Compaq ProLiant 1850R Setup and Installation Guide Second Edition (January 1999) Part Number 333172-002 Compaq Computer Corporation
Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
iii Contents About This Guide Text Conventions........................................................................................................................ xi Symbols in Text.........................................................................................................................xii Symbols on Equipment..............................................................................................................xii Rack Stability ....................................................
iv Compaq ProLiant 1850R Features continued Automatic Server Recovery-2 (ASR-2)...........................................................................1-20 Compaq Integrated Remote Console ...............................................................................1-21 Status LEDs.....................................................................................................................1-22 Security Features .....................................................................................
v Server Installation Overview continued Routine Maintenance ..............................................................................................................2-37 Optional Installation Service ..................................................................................................2-37 Chapter 3 Installing Hardware Options Accessing Non Hot-Plug Areas ................................................................................................
vi Chapter 4 Cabling Guidelines Connecting the Power Cord and Peripheral Devices ................................................................4-1 Rear Panel Connectors ......................................................................................................4-2 Internal Connectors ...........................................................................................................4-3 Cabling the Server’s Rear Panel Cables ................................................................
vii Server Configuration and Utilities continued Novell Device Drivers from Compaq..............................................................................5-11 Microsoft Windows NT Device Drivers from Compaq...................................................5-13 SCO OpenServer and SCO UnixWare Device Drivers from Compaq ............................5-15 IBM OS/2 Device Drivers from Compaq ........................................................................5-17 SunSolaris Device Drivers from Compaq .
viii Appendix B Electrostatic Discharge Grounding Methods ................................................................................................................. B-1 Appendix C Power Cord Set Requirements General Requirements ............................................................................................................. C-1 Country-Specific Requirements...............................................................................................
ix Appendix G Updating LAN Drivers Introduction ......................................................................................................................G-1 Installing NetWare Lan Drivers .......................................................................................G-1 LAN Driver Update Procedure For NetWare 3.2 .............................................................G-6 Installing IBM OS/2 LAN Drivers ..............................................................................
xi About This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and future upgrades. Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys appear in boldface. A plus sign (+) between two keys indicates that they should be pressed simultaneously. USER INPUT User input appears in a different typeface and in uppercase.
xii About This Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. ! WARNING: Indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Indicates that failure to follow directions could result in damage to equipment or loss of information. IMPORTANT: Presents clarifying information or specific instructions. NOTE: Presents commentary, sidelights, or interesting points of information.
xiii Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. Power Supplies or Systems marked with these symbols indicate the equipment is supplied by multiple sources of power.
xiv About This Guide Telephone Numbers For the name of your nearest Compaq Authorized Reseller: In the United States, call 1-800-345-1518 In Canada, call 1-800-263-5868 For Compaq technical support: In the United States and Canada, call 1-800-386-2172 For Compaq technical support phone numbers outside the United States and Canada, visit the Compaq Web Site at: //www.compaq.com Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: A-FRNT.
1-1 Chapter 1 Compaq ProLiant 1850R Features The Compaq ProLiant 1850R rack server offers state-of-the-art performance, full-featured functionality, and unsurpassed servicability in a new space saving design. This robust rack server supports configuration deployment flexibility, making it an unbeatable data center or remote site solution.
1-2 Compaq ProLiant 1850R Features Figure 1-2. Compaq ProLiant 1850R server with Wide Ultra2 SCSI Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: B-CH01.
1-3 ProLiant 1850R Front View ProLiant 1850R with Wide Ultra SCSI-3 The following figure shows the available bay configurations on the front of a server with Wide Ultra SCSI-3. The top view of figure 1-2 shows the three 1inch hot-plug drive configuration. The bottom view of figure 1-2 shows the two 1.6-inch hot-plug configuration. Either configuration is possible in ProLiant 1850R without any additional hardware. 1 2 3 4 5 B A B A 6 Figure 1-3.
1-4 Compaq ProLiant 1850R Features ProLiant 1850R Front Components Continued 5 0, 1, 2 Hot-Plug drive cage accommodating - Three (3) 1-inch height Compaq hot-plug hard drives 6 0, 1 Hot-Plug drive cage accommodating - Two (2) 1.6-inch height Compaq hot-plug hard drives ProLiant 1850R with Wide Ultra2 SCSI The following figure shows the available Wide Ultra2 bay configuration on the front of the server consisting of four 1-inch hot-plug drives. 1 3 2 1 0 2 B A Figure 1-4.
1-5 Table 1-2 Compaq ProLiant 1850R Wide Ultra2 Front Components Identifier Media Positions Configuration 1 0, 1, 2, 3 Hot-Plug drive cage accommodating - Four (4) 1-inch height Compaq hot-plug Wide Ultra2 SCSI hard drives 2 A and B two 5.
1-6 Compaq ProLiant 1850R Features Thumbscrew Identification The following figure shows the location of the thumbscrews used to secure the server to the rack and the thumbscrews used to attach the server cover. 2 1 2 1 2 Figure 1-5.
1-7 ProLiant 1850R Rear Components The following figure shows the components on the rear of the server. 11 1 2 3 4 5 6 7 8 9 10 Figure 1-6.
1-8 Compaq ProLiant 1850R Features Locating ProLiant 1850R Server Internal Components Inside View of the ProLiant 1850R Server The following illustration provides an inside view of the main features of the server. Table 1-5 designates key features. 8 7 6 5 4 3 2 10 1 9 Figure 1-7.
1-9 ProLiant 1850R Internal Components Continued 5 Intel Processor (CPU), Socket 2 (unpopulated) 6 Processor Power Module, Socket 1 7 Processor Power Module, Socket 2 (unpopulated) 8 Riser Board and Brace 9 3.5-inch 1.44-MB standard diskette drive 10 CD-ROM drive adapter board IMPORTANT: Heat sinks and processor guides are different for 500-Mhz processor. Industry Support Compaq delivers extensive testing and support for major server operating systems.
