DVD-ROM Problems Problem Possible Cause Solution Drive cannot read a disc Disc is not properly seated in the drive. Open the loading tray, insert the disc, then close the tray. Disc is loaded in the loading Open the loading tray, turn over the tray upside down. disc (label facing up), then close the tray. CD-ROM drive or DVDROM drive is not detected by the computer. Disc has a scratch on its surface. Insert a different disc. Drive is not connected properly.
Table 2-12 Solving Hard Drive Problems Problem Possible Cause Solution Accessing information on the hard drive is much slower than usual. Hard drive entered low power state due to timeout and is now exiting from it. Wait for the system to restore the previously saved data to its state prior to initiating a low power state. Hard drive is fragmented/not Run ScanDisk and Disk Defragmenter. optimized or has errors. Hard drive does not work. Hard drive is not seated properly.
Table 2-13 continued Problem Possible Cause Solution Cannot communicate with another computer (continued). There is a conflict with the # bits. Select the same # bits setting for both computers. There is a stop byte conflict. Cannot transmit data. Infrared port doesn’t work. Select the same stop byte for both computers. There is a parity conflict. Select the same parity setting for both computers. Direct sunlight, fluorescent Remove the interfering light light, or flashing incandescent source(s).
Table 2-15 Solving Modem Problems Problem Possible Cause Modem loses connection. The cable connection from Check to make sure the telephone the phone line to the modem cable is properly connected. is loose. Call Waiting has not been disabled. Solution Disable Call Waiting: 1. Select Start ! Setting ! Control Panel ! select Modems. 2. From the General tab of the Modems Properties page, select Dialing Properties.
Table 2-15 Continued Problem Possible Cause Phone line noise causing Hang-up Delay S Register a disconnection. (S10) set too low. Solution Change S10 default to 150. To set S10=150: 1. Select Start ! Programs ! Accessories ! HyperTerminal, then go to Command Mode. 2. Type ATS10=150 and press Enter. This command causes the modem to take longer to disconnect even if there is noise on the line. No dial tone Phone service is not connected to the telephone wall jack.
Table 2-15 Continued Problem Modem does not connect at highest speed. Possible Cause Solution Line conditions in your area Have your telephone line checked or in the area you are calling by your local telephone service may not support the highest provider. connect speeds. Try dialing an alternate telephone number for the service you are using. Another device on your telephone line may be causing interference.
Table 2-16 Solving PC Card Problems Problem Possible Cause Solution Computer does not beep when a PC Card is inserted. PC Card is not inserted properly. Try reinserting the card. Ensure that the PC Card is inserted in the correct orientation. Insert the card gently to prevent damage to the pins. Speakers are turned off or volume is turned down. Adjust the volume control on the computer. PC Card or card driver is not Contact your Compaq authorized dealer, PCMCIA compliant.
Table 2-17 Solving Power Problems Problem Possible Cause Solution Computer will not turn on. Battery is discharged and computer is not connected to a power source. ■ Charge the battery pack. ■ Replace the battery pack. ■ Connect the computer to an external power source. Battery is discharged and Ensure that cables connecting the cables to the external power computer and the external power source are unplugged. source are plugged in properly. Computer turned off while it was left unattended.
Table 2-19 Solving USB Problems Problem Possible Cause Solution External device connected to a USB connector does not work. The operating system limits external devices connected by USB to two tiers which can include no more than two hubs on the first tier and no more than one keyboard and one pointing device on the first or second tier.
2-26 Troubleshooting
chapter 3 I LLUSTRATED P ARTS C ATALOG This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers for the Compaq Armada M700 Series of Personal Computers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer (Figure 3-1). Figure 3-1.
3.2 Computer System Major Components Figure 3-2.
Table 3-1 Spare Parts: Computer System Major Components Item 1 2 3 4 5a 5b 6 7 Description Spare Part Number Display assembly 14.1-inch, XGA, CTFT 135219-001 13.
