User`s manual

MKP 2000 Remote Control Panel • SIS
™
Operation
MKP 2000 Remote Control Panel • SIS
™
Operation
SIS
™
Operation, cont’d
4-14 4-15
Command/response table for MKP SIS commands (continued) Command ASCII Command Response Additional description
(host to MKP) (MKP to host)
IP setup
Set MKP name
Esc
X15
CN Ipn
X15
Assign a name to the MKP.
Set MKP name to factory default
Esc
• CN Ipn•
X16
Reset the MKP’s name to the factory default.
Read MKP name
Esc
CN
X15
Read assigned MKP name (
X15
may be
X16
).
Set time/date
Esc
X17
CT Ipt
X
18
Set the time and date.
Read time/date
Esc
CT
X
18
Read the time and date.
Set GMT offset
Esc
X19
CZ Ipz
X19
The divider between hours and minutes is a period.
Read GMT offset
Esc
CZ
X19
Set Daylight Savings Time
Esc
,
X
20
CX Ipx
X
20
Set the switcher to display the local time as
Daylight Savings Time (+1 hour) in summer months.
Read Daylight Savings Time
Esc
CX
X
20
Set DHCP on or off
Esc
X1
DH Idh
X1
Read DHCP status
Esc
DH
X1
Set MKP IP address
Esc
X21
CI Ipi
X21
Read MKP IP address
Esc
CI
X21
Read hardware (MAC) address
Esc
CH
X22
Set subnet mask
Esc
X21
CS Ips
X21
Read subnet mask
Esc
CS
X21
Set gateway IP address
Esc
X21
CG Ipg
X21
Read gateway IP address
Esc
CG
X21
The set target IP parameters command can be issued with either the target IP address (
X21
) or the connection priority (
X23
) variable,
but not both. The response is as shown regardless of which variable is entered.
Command/response table for MKP SIS commands (continued) Command ASCII Command Response Additional description
(host to MKP) (MKP to host)
IP setup, continued
Set target (switcher) IP parameters
Esc
X21
— or —
X23
SI
Sip
X21
,
X22
,
X23
Read target (switcher) IP parameters
Esc
SI
X21
,
X22
,
X23
Set target (switcher) password
Esc
X24
PI Spw
X24
For the set target password command (
Esc
X24
PI ), the password variable
X24
can be either the administrator or the user password.
Clear target password
Esc
• PI Spw•
Read target password
Esc
PI ****
The retuned value for the read target password command (
Esc
PI ) is masked; the value is either empty (no return other than the )
if no switcher password is assigned, or four asterisks (****
) if a password is assigned.
Set MKP administrator password
Esc
X24
CA Ipa
X24
Clear MKP administrator password
Esc
• CA Ipa •
Read MKP administrator password
Esc
CA
X24
You must have an administrator password assigned before you can assign a user password. When you have connected multiple MKPs to control a switcher through a primary MKP control panel, do not set a user password on the primary MKP.
Set user password
Esc
X24
CU Ipu
X24
Clear user password
Esc
• CU Ipu •
Read user password
Esc
CU
X24
Switch Web page priority
Esc
X25
Cpag Iwp
X25
Read Web page priority
Esc
Cpag
X25
Set verbose mode
Esc
X1
CV Vrb
X1
Set MKP to report changes from other sources.
Read verbose mode
Esc
CV
X1
Read the verbose mode.
Read connection’s security level
Esc
CK
X10