1-10 Compaq ProLiant 1850R Features ProLiant 1850R System Memory 100-MHz registered SDRAM (Synchronous DRAM) Error Checking and Correcting (ECC) memory uses an error encoding scheme for memory error detection and correction. Specifically, this feature detects and corrects for single-bit memory errors. Expandable to 1-GB of memory installed in dual inline memory module (DIMM) sockets. Memory can be expanded one module at a time.
1-11 4 3 2 1 Figure 1-9. Rear view of expansion slot locations Slot location 4 is a Shared PCI/ISA slot for access to either the PCI bus or the ISA bus. Slots 1, 2, and 3 are PCI slots for access to the 33-MHz PCI bus. They provide data transfer rates up to 133-Mb/s. The PCI bus provides peripheral transactions at a system clock speed of 33-MHz. Disk Controller The Dual Channel Integrated Wide-Ultra SCSI-3 controller utilizes two independent SCSI channels (Ports).
1-12 Compaq ProLiant 1850R Features For information about the SCSI hard drive installation, see chapter 3, “Installing Hardware Options.” For more information concerning the Dual Channel Integrated WideUltra SCSI-3 controller, see the System Reference Library (SRL) CDROM. Integrated Network Controller Autosensing LAN capable at either 10 or 100-Mb/s. Full duplex Ethernet for two way transmission. RJ-45 connector for 10-BaseT, or for 100TX Ethernet.
1-13 SCSI ID 2 SCSI ID 1 B SCSI ID 0 A SCSI ID 1 SCSI ID 0 B A Figure 1-10. ProLiant 1850R server drive positions for a Wide Ultra SCSI-3 model Table 1-6 Description of ProLiant 1850R Media Bays Identifier Media Positions Configuration A A 5.25-inch wide x half height drive bay (removable media area) B B 5.
1-14 Compaq ProLiant 1850R Features Mass Storage Wide Ultra2 SCSI Models The Compaq ProLiant 1850R server with the Wide Ultra2 SCSI drive cage can house up to 8 mass storage devices. Up to four 1-inch height or two 1.6-inch height Compaq hot-plug hard drives A low profile IDE CD-ROM drive A 3.5-inch, 1.44-MB diskette drive, installed in the vertical position Two available half-height 5.
1-15 Table 1-7 Description of ProLiant 1850R Wide Ultra2 Media Bays Identifier Media Positions Configuration 1 0, 1, 2, 3 Hot-Plug drive cage accommodating - Four (4) 1-inch height Compaq hot-plug Wide Ultra2 SCSI hard drives 2 A and B two 5.
1-16 Compaq ProLiant 1850R Features Video Integrated video controller provides maximum resolution of 1152 x 864 non-interlaced resolution at 256 colors. Supports SVGA, VGA, and EGA graphics resolution. 1-MB video memory ROM Software-upgradable firmware including diagnostics ROMPaq utility used to upgrade ROM Hot Plug Power Supply 225-watt hot-plug power supply Additional optional hot-plug redundant power supply providing 225-watts of redundant power or 400-watts of load-sharing power.
1-17 Server Management and Configuration Compaq offers an extensive set of features and optional tools to support effective server management and configuration.
1-18 Compaq ProLiant 1850R Features An information message indicating that you are running with a default configuration occurs each time you boot the system until you run the System Configuration program. Compaq SmartStart Compaq SmartStart, which is located on the Compaq SmartStart and Support Software CD, is the intelligent way to configure your Compaq server with major operating system software. SmartStart helps you achieve a well-integrated server that ensures maximum managability and dependability.
1-19 Fault Tolerance Fault Tolerance allows the server to recover from a hardware problem without interrupting the servers’s performance. SCSI Managed Array Technology (SMART) adds a controller to deliver the following functions: RAID 0 - no fault tolerance RAID 1 - mirroring RAID 4 - data guarding RAID 5 - distributed data guarding Fault tolerance for the ProLiant 1850R server is covered in the online documentation on the System Reference Library CD.
1-20 Compaq ProLiant 1850R Features Compaq System Configuration Utility The Compaq System Configuration Utility performs a wide range of configuration activities including: Configures PCI boards automatically Provides switch and jumper settings Resolves resource conflicts in areas such as memory, processor upgrades, and mass storage devices such as hard drives, tape drives, and diskette drives Sets and stores power-on features like date and time Stores configuration information of the operatin
1-21 Compaq Integrated Remote Console The standard Compaq Integrated Remote Console (IRC) performs a wide range of configuration activities. The IRC: Is accessible using ANSI terminal. Operates independently of the operating system. Provides for remote server reboot. Provides access to system configuration. Uses out-of-band communication with dedicated management modem installed in the server.
1-22 Compaq ProLiant 1850R Features Status LEDs There are three main groups of LEDs: One on each hot-plug power supply, two on the RJ-45 connector and a set of four on the front of the server. Additional LEDs include hard drives and the CD-ROM drive. Front Panel Status LEDs The set of LEDs on the front of the server indicate server status. The figure and table below identifies and describes the LEDs location and function. 4 3 2 1 Figure 1-12.
1-23 Front Panel Status LEDs Description Continued 3 Network Link Status (of integrated NIC) Green = Linked to Network, OFF = No Link 4 Network Activity Status (of integrated NIC) Green = Network Activity, OFF = No Activity Hot-Plug Power Supply LED The single LED indicator on each hot-plug power supply has two states: GREEN and OFF. The GREEN state indicates that power is connected to this supply and that the server is in the ON state.
