Specifications
Table Of Contents
- Compaq ProLiant 5500 and 5500R Maintenance and Service Guide
- Notice
- Contents
- About This Guide
- Chapter 1: Illustrated Parts Catalog
- Chapter 2: Removal and Replacement Procedures
- Electrostatic Discharge Information
- Symbols in Equipment
- Preparation Procedures
- Caster Mounting Plate (Tower)
- Front Bezel Door (Tower)
- Fixed Front Bezel
- Side Access Panel
- Top Access Panel
- U-Channel Access Panel
- Fans
- Media Storage
- SCSI and CD-ROM Cable Connection Diagram
- Integrated Management Display (IMD)
- Power Switch with LED
- Processor, Processor Power Module, and Terminator Board Locations
- Processor Removal
- Processor Power Module
- Processor Terminator Modules
- Peripheral Board
- Memory
- 64-bit Dual Channel Wide Ultra2 SCSI Adapter
- Network Interface Controller (NIC)
- Hot-Plug Power Supply LED Indicators
- Hot-Plug Power Supply Cover Plate
- Power Backplane Board
- System I/O Board with Tray
- External Replacement Battery
- Chapter 3: Diagnostic Tools
- Diagnostic Tools Utility Overview
- Default Configuration
- Utilities Access
- Power-On Self-Test (POST)
- Diagnostics Software
- Steps for Diagnostics
- 100 – 199, Primary Processor Test Error Codes
- 200 – 299, Memory Test Error Codes
- 300 – 399, Keyboard Test Error Codes
- 400 – 499, Parallel Printer Test Error Codes
- 500 – 599, Video Display Unit Test Error Codes
- 600 – 699, Diskette Drive Test Error Codes
- 800 – 899, Monochrome Video Board Test Error Codes
- 1100 – 1199, Serial Test Error Codes
- 1200 – 1299, Modem Communications Test Error Codes
- 1700 – 1799, Hard Drive Test Error Codes
- 1900 – 1999, Tape Drive Test Error Codes
- 2400 – 2499, Advanced VGA Board Test Error Codes
- 6000 – 6099, Compaq Network Interface Controller Boards Test€Error Codes
- 6500 – 6599, SCSI Hard drive Test Error Codes
- 6600 – 6699, SCSI/IDE CD-ROM Drive Test Error Codes
- 6700 – 6799, SCSI Tape Drive Test Error Codes
- 7000 – 7099, Server Manager/R Board Test Error Codes
- 8600 – 8699, Pointing Device Interface Test Error Codes
- Array Diagnostic Utility (ADU)
- Integrated Management Log
- Rapid Error Recovery
- Remote Service Features
- ROMPaq Error Recovery Options
- Compaq Insight Manager
- Chapter 4: Connectors, Switches, LEDs, and Jumpers
- Chapter 5: Physical and Operating Specifications
- System Unit
- Dual Inline Memory Modules (DIMMs)
- 1.44-MB Diskette Drive
- 24X or Greater IDE CD-ROM Drive
- Integrated Dual-Channel Wide Ultra SCSI Controller
- 64-bit Dual Channel Wide Ultra2 SCSI Adapter
- Smart Array 3200 Controller
- Compaq 10/100 TX PCI Intel UTP Controller (NIC)
- Compaq 10/100 TX PCI UTP Controller (NIC)
- Non-Hot-Plug Ultra2 Hard Drives
- Non-Hot-Plug Wide-Ultra Hard Drives
- Hot Plug Ultra2 Hard Drives
- Hot-Plug Wide-Ultra Hard Drives
- Index
Index 7
For use with Pentium II and Pentium III Xeon processor-based servers only
694-XX 3-26
697-XX 3-26
698-XX 3-26
699-XX 3-26
7000-11 3-34, 3-35
7000-12 3-34, 3-35
7000-13 3-34, 3-35
7000-14 3-34, 3-35
7000-15 3-34, 3-35
7000-21 3-34, 3-35
7000-22 3-34, 3-35
7000-23 3-34, 3-35
7000-24 3-34, 3-35
802-XX 3-27
824-XX 3-27
8601-xx 3-35
A Critical Error occurred prior to
this power-up 3-8
Abnormal Program
Termination 3-61, 3-62
AC voltage problem 3-50
Accelerator
battery below reference
voltage 3-39
battery not fully
charged 3-39
board in use 3-39
board not attached 3-39
board not detected 3-37
board permanently
disabled 3-38
board temporarily
disabled 3-38
cache 3-37
configuration
mismatch 3-39
data loss in cache 3-38
ECC errors 3-38
error log 3-37
obsolete data 3-38
obsolete data written to
drives 3-38
parity read 3-37
parity write 3-37
unrecognized status 3-38
valid data at reset 3-38
warranty alert 3-38
adapter/NVRAM ID
mismatch 3-39
ASR-2 detected by ROM 3-61,
3-62
ASR-2 Test Event 3-61, 3-62
automatic OS shutdown 3-50
Automatic Server Recovery
Base Memory Parity
Error 3-61
Extended Memory Parity
Error 3-61
Memory Parity Error 3-61
Reset Limit Reached 3-61
battery
below reference
voltage 3-39
not fully charged 3-39,
3-42
Battery Failing 3-61
Battery X not fully
charged 3-42
beeps only 3-20
board not attached 3-39
Caution, Temperature
Exceeded 3-62
configuration signature is
zero 3-39
configuration signature
mismatch 3-39
controller
communication failure 3-39
configured 3-40
firmware needs
upgrading 3-39
located in special video
slot 3-39
POST error 3-40
restarted with signature of
zero 3-40
Controller detected. NVRAM
configuration not
present 3-39
correctable error
threshold exceeded 3-49,
3-50
Diagnostic Error 3-62
dirty data 3-37
disable command issued 3-40