Computer System Major Components (continued) 3-4 Illustrated Parts Catalog
Table 3-1 continued Item 8a 8b 9 10 11 12 Description Spare Part Number Cable Kit, includes: RAM board not illustrated: Real time clock (RTC) microphone assembly battery microphone cable Infrared board (includes RJ-11 and RJ-45 jacks) Fan Voltage converter board used with the following SKUs: 470011-XXX 215199-XXX 215198-XXX 215191-XXX 215197-XXX used with the following SKUs: 140141-XXX 205858-XXX 139114-XXX 139116-XX2 140142-XXX 205860-XXX 139116-XX6 159695-XXX 205861-XXX 139116-XX8 205862-XXX 159696-XX
Computer System Major Components (continued) 3-6 Illustrated Parts Catalog
Table 3-1 continued Item Description 12 System board (continued; includes processor assembly) supports Intel Mobile Pentium III 450-MHz with MMX technology; used with the following SKUs: 139117-XXX 139120-XXX 140142-XXX 159696-XXX 159697-XXX 159695-XXX supports Intel Mobile Pentium II 400-MHz with MMX technology; used with the following SKUs: 124939-XX2 124940-XX4 124941-XX6 400322-XX6 400323-XX6 400324-XX4 400325-XXX 400326-XX2 400327-XX2 supports Intel Mobile Pentium II 366-MHz with MMX technology; use
3.3 Plastics Kit Components Figure 3-3.
Table 3-2 Plastics Kit Components Spare Part Number 135230-001 Item 1a 1b 2 Description Switch cover without Easy Access buttons; used with the following SKUs: 124898-XXX 149208-XXX 400322-XXX 124899-XXX 152550-XXX 400323-XXX 124938-XXX 159695-XXX 400324-XXX 124939-XXX 159696-XXX 400325-XXX 124940-XXX 159697-XXX 400326-XXX 124941-XXX 164462-XXX 400327-XXX 139114-XXX 205860-XXX 400328-XXX 139116-XXX 205861-XXX 400329-XXX 139117-XXX 205862-XXX 400330-XXX 139120-XXX 205857-XXX 400331-XXX 140141-XXX 205858-X
3.4 Cable Kit Components Figure 3-4.
3.5 Mass Storage Devices Figure 3-5. Mass Storage Devices Table 3-4 Spare Parts: Mass Storage Devices Item Description 1 Hard drive 30.0 GB 20.0 GB 18.0 GB 12.0 GB 10.0 GB 2 3 4 5 6 6.4 GB 6.0 GB; used only with SKUs 205857-XXX and 205858-XXX 24-speed Max CD-ROM drive 20-speed Max CD-RW drive (not illustrated) 8-speed Max DVD-ROM drive 4-speed Max DVD-ROM drive Diskette drive, 1.44-megabyte, 3.
3.6 Miscellaneous Table 3-5 Spare Parts: Miscellaneous (not illustrated) Description Spare Part Number Armada M700 Maintenance & Service Guide Battery Charger Cables Automobile Power Adapter/Charger cable Aircraft Power Adapter cable Composite TV cable RJ11 modem cable RJ45 modem cable Hard Drive Adapter Logo Kit Memory expansion board 256 MB 128 MB 64 MB 32 MB Miscellaneous Screw Kit Modems Mini PCI modem board, V.90, Type-I Mini PCI combination modem/network interface card (NIC), V.
chapter 4 R EMOVAL AND R EPLACEMENT P RELIMINARIES This chapter provides essential information for proper and safe removal and replacement service. 4.1 Tools Required You will need the following tools to complete the removal and replacement procedures: ■ ■ Magnetic Torx T-8 screwdriver (for all screws unless otherwise specified) 9/32-inch socket for bushing guides 4.
Cables and Connectors Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Ensure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; they tear easily.
4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases the discharge contains enough power to alter device parameters or melt silicon junctions. A sudden discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Workstation Precautions Use the following grounding precautions at workstations: ■ ■ ■ ■ ■ ■ ■ ■ Cover the workstation with approved static-dissipative material (refer to Table 4-2 later in this chapter). Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. Use field service tools, such as cutters, screwdrivers, and vacuums that are conductive.
Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, a strap must be worn snug against the skin. On grounded mats with banana-plug connectors, connect a wrist strap with alligator clips.
Electrostatic Voltage Levels and Protective Materials Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
chapter 5 R EMOVAL AND R EPLACEMENT P ROCEDURES 5.1 Serial Number The computer serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is located on the bottom of the computer. Figure 5-1.