1-24 Compaq ProLiant 1850R Features Diagnostics Some of the software and firmware diagnostics tools available for your use are: Power-ON Self-Test (POST) Diagnostics (DIAGS) ROMPaq utilities to upgrade flash ROMs Automatic Server Recovery (ASR-2) For information concerning Compaq diagnostic tools, refer to the Systems Reference Library CD included in the Reference Information pack of the shipping box.
2-1 Chapter 2 Server Installation Overview This chapter covers the following information about your new ProLiant 1850R server: Attaching the mounting hardware to the server and to the rack Installing the server into the rack Managing server cabling Accessing the internal components of the rack-mounted server You can choose the optional installation service from Compaq to install your rack products. See “Optional Installation Service” at the end of this chapter. Figure 2-1.
2-2 Server Installation Overview The Compaq Installing Rack Products CD is included with your server. The Rack Builder Configuration and Rack Information Library information can be found on the web on the Compaq website at www.compaq.com. The entire Rack Resource CD Kit, P/N 298721-001, ships with all Compaq racks and can be ordered through a Compaq authorized reseller.
2-3 Rack Warnings and Precautions Before beginning these procedures, make sure you understand the following warnings and caution: WARNING: To reduce the risk of personal injury, always ensure that the rack is adequately stabilized before extending a component outside the rack. A rack may become unstable if more than one component is extended for any reason. Extend only one component at a time.
2-4 Server Installation Overview WARNING: Before beginning to work on the rack, be sure that the leveling jacks are extended to the floor, that the full weight of the rack rests on the level floor, and that either stabilizers are installed or that multiple racks are coupled together for stability. Server Warnings and Precautions WARNING: To reduce the risk of personal injury from hot surfaces, allow the hot plug drives and the internal system components to cool before touching.
2-5 The Optimum Environment When installing your Compaq ProLiant 1850R server in a rack, certain standards of temperature and power requirements must be met. Space Requirements The following spatial needs should be considered when deciding where to install your rack: Clearance in the front of the rack should be a minimum of 25 inches for the front door to open all the way and for adequate airflow.
2-6 Server Installation Overview For electrical power ratings on options, refer to the product's rating label or user documentation supplied with that option. Grounding For proper operation and safety, this equipment is required to be properly grounded in accordance with NFPA 70-1993, Article 250. All power distribution devices, branch wiring, and receptacles must be "Listed" grounding type devices.
2-7 CAUTION: To reduce the risk of damage to the equipment when installing third-party options: Ensure that the option equipment does not impede airflow to the Rack-Mountable ProLiant Servers or increase the internal rack temperature beyond the Compaq specified maximum rating. Ensure that the Manufacturer’s Maximum Recommended Ambient Operating Temperature of the option equipment is not exceeded when installed in the rack.
2-8 Server Installation Overview Installation Sequence A brief summary of the steps to install your Compaq ProLiant 1850R server follows: Select an appropriate site for your rack. See the Rack Planning and Information Guide online document. This guide can be found on the Rack Information Library CD or the information can be downloaded from the Compaq website at www.compaq.com and provides site selection criteria. Unpack the server and rack mounting hardware.
2-9 Set the switches: These switches include: system board switches and SCSI ID settings, if changes are required. See to Chapter 3, “Installing Hardware Options.” Attach rack mounting hardware to the rack and to the server. Mount the server into the rack. Attach the cable management arm to the rack. Connect the cables: These cables include: keyboard, mouse, monitor, network, and power cables.
2-10 Server Installation Overview Unpacking the Rack Server Unpack the server box and locate the materials and documentation necessary to install your rack-mountable server. Locating Materials All of the equipment needed to install the ProLiant 1850R server into the Compaq rack is included with the rack or with the server. 1 2 3 4 5 6 7 Figure 2-2. Rack mounting hardware Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: C-CH02.
2-11 Contents of the rack model server box include Compaq ProLiant 1850R server Power cord Rack mounting hardware (numbers reference Figure 2-2) Rack Mounting Brackets (2) Slide Rail Assembly (2) Cable Management Arm Cable Management Arm Server Bracket Cable Management Arm Rack Bracket Template that can be used to mark the rack for proper attachment of the rack mounting brackets Bag of screws Clips (not shown) Hardware documentation and software packs inside the shipping box: Ref
2-12 Server Installation Overview Wide-Ultra SCSI controller boards Tape drives Remote Insight Board/PCI Hot-plug redundant power supply Installing Expansion Boards and Other Major Hardware Options See Chapter 3, “Installing Hardware Options,” for installing PCI and ISA expansion boards and other major hardware options. The following major hardware options are available for the ProLiant 1850R server and may be obtained from your local Compaq Reseller or Authorized Compaq Service Provider.
2-13 Preparing the Rack Mounting Brackets and Slide Rail Assemblies Each pair of rack mounting brackets supports one rack-mountable server. Figure 2-3. Rack mounting brackets (2); alignment tabs identify front flanges Slide Rail Assembly Components Each slide rail assembly, illustrated below, attaches to the server and to the Rack mouning bracket. The components of the Slide Rail Assembly include the Outer Bracket Rail which includes the Outer Bracket Rail and the Inner Slide .
2-14 Server Installation Overview IMPORTANT: To make installing the rack mounting bracket easier, attach the outer bracket rail to the rack mounting bracket before attaching the rack mounting bracket assembly to the rack. This way, the joined mounting bracket and bracket rail can be fastened to the rack as one assembly. Attaching the Outer Bracket Rail to the Rack Mounting Bracket 1. Lay the slide rail assemblies (2), rack mounting brackets (2) and 1/4-inch fasteners (4) on a flat surface. 2.
2-15 The next figure shows the outer bracket rail with the inner slide and the server rail. Figure 2-6. Separated outer bracket rail (top) and server rail The outer bracket rail consists of a fixed outer rail that attaches to the rack mounting bracket, and an inner slide on a steel ball-bearing movement. This inner slide does not detach.
