Specifications
Table Of Contents
- Compaq ProLiant 5500 and 5500R Maintenance and Service Guide
- Notice
- Contents
- About This Guide
- Chapter 1: Illustrated Parts Catalog
- Chapter 2: Removal and Replacement Procedures
- Electrostatic Discharge Information
- Symbols in Equipment
- Preparation Procedures
- Caster Mounting Plate (Tower)
- Front Bezel Door (Tower)
- Fixed Front Bezel
- Side Access Panel
- Top Access Panel
- U-Channel Access Panel
- Fans
- Media Storage
- SCSI and CD-ROM Cable Connection Diagram
- Integrated Management Display (IMD)
- Power Switch with LED
- Processor, Processor Power Module, and Terminator Board Locations
- Processor Removal
- Processor Power Module
- Processor Terminator Modules
- Peripheral Board
- Memory
- 64-bit Dual Channel Wide Ultra2 SCSI Adapter
- Network Interface Controller (NIC)
- Hot-Plug Power Supply LED Indicators
- Hot-Plug Power Supply Cover Plate
- Power Backplane Board
- System I/O Board with Tray
- External Replacement Battery
- Chapter 3: Diagnostic Tools
- Diagnostic Tools Utility Overview
- Default Configuration
- Utilities Access
- Power-On Self-Test (POST)
- Diagnostics Software
- Steps for Diagnostics
- 100 – 199, Primary Processor Test Error Codes
- 200 – 299, Memory Test Error Codes
- 300 – 399, Keyboard Test Error Codes
- 400 – 499, Parallel Printer Test Error Codes
- 500 – 599, Video Display Unit Test Error Codes
- 600 – 699, Diskette Drive Test Error Codes
- 800 – 899, Monochrome Video Board Test Error Codes
- 1100 – 1199, Serial Test Error Codes
- 1200 – 1299, Modem Communications Test Error Codes
- 1700 – 1799, Hard Drive Test Error Codes
- 1900 – 1999, Tape Drive Test Error Codes
- 2400 – 2499, Advanced VGA Board Test Error Codes
- 6000 – 6099, Compaq Network Interface Controller Boards Test€Error Codes
- 6500 – 6599, SCSI Hard drive Test Error Codes
- 6600 – 6699, SCSI/IDE CD-ROM Drive Test Error Codes
- 6700 – 6799, SCSI Tape Drive Test Error Codes
- 7000 – 7099, Server Manager/R Board Test Error Codes
- 8600 – 8699, Pointing Device Interface Test Error Codes
- Array Diagnostic Utility (ADU)
- Integrated Management Log
- Rapid Error Recovery
- Remote Service Features
- ROMPaq Error Recovery Options
- Compaq Insight Manager
- Chapter 4: Connectors, Switches, LEDs, and Jumpers
- Chapter 5: Physical and Operating Specifications
- System Unit
- Dual Inline Memory Modules (DIMMs)
- 1.44-MB Diskette Drive
- 24X or Greater IDE CD-ROM Drive
- Integrated Dual-Channel Wide Ultra SCSI Controller
- 64-bit Dual Channel Wide Ultra2 SCSI Adapter
- Smart Array 3200 Controller
- Compaq 10/100 TX PCI Intel UTP Controller (NIC)
- Compaq 10/100 TX PCI UTP Controller (NIC)
- Non-Hot-Plug Ultra2 Hard Drives
- Non-Hot-Plug Wide-Ultra Hard Drives
- Hot Plug Ultra2 Hard Drives
- Hot-Plug Wide-Ultra Hard Drives
- Index
Diagnostic Tools 3-9
For use with Pentium II and Pentium III Xeon processor-based servers only
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
L=Long S=Short
Probable Source of Problem Recommended Action
175-
Configuration/Slot
Mismatch Device
Found
None EISA or PCI board added,
configuration not updated.
Run the System Configuration
Utility and correct.
177-Configuration
Not Complete
None Incomplete System
Configuration.
Run the System Configuration
Utility and correct.
178-Processor
Configuration Invalid
None Processor type or step does not
match configuration memory.
Run the System Configuration
Utility and correct.
180-Log Reinitialized None N/A N/A
201-Memory Error None RAM failure. Run Diagnostics. Replace failed
assembly as indicated.
203-Memory
Address Error
None RAM failure. Run Diagnostics. Replace failed
assembly as indicated.
207-Invalid Memory
Configuration -
Check DIMM [SIMM]
Installation
None Memory module installed
incorrectly.
Verify placement of memory
modules.
208-Invalid Memory
Speed - Check DIMM
[SIMM] Installation
1L, 1S The speed of the memory is too
slow, where: xx00 = expansion
board SIMMs are too slow, or
00yy = system board SIMMs are
too slow. xx and yy have
corresponding bit set.
The speed of the memory
modules must be 60 ns. Verify
the speed of the memory
modules installed and replace.
209-Memory
Detection Failure.
Check Memory
Installation
1L, 1S Unable to size memory. Check DIMM installation. If error
persists, replace DIMM.
211-Cache Switch
Set Incorrectly
None Switch not set properly during
installation or upgrade.
Verify switch settings.
212-System
Processor
Failed/Mapped out
1S Processor in slot x failed. Run Diagnostics and replace
failed processor.
214-DC-DC
Converter Failed
None PowerSafe Module (DC-DC
Converter) failed.
Run Diagnostics. Replace failed
assembly as indicated.
214-Processor PPM
Failed Module X
None Indicated PPM (DC-DC Converter)
failed.
Replace failed assembly as
indicated.
215-Processor Power
Module has lost
Redundancy in
Socket x
None PPM (DC-DC Converter) has lost
redundancy.
Run Diagnostics. Replace failed
assembly as indicated.
215-Nonfunctioning
Voltage Regulator
Module for
Processors
None PPM (DC-DC Converter) has
failed or lost redundancy.
Run Diagnostics. Replace failed
assembly as indicated.
continued