5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing the components from the computer. 5.3 Disconnecting the Computer 5.4 Computer Feet 5.5 Preparing the Computer for Disassembly 5.6 Battery Packs Removing a Battery Pack Inserting a Battery Pack 5.7 Hard Drives Removing a Hard Drive Inserting a Hard Drive 5.8 MultiBay Devices Removing MultiBay Devices Inserting MultiBay Devices Inserting a Hard Drive in the MultiBay Adapter 5.
5.3 Disconnecting the Computer 1. 2. 3. 4. 5. 6. Shut down the computer. Close the computer. Position the computer so the rear panel faces forward. Disconnect the power cord from the AC Adapter ! (Figure 5-3). Disconnect the power cord from the wall outlet ". Disconnect the AC Adapter cord from the computer #. Figure 5-3. Disconnecting the Computer 7. Turn off and disconnect external devices.
5.4 Computer Feet The computer feet are oval, adhesive-backed rubber pads. The computer feet are included in the Miscellaneous Plastic Spare Kit. Install the feet by removing the protective covering from the adhesive back an attaching the feet to the bottom of the computer (Figure 5-4). NOTE: The front left computer foot adheres to the bottom of the battery pack. Figure 5-4.
5.5 Preparing the Computer for Disassembly 1. Shut down the computer. 2. Disconnect the AC Adapter and all external devices connected to the computer. 3. Remove the battery pack from the battery bay (Section 5.6). CAUTION: Failure to disconnect the AC Adapter from the computer and remove the battery pack before removing and installing internal components can damage the equipment. 4. Remove the hard drive (Section 5.7). 5. Remove MultiBay devices (Section 5.8).
5.6 Battery Packs ! WARNING: To reduce the risk of injury or damage to the battery pack, do not crush, puncture, or incinerate the battery pack or short the metal contacts. Do not attempt to open or service the battery pack. Removing a Primary Battery Pack from the Battery Bay 1. If the computer is turned on, press the suspend button. If there is hard drive or diskette activity, Suspend may not occur immediately.
Inserting a Primary Battery Pack in the Battery Bay CAUTION: To prevent damage to the computer, do not insert a battery pack until the computer is fully reassembled. 1. Close the computer. 2. Tilt the computer up ➊ (Figure 5-6). 3. With the smooth side of the battery pack facing up and the battery cells facing in, lead the rounded edge of the battery pack into the battery bay. Angle the battery pack into the bay until it is fully seated ➋. Figure 5-6. Inserting a Battery Pack 4.
5.7 Hard Drives Removing a Hard Drive from the Hard Drive Bay Before removing a hard drive, back up all information on the hard drive. 1. Save all work, exit all applications, and shut down the computer. 2. Tilt the computer at an angle ➊ so the bottom of the computer is accessible (Figure 5-7). 3. If the hard drive has been secured in the hard drive bay with a security screw ➋, remove the screw using the security screwdriver provided with the computer. Figure 5-7.
4. Push down on the hard drive bezel on the front of the hard drive ➊ (Figure 5-8). 5. Lift the bezel up 90 degrees to create a handle ➋. Pull the hard drive out of the hard drive bay. Figure 5-8.
Inserting a Hard Drive into the Hard Drive Bay 1. With the hard drive bezel pulled down, slide the hard drive into the hard drive bay ➊ until the drive is seated (Figure 5-9). 2. Push up on the hard drive bezel to secure the hard drive in the bay ➋. Figure 5-9. Inserting a Hard Drive 3. If the hard drive was secured in the hard drive bay using a security screw, replace the screw.
5.8 MultiBay Devices Removing MultiBay Devices 1. Save all work, exit all applications, and shut down the computer. 2. Remove the media (diskette, CD-ROM, DVD-ROM) from the drive. Be sure the drive tray is closed. 3. Tilt the computer at an angle ➊ so the bottom of the computer is accessible (Figure 5-10). 4. Slide the MultiBay release latch ➋ forward. 5. Pull the device out of the MultiBay ➌. Figure 5-10.
Inserting MultiBay Devices 1. Remove the media (diskette, CD-ROM, etc.) from the drive to be inserted into the MultiBay. Ensure that the CD tray is closed. 2. With the bezel facing out, slide the device into the MultiBay until it clicks into place (Figure 5-11). Figure 5-11.