2-16 Server Installation Overview To identify the fronts of the rack mounting bracket and the outer bracket rail see the figure below: The front of the rack mounting bracket has alignment tabs on its flange and the round threaded holes . The front of the outer bracket rail allows the inner slide to move forward on ball bearings and can be identified by the plastic guides. 1 2 Figure 2-7.
2-17 Again, the front of the rack mount bracket can be identified by the round threaded holes; the rear of the rack mount bracket has oval holes. Figure 2-8. Positioning the rack mounting bracket for installation of the outer bracket rail 5. Lay the outer bracket rails inside the rack mounting brackets along the inside edge of the rack mounting bracket. The front of both pieces (rack mount bracket and outer bracket rails) should be oriented in the same direction.
2-18 Server Installation Overview 6. Fully extend the inner slides from the front of each outer bracket rail . With these pieces extended, a screw hole towards the rear, aligns in the rack mounting bracket and the outer bracket rail for each assembly. 7. Fasten the outer bracket rail to the rack mounting bracket with a 8-32 x 1/4-inch slotted screw. Do not tighten screws until all three screws have been lined up on each assembly. (Do not use nuts or washers with the screw.
2-19 2 1 4 3 6 5 Figure 2-9. Attaching outer bracket rail to rack mounting bracket 11. Tighten the three 8-32 x 1/4-inch slotted screws used to fasten the outer bracket rail to the rack mounting bracket. When the three screws are fastened, the rack mounting bracket and outer bracket rail form a rack mounting bracket slide assembly that you attach to the rack. In total, you use six screws, three for each assembly.
2-20 Server Installation Overview Attaching the Rack Mounting Bracket and Slide Assembly to the Rack WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that the rack leveling feet are extended to the floor and support the full weight of the rack. Each rack must be level and stable. Racks that are not coupled together require the installation of stabilizers. This must be done before you perform any work on the rack.
2-21 2. When you mark the positioning of the mounting bracket screws, also mark the positioning for the cage nuts. These are two slots marked "C" on the template. The cage nuts on the front hold the thumbscrews through the server's front bezel, as shown in the following figure. The cage nuts on the back allow fastening of the rack mounting slide assembly to the vertical rails.
2-22 Server Installation Overview 1. Position the cage nut as shown in the following figure, on the inside of the rail. 2. Hook one of the lips of the cage nut through the square rail perforation. 3. Insert the tip of the fitting tool through the other side of the perforation and hook the opposite lip of the cage nut. Figure 2-11. Inserting cage nuts 4. Using the fitting tool as a lever, pry the cage nut into position. 5. Repeat for each cage nut.
2-23 Figure 2-12. Attaching rack mounting bracket assembly to the front of the rack (left side) IMPORTANT: Only insert one screw in the front of the bracket and position it in the bottom hole. IMPORTANT: The screw holes on the front of the bracket are round and threaded. Figure 2-13. Attaching rack mounting bracket assembly to the front of the rack (right side) 2. Carefully align the mounting bracket assembly with the rear rack frame.
2-24 Server Installation Overview 3. Secure the back end of the mounting bracket assembly to the back corner brace of the rack with one M6 x 1.0-12L Phillips screw through the bottom hole of the bracket and the cage nut, as shown in the following figure. Figure 2-14. Attaching the back of mounting bracket assembly to the rack (left view) IMPORTANT: The screw holes on rear of the brackets are oval holes. Figure 2-15. Attaching the back of mounting bracket assembly to the rack (right view) 4.
2-25 Attaching Server Rails to the Server 1. Place the center tab on the server rail with the open end of the tab towards the front of the server. IMPORTANT: The server rails attach to the server with the flat side of the rail towards the server. The holes in the server rail will line up only one way with the chassis. 2. Attach the flat side of a component rail to each side of the server chassis with three 8-32 x 1/4-inch Phillips screws. Do not use washers with the screws. Figure 2-16.
2-26 Server Installation Overview Figure 2-17. Attaching the server bracket to the server Loading the Rack Server Follow the steps below to load and secure the server to the rack with the front bezel thumbscrews before attaching additional mounting bracket assemblies. Ensure that this pair of brackets is perfectly aligned and installed and that the server fits before you continue.
2-27 3. Press the server rail release latch on either side of the server and slide the server into the rack. Figure 2-18. Loading the rack server IMPORTANT: The first time you slide the server into the rack, you may have to apply some pressure. After the first time, the ball bearings in the slide will move easily. IMPORTANT: When servicing the server, fully extend the server until the latches lock. To return the server to the rack, depress the latches and slide the server into the rack. 4.
2-28 Server Installation Overview Figure 2-19. Using thumbscrews to secure the positioned server in the rack 5. Tighten the thumbscrews before you close the rack door to prevent the door from hitting protruding thumbscrews. Attaching the Cable Management Arm A double-hinged cable management arm with fasteners ship with each server. The cable management arm attaches to the server's cable management arm bracket and to the rear frame of the rack. All cables to and from the server are tied to this arm.
2-29 Figure 2-20. Attaching the cable management arm to the cable management arm server bracketG 2. The cable management arm attaches to the rack via the cable management arm rack bracket. Align the cable management arm rack bracket to the left side on the rack. Position the rack bracket one hole above the rack mount bracket as shown below. When the rack bracket is in place secure it with two 10-32 x 5/8-inch Phillips washer-face hexhead screws. Figure 2-21.
2-30 Server Installation Overview 3. Align the other end of the cable management arm on the outside of the rack bracket attached to the rack. Attach the arm to the rack bracket with two 10-32 x 5/8-inch Phillips washer-face hex-head screws. Figure 2-22. Attaching the cable management arm to the cable management arm rack bracket Connecting the Power Cord and Peripheral Devices You are now ready to connect the power cord and peripheral devices to the connectors located on the rear panel of the server.
