User guide

•The Predicted Post-processed Accuracy (PPA) has been improved in the TerraSync Centimeter Edition software; with
baseline lengths of 10km, Horizontal PPA can now reach 1cm and Vertical PPA can now reach 2cm.
•Miscellaneous usability improvements.
Version 5.30 (February 2012)
• Support for the Trimble Juno series 3B and 3D handhelds.
• Support for the Trimble GeoXH Centimeter edition handheld.
• High Resolution Mode map display.
• An updated SatDGPS.ini file to match changes in the frequencies of Omnistar L-Band corrections satellites.
Version 5.21 (October 2011)
•Resolves an issue where positions were not being produced with Trimble Juno series handhelds, Trimble Nomad G
series
handhelds, and Trimble Yuma tablet computers when the internal receiver was configured to use Satellite Based
Augmentation System (SBAS) corrections.
Version 5.20 (August 2011)
• Installs and runs on all supported platforms, and connects to all supported receivers.
• The ability to collect point features using the new QuickPoint data collection mode.
• A new TerraSync Centimeter edition software, enabling you to connect to Land Survey R4, R6 Model 1, R6 Model 2, R8
Model 2, R8 Model 3, and 5800 Model 2 receivers.
• Land Survey support has been removed from the TerraSync Professional edition software.
Version 5.11 (August 2011)
Support for the Trimble GeoExplorer® 6000 series Chinese edition handhelds.
Version 5.10 (February 2011)
Version 5.10 of the TerraSync software includes the following new features and changes:
• Support for the GeoExplorer® 6000 series handheld.
Note – The TerraSync software version 5.10 installs and runs only on a GeoExplorer 6000 series handheld.
• The use of Smart Settings, to increase the precision of your data, and to minimize the effect of atmospheric interference
and poor satellite geometry.
• Using Smart Settings, the receiver uses all available GNSS information to determine which combination of satellites to
use to generate the best possible position for any given environment, without the need for you to adjust receiver settings
to match the conditions.
• The GPS Slider has been removed. Custom settings can still be configured if Smart Settings are not used.
• The ability to select whether base station data used for post-processing is GPS only, or GPS and GLONASS.
• The removal of the Use GLONASS option from the GNSS Settings form. The receiver will always log GLONASS data, if
the Trimble Floodlight™ satellite shadow reduction technology option is enabled and active on the receiver.
• The Plan view now shows GLONASS satellites as well as GPS satellites.
• The L2 SNR reported will be the L2C SNR if it is available, otherwise it will be the L2E SNR.
• The Velocity Filter settings have been removed.
Data logged using TerraSync software version 5.10 can only be downloaded and post-processed using GPS Pathfinder
Office software version 5.10 or the GPS Analyst™ extension for Esri ArcGIS Desktop software version 2.40.
Version 5.01 (January 2011)
Version 5.01 of the TerraSync software provides:
• Correct handling of the conditional attribute after selection of a graphical picklist attribute.
• Better handling of the file system ‘low memory’ condition on devices powered by the Windows Mobile® operating
system.
If you use the TerraSync software version 5.01 with the GPS Analyst extension version 2.20, make sure that you have
installed the latest Data Transfer utility (version 1.52) and that you have installed all available updates for the GPS Analyst
extension. Data logged using TerraSync software version 5.01 can only be downloaded and post-processed using
GPS Pathfinder Office software version 5.00 or the GPS Analyst extension
Version 5.0 (October 2010)