Inserting a Hard Drive into the MultiBay Adapter Before a hard drive can inserted into the MultiBay, it must first be placed in the hard drive MultiBay adapter. 1. Push the adapter slide tabs ➊ toward the outside of the adapter (Figure 5-12). 2. Place the hard drive, label up, into the adapter ➋, and slide the drive connector toward the adapter connector ➌ until the drive is seated. 3. Release the adapter slide tabs. Figure 5-12.
5.9 PC Cards The procedure for removing PC Cards varies with the operating system being used and with the kind of PC Card being removed. If Windows 95 or Windows 98 is running: ■ ■ A PC Card can be removed while the computer is on or off. The PC Card icon appears in the system tray on the Windows taskbar only while a PC Card is inserted. If Windows NT is running: ■ Some PC Cards, such as modem, ATA, flash, and SRAM cards, can be removed while the computer is on.
Removing a PC Card If you are running Windows 95 or Windows 98, you do not need to turn off the computer or initiate Suspend before removing a PC Card. CAUTION: If you are running Windows 95 or Windows 98, you should always stop PC Cards before removing them to prevent damage to the PC Card or computer. If you are running Windows NT 4.0 without CardWare provided by Compaq, you must turn off the computer before removing a PC Card. To remove a PC Card from the computer: 1.
Inserting a PC Card 1. Save all work, exit all applications, and turn off the computer. 2. Open the PC Card door by flipping it down (Figure 5-14). 3. Align the edges of the PC Card with the rails on the sides of one of the PC Card slots. 4. Insert the PC Card into the PC Card slot until it is seated. Figure 5-14.
5.10 Modem/Combo Card The computer can be equipped with a modem card, a network interface card (NIC), or a combination modem/NIC (modem/combo) card. 1. Prepare the computer for disassembly (Section 5.5). 2. Turn the computer bottom side up with the rear panel facing forward. 3. Remove the two screws ➊ that secure the modem/combo card cover to the base assembly (Figure 5-15). 4. Swing the right side of the cover up and to the left ➋. Figure 5-15.
5. Lift the left side of the modem/combo card to disconnect it from the system board. Swing the card to the right ➊ (Figure 5-16). 6. Disconnect the LAN and modem connectors from the card ➋. Figure 5-16. Removing a Modem/Combo Card Reverse the above procedure to install the modem/combo card and its cover.
5.11 RTC Battery 1. 2. 3. 4. Save all work, exit all applications, and shut down the computer. Remove the modem/combo card cover and the modem/combo card (Section 5.10). Disconnect the RTC battery cable from the system board ➊ (Figure 5-17). Remove the battery from the base assembly ➋. Figure 5-17. Disconnecting the RTC Battery Cable Reverse the above procedure to replace the RTC battery.
5.12 Keyboard ! WARNING: Failure to unplug the power cord and remove the battery pack before installing a memory expansion board can damage the equipment and expose you to the risk of electrical shock. CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning this procedure, ensure that you are properly grounded. For more information, refer to Section 4.4 “Preventing Electrostatic Damage.” 1. Prepare the computer for disassembly (Section 5.5). 2. Open the computer. 3.
5. Release the Zero Insertion Force (ZIF) connector to which the keyboard cable is connected ➊ (Figure 5-19). 6. Disconnect the keyboard cable from the connector on the system board ➋. 7. Release the ZIF connector to which the pointing device cable is connected ➌ (EasyPoint IV models only). 8. Disconnect the pointing device cable from the connector on the top cover ➍ (EasyPoint IV models only). Figure 5-19. Disconnecting the Pointing Device and the Keyboard Cables 9. Remove the keyboard.
5.13 Memory Expansion The memory compartment is located underneath the keyboard and contains two memory slots. The computer standard memory is contained in one slot. Computer memory can be expanded by installing a memory board in the empty slot and/or replacing the standard memory board. SDRAM memory boards are available in 32-, 64-, and 128-MB increments. Removing a Memory Expansion Board 1. Pull away the plastic retention clips ➊ on each side of the memory expansion board.