2-31 11 1 2 3 4 5 6 7 8 9 10 Figure 2-23. Rear panel of ProLiant 1850R Table 2-2 Rear Panel Connectors/LED Ref.
2-32 Server Installation Overview 1. Plug cables into the server. Figure 2-24. Cabling through the cable management arm and cable support 2. Plug the power cord (s) into the server. Make a small loop in each power supply cable and secure the loop as a strain relief to the location below the power supply. This prevents accidental removal of power cords when the server slides in and out of the rack. Figure 2-25. Securing the power supply power cord cable 3.
2-33 Figure 2-26. Securing cables to the cable management arm 4. Extend the bundled cables down the rack’s cable channel. Before loading additional components, be sure the server is secured to the rack using the front bezel thumbscrews. Powering Up the Server After the cables have been connected to the server, you are ready to power on the server. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug.
2-34 Server Installation Overview To power on the server press the ON/STANDBY power switch. Figure 2-27. Turning on power to server The server is now ready to be configured with the SmartStart and Support Software CD. Configuring the Server with Compaq SmartStart Compaq SmartStart is the intelligent way to configure the server and to load the system software, thereby achieving a well-integrated server to ensure maximum dependability and supportability.
2-35 Sets and stores power-on features like date and time Stores configuration information in nonvolatile memory Assists in the installation of the operating system Assists in running diagnostic tools such as TEST and INSPECT utilities The first time the server is configured, the SmartStart program automatically creates a system partition and installs the configuration utility and other Compaq utilities in that partition. To install the Compaq SmartStart and Support Software CD: 1.
2-36 Server Installation Overview Using the Power Switch The server is shipped from the factory with the power switch security feature in the unlocked position. In order to protect the server from accidentally being shut down due to accidental contact with the power switch, the switch protection can be enabled. Refer to Chapter 3, “Installing Hardware Options” for instructions on enabling the Power Switch Security Feature. Figure 2-29.
2-37 Registering Your Server You can register your server during the “Product Interviews” stage of the SmartStart configuration process. Refer to the Server Setup and Management pack included in the shipping box. Routine Maintenance For information concerning routine maintenance and safety precautions, refer to the Systems Reference Library CD included in the Reference Information pack of the shipping box.
3-1 Chapter 3 Installing Hardware Options This chapter is divided into two major parts: Accessing Removable Media (Non Hot-Plug) Areas - you must shut down the server power to install options, upgrades or replacements in the following areas: Processor sockets Memory sockets System board Expansion boards Rise board and riser board brace Installing Removable media devices Installing Wide Ultra2 SCSI drives Accessing Hot-Plug Areas - you can install hot-plug options, upgrades or replaceme
3-2 Installing Hardware Options Accessing Non Hot-Plug Areas To install options, upgrades, or replacements in these areas, you must first shut down the server power. Accessing Processors, Memory Sockets, and System Board WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching. CAUTION: Electrostatic discharge can damage electronic components. Be sure you are properly grounded before beginning any installation procedure. 1.
3-3 1 1 Figure 3-1. 5. Thumbscrew locations Pull the server out from the rack. IMPORTANT: It is not necessary to completely remove the server from the rack. Compaq ProLiant 1850R Setup and Installation Guide Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: D-CH03.
3-4 Installing Hardware Options 6. Loosen the three thumbscrews on the front of the unit which secure the server cover. 7. Slide the server cover toward the rear of the unit about 1 inch (2.5 cm), then remove the cover. Figure 3-2. Removing the server cover Installing a Processor and Processor Power Module To install a processor on the System Board, refer to the label inside the server cover, refer to the processor option kit, or follow the procedures below.
3-5 2 1 4 3 Figure 3-3. Processor and processor power module slot locations Table 3-1 Processor and Processor Power Module slot locations Identifier Description 1 Processor Power Module Slot 1 (populated) 2 Processor Slot 1 (populated) 3 Processor Power Module Slot 2 4 Processor Slot 2 WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching. CAUTION: Processor slot 1 must be populated at all times.
3-6 Installing Hardware Options 1. To install the processor, press it into the socket. Figure 3-4. Sliding the processor into the processor socket (riser board removed for clarity) 2. Push the processor latches outward until the processor latches snap into place. Figure 3-5. Locking the processor into the processor socket (riser board removed for clarity) IMPORTANT: The retention mechanism for securing the heatsink is different for the 500-MHz processor.
3-7 Installing a Processor Power Module Every processor supplied by Compaq comes with a Processor Power Module (DC-to-DC converter). Each Processor Power Module (PPM) must be installed in the slot adjacent to its processor to provide power to that processor. If the processor is installed in slot 1, install the PPM in slot 1, if the processor is installed in slot 2 install the PPM in slot 2. The Processor Power Module is keyed to ensure correct alignment.
3-8 Installing Hardware Options 4. Press the module into the socket while pushing the latches inward until the latches snap into place . 5. Replace the server cover. 6. Push the server into the rack, secure with thumbscrews and reconnect cables. 7. Power on server and use the System Configuration Utility to reconfigure your system. Adding Memory to the ProLiant 1850R Server You can expand server memory by installing Compaq DIMMs (Dual Inline Memory Modules).
3-9 CAUTION: Use only Compaq DIMMs. DIMMs from other sources are known to adversely affect data integrity. 4 3 2 1 Figure 3-7. DIMM Sockets identified on system board Table 3-3 DIMM Socket Identification Identifier Description 1 DIMM Socket 1 populated with standard 64-MB DIMM 2 DIMM Socket 2 3 DIMM Socket 3 4 DIMM Socket 4 Maximum Memory Configuration The ProLiant 1850R server allows ultimate expansion to 1-GB.