Installing a Memory Expansion Board All memory expansion boards supported by the computer can be used in either of the two memory expansion slots. The memory expansion boards are also all keyed (notched) to ensure correct positioning. 1. Insert the memory expansion board into an empty memory expansion slot at a 45-degree angle ➊. Slide it into place until it is seated while tilted (Figure 5-21). 2. Push the memory expansion board down until the plastic retention clips ➋ snap into place. Figure 5-21.
5.14 Switch Cover 1. 2. 3. 4. Prepare the computer for disassembly (Section 5.5). Remove the keyboard (Section 5.12). Position the computer so the rear panel faces forward. Remove the two screws from the rear panel of the computer that secure the switch cover to the base assembly (Figure 5-22). Figure 5-22. Removing the Switch Cover Screws 5. Position the computer so the front faces forward. 6. Open the computer as far as it will open.
7. Lift the switch cover straight up (Figure 5-23). Figure 5-23. Removing the Switch Cover Reverse the above procedure to install the switch cover.
5.15 Display Assembly NOTE: To prevent the computer from tipping over during removal of the display assembly, a MultiBay device can be inserted into the computer MultiBay. 1. Prepare the computer for disassembly (Section 5.5). 2. Remove the keyboard (Section 5.12). 3. Remove the switch cover (Section 5.14). 4. Disconnect the audio/microphone cable ➊ (Figure 5-24). 5. Disconnect the display cable ➋. 6. Disconnect the inverter cable ➌. Figure 5-24.
7. Position the computer so the rear panel faces forward. 8. Remove the two screws that secure the display assembly to the base assembly (Figure 5-25). Figure 5-25.
9. Lift the display assembly straight up (Figure 5-26). Figure 5-26. Removing the Display Assembly Reverse the above procedure to install the display assembly.
5.16 Top Cover 1. 2. 3. 4. 5. 6. Prepare the computer for disassembly (Section 5.5). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Turn the computer bottom side up with the front of the computer facing forward. Remove the six screws from the bottom of the computer (Figure 5-27). Figure 5-27. Removing the Top Cover Screws 7. Turn the computer top side up with the front of the computer facing forward.
8. Remove the four screws securing the top cover to the computer base (Figure 5-28). Figure 5-28.
9. Disconnect the pointing device button cable ➊ (Figure 5-29). 10. Disconnect the right ➋ and left ➌ speaker cables. 11. Partially lift the top cover. 12. Disconnect the LED board cable ➍. 13. Remove the top cover. Figure 5-29. Removing the Top Cover Reverse the above procedures to install the top cover.
The top cover must be removed before the LED board can be removed. 1. Remove the two screws ➊ securing the LED board to the top cover (Figure 5-30). 2. Remove the LED board from the top cover ➋. Figure 5-30. Removing the LED Board Reverse the above procedures to install the LED board.
5.17 USB Board 1. 2. 3. 4. 5. 6. 7. 8. 9. Prepare the computer for disassembly (Section 5.5). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Remove the top cover (Section 5.16). Position the computer so the rear panel faces forward. Remove the screw that secures the USB board to the base assembly ➊ (Figure 5-31). Disconnect the USB cable ➋. Lift up on the left side of the board.
5.18 Voltage Converter Board 1. 2. 3. 4. 5. 6. Prepare the computer for disassembly (Section 5.5). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Remove the top cover (Section 5.16). Lift up on the front and right side of the voltage converter board to disconnect it from the system board (Figure 5-32). 7. Remove the voltage converter board. Figure 5-32.
5.19 Infrared Board 1. 2. 3. 4. 5. 6. Prepare the computer for disassembly (Section 5.5). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Remove the top cover (Section 5.16). Remove the screw that secures the infrared board to the base assembly ➊ (Figure 5-33). 7. Remove the infrared board assembly ➋. Figure 5-33. Removing the Infrared Board Assembly Reverse the above procedure to connect the voltage converter board.
5.20 System Board 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Prepare the computer for disassembly (Section 5.5). Remove the modem/combo card (Section 5.10). Remove the RTC battery (Section 5.11). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Remove the top cover (Section 5.16). Remove the USB board (Section 5.17). Remove the voltage converter board (Section 5.18). Remove the infrared board (Section 5.19).
13. Disconnect the memory bracket/connector by lifting up on the left side ➊ (Figure 5-35). 14. Remove the screw underneath the memory bracket/connector that secures the system board to the base assembly ➋. 15. Remove the two screws that secure the system board to the base assembly ➌. Figure 5-35.
16. Remove the two screws that secure the PC Card assembly to the base assembly (Figure 5-36). Figure 5-36.
17. Lift straight up on the system board to remove it from the base assembly (Figure 5-37). Figure 5-37. Removing the System Board Reverse the above procedure to install the system board.
5.21 Fan 1. 2. 3. 4. 5. 6. 7. 8. 9. Prepare the computer for disassembly (Section 5.5). Remove the modem/combo card (Section 5.10). Remove the RTC battery (Section 5.11). Remove the keyboard (Section 5.12). Remove the switch cover (Section 5.14). Remove the display assembly (Section 5.15). Remove the top cover (Section 5.16). Remove the USB board (Section 5.17) Remove the system board (Section 5.19). 10. Disconnect the fan cable from the system board (Figure 5-38). Figure 5-38.
12. Remove the screw ➊ that secures the fan to the system board (Figure 5-39). 13. Remove the fan ➋. Figure 5-39. Removing the Fan Reverse the above procedure to install the fan to the system board.
5-42 Removal and Replacement Procedures
chapter 6 S PECIFICATIONS 6.1 Physical and Environmental Table 6-1 Computer Dimensions Height Depth Width Weight (depends on configuration) Standalone (Battery) Power Requirements Nominal operating voltage Average operating power Peak operating power AC Adapter Power Requirements Operating voltage Operating current Operating frequency range Maximum output voltage Maximum transient Temperature Operating Nonoperating Relative Humidity (noncondensing) Operating Nonoperating (tw = 101.6°F/38.
6.2 Displays Table 6-2 14.1-inch XGA, CTFT Display U.S. Metric Dimensions Height Width Diagonal 8.46 in. 11.22 in. 14.10 in. 21.50 cm 28.50 cm 35.81 cm Number of Colors up to 16.8 million Contrast Ratio 150:1 Brightness 120 nits, 150 nits typical Pixel Resolution Pitch Format Configuration 1024 × 768 RGB Stripe Backlight Edge Lit, bottom Character Display 80 × 25 Total Power Consumption 4.2 W / Inverter (max) 125 CD/M 2 0.264 × 0.264 mm Table 6-3 13.3-inch XGA, CTFT Display U.S.
6.3 Hard Drives Table 6-4 Hard Drives 6.4 GB 10.0 GB 12.0 GB 20.0 GB 30.0 GB User capacity per 1 drive 6.4 GB 10.0 GB 12.0 GB 20.0 GB 30.0 GB Form factor 2.5 inches 2.5 inches 2.5 inches 2.5 inches 2.5 inches Drive height (with drive frame, in mm) 9.5 9.5 9.5 9.5 12.5 Drive width (with drive frame, in mm) 70 70 70 70 70 Interface type ATA-4 ATA-4 ATA-4 ATA-5 ATA-5 2.5 ms 12.0 ms 23.0 ms 2.5 ms 12.0 ms 23.0 ms 2.5 ms 12.0 ms 23.
6.4 Diskette Drive Table 6-5 Diskette Drive Diskette Size High Density Low Density 3.5 in. 1.44 MB/1.2 MB 720 KB Light None Height 0.50 in / 12.7 mm Bytes per Sector 512 Sectors per Track Hight Density Low Density 18 (1.44 MB)/15 (1.2 MB) 9 Tracks per Side High Density Low Density 80 (1.44 MB)/80 (1.
6.5 CD-ROM Drive Table 6-6 CD-ROM Drive Applicable Disc CD-ROM (Mode 1, 2, and 3) CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and Form 2) CD-R (read only) CD Plus Photo CD (single/multisession) CD Extra Video CD CD-WO (fixed packets only) CD-Bridge Center Hole Diameter .59 in./15 mm Disc Diameter 12 cm, 8 cm Disc Thickness 1.2 mm Track Pitch 1.6 µm Laser Beam Divergence Output Power Type Wave Length 53.5 ± 1.5 degrees 0.24 ± 0.