3-10 Installing Hardware Options Installing DIMMs CAUTION: Electrostatic discharge can damage electronic components. Be sure you are properly grounded before beginning any installation procedure. See Appendix B, “Electrostatic Discharge,” for more information. To install a memory module, complete the following steps: 1. Align the key slot in the bottom edge of each DIMM with the tab in the expansion slot. DIMMs will not seat if turned the wrong way. 2 1 2 Figure 3-8.
3-11 Shared PCI/ISA Slot 4 3 2 1 PCI Slots Figure 3-9. ProLiant 1850R riser board slots Expansion boards can be installed in the following slots. 4 3 2 1 Figure 3-10. Locating ProLiant 1850R four (4) expansion slots Compaq ProLiant 1850R Setup and Installation Guide Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: D-CH03.
3-12 Installing Hardware Options Installing an Expansion Board To install an expansion board, refer to the following installation Procedure. WARNING: To reduce the risk of personal injury, be careful when installing and removing expansion boards. The cover retaining clasps can pinch or cut your fingers. Do not attempt to force boards in or out of position. 1. If the server is on, shut down the operating system, place it in Standby and disconnect the power cord (s).
3-13 3 Figure 3-12. Removing slot cover 6. Insert the expansion board . 7. Close the expansion slot latch to secure the board . IMPORTANT: When you install a board, make sure you press firmly on the board so that the entire connector seats properly in the riser board slot. 5 4 Figure 3-13. Inserting an expansion board NOTE: Some full length PCI Boards include a plastic adapter to allow full retention in some shared slots.
3-14 Installing Hardware Options Removing Expansion Board Shipping Bracket Some models of the ProLant 1850R include a bracket to keep expansion boards in place during shipping. You must remove this bracket before installing or removing expansion boards, however reinstalling the bracket is optional. Figure 3-14.
3-15 3. Remove all expansion boards by reversing the steps in the “Installing an Expansion Board” procedure. 4. Loosen the two captive screws securing the riser board brace. 5. Lift the riser board and riser board brace out of the server as shown below. 2 1 Figure 3-15. Removing the riser board and riser board brace 6. Install the new riser board and riser board brace assembly. When installing this assembly, refer to figure 3-15 for proper alignment. 1 2 Figure 3-16.
3-16 Installing Hardware Options 8. Replace the server cover. 9. Slide the ProLiant 1850 R server into the rack and secure using the thumbscrews. 10. Reconnect all cabling and turn the server on. 11. Reconfigure the server. See to Chapter 5, “Server Configuration and Utilities.” Installing Removable Media Devices Refer to the General Installation Guidelines below for general rules regarding drive installation.
3-17 SCSI ID Settings for Compaq Hard Drives The following chart provides the SCSI ID jumper settings for Compaq SCSI hard drives. Table 3-4 SCSI ID Settings SCSI ID 6 5 4 3 2 1 0 Bit 2 Bit 1 Bit 0 ON ON ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF ON OFF Installing ProLiant 1850R Mass Storage Devices There are three or four drive bays for internal mass storage devices in the ProLiant 1850R server.
3-18 Installing Hardware Options B A Figure 3-17. Optional mass storage device placement for ProLiant 1850R with Wide Ultra SCSI-3 model 3 2 1 0 B A Figure 3-18. Optional mass storage device placement for ProLiant 1850R with Wide Ultra2 SCSI model IMPORTANT: A 2 by 1-inch Wide Ultra2 SCSI drive cage option is available to go with the hot-plug hard drives in the removable media area.
3-19 Replacing the 1.44-MB Diskette Drive (Floppy Drive) Removing the 1.44-MB Diskette Drive (floppy drive) 1. If the server is on, place it in Standby and disconnect the power cord (s). Refer to Chapter 2, “Server Installation Overview.” 2. Pull the server forward in the rack to access the inside of the server. 3. Remove the server cover. 4. Disconnect the cabling to the 1.44-MB diskette drive. Figure 3-19. Disconnecting the 1.44-MB diskette drive cabling 5.
3-20 Installing Hardware Options 1 2 Figure 3-20. Releasing the diskette drive 6. Rotate the rear of the drive towards the outside of the chassis . 7. Lift the diskette drive straight up to remove it . CAUTION: When removing or installing the diskette drive be careful not damage the eject button on the front of the diskette drive. 4 Front View Figure 3-21. 3 Releasing the 1.
3-21 Installing the 1.44-MB Diskette Drive (Floppy Drive) To install the 1.44-MB diskette drive into the server, reverse the steps noted in the proceeding procedure. Enabling the Power Switch Security Feature When the power switch security feature is enabled it protects the server from being shut down due to unintentional contact with the power switch. In the enabled mode you must use a slender rod (such as the eraser end of a pencil) to depress the center circle of the power switch.
3-22 Installing Hardware Options 2 1 Figure 3-22. Removing the power switch from the front bezel (power switch cabling removed for clarity) 6. Rotate the switch assembly 180 degrees ➊. 7. Insert the switch into the front bezel as shown below ➋. Make sure that you include the spring, the clips on the switch engage, and the center post of the switch aligns with the hole in the bezel. 1 2 Figure 3-23. Inserting the power switch into the front bezel 8. Replace the 1.
3-23 Replacing the CD-ROM Drive The following procedure discusses removing and installing the CD-ROM drive. Removing the CD-ROM Drive 1. If the server is on, place it in Standby and disconnect the power cord-(s). See to Chapter 2, “Server Installation Overview”. 2. Pull the server forward in the rack for access to the inside of the server. 3. Remove the server cover. 4. Remove the 1.44-MB diskette drive (floppy drive) to access the screw which secures the CD-ROM drive.
3-24 Installing Hardware Options Figure 3-25. Installing the CD-ROM from the chassis Attaching Mass Storage Devices Bays A and B can accomodate two half-height or one full height device(s). Devices that can be installed include: an additional CD-ROM drive, 1-inch or 1.6-inch height hard drives, SLR, DAT, or DLT tape drives.