6.6 DVD-ROM Drive Table 6-7 DVD-ROM Specifications Applicable Disc DVD-5, DVD-9, DVD-10 CD-ROM mode 1, mode 2 CD-Digital Audio CD-XA mode 2 (Form 1, Form 2) CD-I mode 2 (Form 1 and Form 2) CD-I Ready CD-Bridge CD-R Photo CD (single/multisession) Center Hole Diameter .59 in./15 mm Disc Diameter 12 cm, 8 cm Disc Thickness 1.2 mm Track Pitch .74 µm Capacity DVD-5 DVD-9 DVD-10 Mode 1, 12 Mode 2, 12 cm 8 cm 4.7 GB 8.5 GB 9.
6.7 LS-120 Drive Table 6-8 LS-120 Drive 1.68 MB DMF 1.44 MB 1.2 MB 1.
6.8 Battery Pack Table 6-9 Lithium Ion Battery Pack U.S. Metric Dimensions Height Length Weight 0.57 in. 4.55 in. 3.93 in. 1.44 cm 11.50 cm 9.90 cm Weight 0.85 lb 0.39 kg Energy Voltage Amp-hour capacity Watt-hour capacity 14.4 V 2.8 Ah 40.
6.
6.11 System I/O Addresses Table 6-12 System I/O Addresses I/O Address (Hex) System Function (Shipping Configuration) 000 - 00F DMA Controller no. 1 010 - 01F Unused 020 - 021 Interrupt Controller no.
Table 6-12 continued I/O Address (Hex) System Function (Shipping Configuration) 201 Joystick (Decoded in ESS1688) 202 - 21F Unused 220 - 22F Entertainment Audio 230 - 26D Unused 26E - 26 National 87334 "Super IO" Controller in ArmadaStation/Armada MiniStation 278 - 27F 280 - 2AB Unused Unused 2A0 - 2A7 ArmadaStation/Armada MiniStation PC Card DMA 2A8 - 2E7 2F0 - 2F7 Selection, Hard Drive Reset, IDE Select, MultiBay Device Identification Unused Reserved Serial Port Unused 2F8 - 2FF Infrare
6.
appendix A C ONNECTOR P IN A SSIGNMENTS Table A-1 RJ-11 Connector Pin 1 2 3 4 5 6 7 8 1 3 5 7 2 4 6 8 Signal NC_J3A NC_J3B TIP RING NC_J3C NC_J3D Unused Unused Table A-2 Serial Connector 1 2 6 Pin 1 2 3 4 5 Signal Carrier Detect Receive Data Transmit Data Data Terminal Ready Ground 3 7 4 8 Pin 6 7 8 9 5 9 Signal Data Set Ready Ready to Send Clear to Send Ring Indicator Table A-3 Microphone Jack Connector Pin 1 2 1 Signal Audio in Ground 2 Connector Pin Assignments A-1
Table A-4 Stereo Speaker/Headphone Jack Connector Pin 1 2 1 Signal Audio out Ground 2 Table A-5 Stereo Line-in Jack Connector Pin 1 2 1 Signal Audio in Ground 2 Table A-6 Parallel Connector 13 12 25 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Signal Strobe Data Bit 0 Data Bit 1 Data Bit 2 Data Bit 3 Data Bit 4 Data Bit 5 Data Bit 6 Data Bit 7 Acknowledge Busy Paper End Select A-2 Connector Pin Assignments 11 24 10 23 9 22 8 21 7 20 6 19 Pin 14 15 16 17 18 19 20 21 22 23 24 25 5 18 4 17 3 16 2 1
Table A-7 Docking Connector 30 60 90 120 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal EBOXL AGND EBOXS1 RED AGND GREEN AGRD BLUE AGND VSYNC HSYNC DDC DAT DDC CLK GND INDEX RDATA TRK0 WDATA WGATE STEP DIR POWER ON SYS RESET GND DSKCHG +5 V (VDD) AUGND XA2/L IN XA3/R IN MID0/MIC IN AUGND XA0/L OUT XSD/MIC SN 1 31 61 91 Pin 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Signal XA1/R OUT GND GND EXPC
Table A-7 Continued Pin 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 Signal PDATA6 LD14 PDATA7 LD15 GND ERROR LCLK RXD1 LVREQ TXD1 LCREQ RTS1 LEN GND CTS1 LIIC CLK DTR1 LIIC DAT DSR1 EX DCD1 EX 12C DATA GND 12C CLK GND HDSEL GND WPROT EBOXS2 /GND ERDY EBOXL /GND FLUSHREQ MEMACK PS2 VCC SERIRQ PS2 CLK EXPREQ AD[29] AD[31] AD[30] AD[28] AD[26] GND AD[24] AD[22] AD[20] AD[18] Pin 105 106 107 108 109 110 111 112 113 114 115 116 117 118
Table A-7 Continued Pin 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 Signal VBATT AD[23] GND AD[21] AD[19] AD[17] GND AD[14] AD[12] AD[10] AD[08] GND AD[07] AD[05] AD[03] AD[01] GND Pin 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 Signal CBE3 CBE2 IRDY DEVSEL LOCK OERR SERR GND RSVD3 M 12C CLK M 12C DATA M RING MGND M DXTN GND M DXTP MSTRBAT Table A-8 External Keyboard/Mouse Connector Connector 6 5 4 3 KEY 2 1 Pin 1 2 3 4 5 6 Signal Keyboard/Mouse DAT
Table A-9 External Monitor Connector 5 4 10 15 Pin 1 2 3 4 5 6 7 8 Signal Red Analog Green Analog Blue Analog NC Ground Ground Ground Ground A-6 Connector Pin Assignments 3 14 2 8 KEY 13 1 7 12 Pin 9 10 11 12 13 14 15 6 11 Signal NC Ground NC DDC Data Horizontal Sync Vertical Sync DDC Clock
appendix B P OWER C ORD S ET R EQUIREMENTS 3-Conductor Power Cord Set The wide range input feature of the Compaq Armada M700 Series of Personal Computers permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set received with the computer meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the computer is used.
Country-Specific Requirements 3-Conductor Power Cord Set Requirements—By Country Country Accredited Agency Applicable Note Numbers Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan JIS 3 The Netherlands KEMA 1 Norway NEMKO 1 Sweden SEMKO 1 Switzerland SEV 1 United Kingdom BSI 1 United States UL 2 Notes 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.
Index diagnostics, 2-7 disassembly reference chart, 5-2 diskette drive cable illustrated, 3-11 spare part number, 3-11 illustrated, 3-11 spare part number, 3-11 specifications, 6-4 display switch, illustrated, 1-17 display assembly illustrated, 3-2 removal, 5-26 spare part number, 3-3 specifications, 6-2 docking connector illustrated, 1-13 pinout, A-3 DVD-ROM drive illustrated, 3-11 spare part number, 3-11 specifications, 6-6 battery bay, illustrated, 1-18 battery charge light, illustrated, 1-12 battery pa
G K grounding methods, 4-5 keyboard EasyPoint IV description, 1-19 illustrated, 3-2 spare part number, 3-3 removal, 5-20 TouchPad description, 1-20 illustrated, 3-2 spare part number, 3-3 keyboard connector illustrated, 1-13 pinout, A-5 H hard drive bay illustrated, 1-12 bezel, 5-9 illustrated, 3-2, 3-11 inserting into hard drive bay, 5-10 inserting into MultiBay adapter, 5-13 light, illustrated, 1-17 removing from hard drive bay, 5-8 security screw, illustrated, 1-18 spare part number, 3-7, 3-11 hardwa
P R packaging precautions, 4-3 parallel connector illustrated, 1-13 pinout, A-2 password clearing, 2-3 PC Card, 5-14 inserting, 5-16 removing, 5-15 slots, illustrated, 1-15 pick button, illustrated, 1-19 plastic parts, handling, 4-1 Plastics Kit components illustrated, 3-8 components, illustrated, 3-2 spare part number, 3-3, 3-9 pointing device caps spare part number, 3-12 ports, default settings, 2-12 POST (Power-On Self-Test), 2-3 error messages, 2-4 power cord spare part number, 3-7 cord set country-sp
U V universal serial bus (USB) board illustrated, 3-2 removal, 5-33 spare part number, 3-3 port illustrated, 1-13 USB board removal, 5-33 utilities, Compaq, 2-7 voltage converter board illustrated, 3-2 removal, 5-34 spare part number, 3-5 I-4 Index W warning messages, 2-5 web agent, 1-7 workstation precautions, 4-4