3-25 4. Remove the 1.44-MB diskette drive (floppy drive) to access the screw which secures the removable media tray. See the “Replacing the 1.44-MB Diskette Drive” procedure above for details. 5. Remove the screw that secures the CD-ROM tray assembly to the chassis. Slide the CD-ROM tray forward out of the server. The CD-ROM tray and the CD-ROM drive adapter board disconnect. CD-ROM cabling remains attached to the CD-ROM adapter board. 6.
3-26 Installing Hardware Options Figure 3-27. Attaching a 3.5-inch drive to a 5.25-inch bracket 9. Install the bracket and drive into the drive bay. Make sure the guide screw lines up with the guide slot in the removable media drive cage. Secure the bracket with one screw through the right side of the drive cage. Figure 3-28. Installing and securing the drive into the chassis 10. Connect the cables (drive power and signal).
3-27 Figure 3-29. Connecting the drive cables 11. Replace the 1.44-MB diskette drive (floppy drive). 12. Replace the server cover. 13. Push the server into the rack and secure it. 14. Reconnect the power cord and power on the server. 15. Reconfigure the server. See to Chapter 5, “Using the System Configuration Utility,” for more information. Installing a Half-Height Device To install a half-height removable media device into the removable media bay area follow the steps below. 1.
3-28 Installing Hardware Options Figure 3-30. Installing a half-height device 3. Connect the two device terminated SCSI cable to the half-height device. IMPORTANT: If the device is a Fast-SCSI-2 device, install a 68 to 50 pin adapter and connect to the device before connecting the cable. Figure 3-31. Cabling a half height drive to the port 2 with the two device terminated cable 4. Replace the 1.44-MB diskette drive (floppy drive). 5. Replace the server cover.
3-29 6. Push the server into the rack and secure it. 7. Reconnect the power cord and power on the server. 8. Reconfigure the server. See to Chapter 5, “Using the System Configuration Utility,” for more information. Installing a Full-Height Device (DLT Tape Drive) To install a full-height device into the removable media bay area: 1. Remove both removable media trays in bay areas A and B. See the “Installing a 3.5-inch Drive into a 5.25-inch Drive Bay” procedure above and follow steps 1 through 6. 2.
3-30 Installing Hardware Options Figure 3-33. Installing a DLT tape drive into the removable media cage 4. Connect the two device terminated cable to the DLT. Figure 3-34. Cabling a DLT tape drive to port 2 with the two device terminated cable 5. Replace the diskette drive (floppy drive). 6. Replace the server cover. 7. Push the server into the rack and secure it. 8. Reconnect the power cord and power on the server.
3-31 9. Reconfigure the server. See Chapter 5, “Using the System Configuration Utility,” for more information. Accessing the Hot-Plug Areas This section describes accessing the following areas: Hot-Plug SCSI Wide Ultra SCSI-3 Drives Hot-Plug SCSI Wide Ultra2 SCSI Drives Hot-Plug Power Supplies Installing Hot-Plug Wide Ultra SCSI-3 Drives 1. Remove the blank (s) from the hot-plug hard drive cage. 2. Insert the hot-plug drive . 3. Close the connector levers . 2 1 Figure 3-35.
3-32 Installing Hardware Options Installing Hot-Plug Wide Ultra2 SCSI Drives 1. Remove the blank (s) from the hot-plug hard drive cage. 2. Insert the hot-plug drive . 3. Close the connector levers . 1 2 Figure 3-36. Installing a Wide Ultra2 SCSI drive NOTE: place.
3-33 SCSI ID 2 SCSI ID 1 B SCSI ID 0 A SCSI ID 1 B SCSI ID 0 A Figure 3-37. SCSI ID and removable media numbers for Wide Ultra SCSI-3 models SCSI ID Numbers for Wide Ultra2 SCSI Models The Wide Ultra2 SCSI model configuration consists of four 1-inch height hotplug drives numbered SCSI ID 0, 1, 2, and 3. The removable media bays can be removed to accommodate two additional hot-plug drives with SCSI ID 4 and 5. 3 2 1 0 B A Figure 3-38.
3-34 Installing Hardware Options Installing a Hot-Plug Redundant Power Supply 1. Open the rear door of the rack to access the back of the server. 2. Open the lever on the cable management arm and swing the arm out of the way. 1 2 Figure 3-39. Accessing the hot-plug power supplies 3. Remove hot-plug power supply blank. NOTE: The procedure for adding a hot-plug redundant power supply and replacing a power supply are virtually identical.
3-35 3 1 2 Figure 3-40. Removing the hot-plug power supply blank (or power supply) 4. Open the power supply latch on the new supply by pressing the thumbscrew release and open the latch. Install the new hot-plug power supply in your open area. Push the hot-plug power supply into the slot and swing the arm into the locking position and it locks in place. 1 2 Figure 3-41. Installing a hot-plug power supply 5. Plug the power cord into the new hot-plug power supply.
3-36 Installing Hardware Options Figure 3-42. 6. Plugging in the power cord Secure the power supply cord by fastening it to the clamp on the power supply and attach to the cable management arm. Figure 3-43. Securing the power cord 7. Swing the cable management arm back into place and secure the latch . Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: D-CH03.
3-37 2 1 Figure 3-44. Securing the cable management arm 8. Close the rear rack door. Compaq ProLiant 1850R Setup and Installation Guide Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: D-CH03.
4-1 Chapter 4 Cabling Guidelines This chapter is intended to help you set up your server and drive cage option(s) for optimal performance. Use this chapter along with the technical information on the Quick Hardware Installation Poster and the labels found on the inside of the server cover for complete and comprehensive information.This chapter also identifies the cables you use and how to connect them.
4-2 Cabling Guidelines Rear Panel Connectors The illustration below shows the connectors and switches for the ProLiant 1850R server. 11 1 2 3 4 5 6 7 8 9 10 Figure 4-1. Location of rear panel connectors Table 4-1 Rear Panel Connectors Ref.
4-3 Internal Connectors The main connectors are the two SCSI Ports (i.e. Port 1 and Port 2), the diskette drive connector and the IDE connector. They are labeled in the table below. CAUTION: Do not run internal and external devices off the same SCSI channel (port). When running external storage boxes, you should disconnect the internal cable from Port 2.
4-4 Cabling Guidelines Table 4-2 Important Connectors Ref. Connector 1 Floppy Connector 2 Port 2 SCSI Connector (2), It connects to the removable media bay for SCSI hard drives, tape drives, or external SCSI devices via the external connector. 3 IDE Connector 4 Port 1 SCSI Connector, It connects to the Hot-Plug Drive Cage. Cabling the Server’s Rear Panel Cables You are now ready to connect the power cord and peripheral devices to the connectors located on the rear panel of the server.
4-5 2. Plug in the power supply cables and secure. Figure 4-4. Securing the hot-plug power supply cables 3. Bundle all of the cables, including the power cable (s), and tie them to the cable management arm. Figure 4-5. Cabling the server rear panel cables Compaq ProLiant 1850R Setup and Installation Guide Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: E-ch04.
4-6 Cabling Guidelines Additional Mass Storage Devices Removable media bays for ProLiant 1850R servers The Compaq ProLiant 1850R server can house up to 2 non hot-plug hard drives or various other devices in the removable media bays. Two half height removable media bays, can support the following removable media devices: 1.6-inch or 1-inch form factor non hot-plug drive DAT or SLR half-height tape drive DLT full height tape drive Additional 1.
4-7 SCSI Hard Drive Installation Guidelines The following guidelines should be noted when adding SCSI hard drives: A maximum of seven SCSI devices per port can be added. Each SCSI drive must have a unique ID. Compaq SCSI cables for the ProLiant 1850R server are terminated. Be sure to remove all terminating jumpers from third-party SCSI devices. Supported Compaq SCSI options are not terminated.
4-8 Cabling Guidelines ProLiant 1850R Server Cable Kit Contents All cabling for ProLiant 1850R models is illustrated below. Verify that you have all of the necessary items before beginning the installation process. 1 2 3 4 Figure 4-6. ProLiant 1850R server cabling components Using the following table and figure 4-6 verify that you have the four cables shipped with your server.
4-9 Table 4-3 ProLiant 1850R Server Cables and Server Cable Kit Contents Indicator Number Description Part Number/Location 1 Two device terminated SCSI cable (1). 296016-004, in server 2 Floppy drive cable (1). 171886-005, in server 3 IDE cable (1) for the CD-ROM drive. 242947-009, in server 4 Point-to-Point SCSI cable (1) for the Hot-Plug Hard Drive cage.
4-10 Cabling Guidelines SCSI Cable Connectors To help identify the SCSI cables required for ProLiant 1850R server installation, refer to the illustrations below. Keep in mind these characteristics of SCSI cables: External SCSI cables have a round wire with securable connectors. Internal SCSI cables have a flat ribbon wire with push-on connectors. Compaq SCSI cables are keyed so they cannot be installed incorrectly.
4-11 SCSI Cabling Guidelines Determining the Cables you Need The following guidelines are provided as an overview for first-time cable connections and installation in the ProLiant 1850R server. Only controllers listed in the tables below are supported by the ProLiant 1850R server. Refer to these tables to determine the parts that are necessary for successful cabling solutions for the ProLiant 1850R.
4-12 Cabling Guidelines Internal SCSI Cabling Guide For Compaq ProLiant 1850R Servers The ProLiant 1850R server includes the following components to be used in cabling the server: One IDE cable for IDE CD-ROM drive One floppy drive cable One two device terminated SCSI cable One point-to-point SCSI cable Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: E-ch04.
4-13 Internal Cabling Table 4-4 Internal Cabling for the Compaq ProLiant 1850R Compaq ProLiant 1850R Wide-Ultra SCSI-3 Fast SCSI-2 Non Hot- 4/8 DAT Drive, 4/8 SLR Wide Ultra2 SCSI Hotand Fast-Wide SCSIPlug Drive, 12/24 DAT Drive, Plug Hard Drives 2 Hot-Plug Hard Hard Drives 15/30 DLT Drive, Drives 20/40GB DLT Drive, 35/70 DLT Drive, and SCSI CD-ROM Drive Dual Channel Wide-Ultra SCSI-3 Controller (Integrated) SCSI Port 1 or 2 No additional cables required.
4-14 Cabling Guidelines Internal Cabling for the Compaq ProLiant 1850R Continued Compaq ProLiant 1850R Wide-Ultra SCSI-3 and Fast-Wide SCSI-2 Hot-Plug Hard Drives Fast SCSI-2 Non Hot-Plug Hard Drives 4/8 DAT Drive, 4/8 SLR Drive, 12/24 DAT Drive, 15/30 DLT Drive, 20/40GB DLT Drive, 35/70 DLT Drive, and SCSI CD-ROM Drive SMART-2SL Array Controller No additional cables required. Connect the Wide SCSI pt to pt cable, P/N 296016-003, from the controller to the hot plug back plane.
4-15 External Cabling for Primary Storage Only Table 4-5 External Cabling for Primary Storage Only Compaq ProLiant 1850R ProLiant Storage System ProLiant Storage System Model U1 ProLiant Storage System Model U2 Compaq Wide-Ultra SCSI Controller (PCI) SMART-2SL Array Controller SMART-2/P Array Controller, SMART-2DH Array Controller No additional cables required. Controllers include an external 12’ Wide to Wide SCSI cable. Dual bus models include two external cables.
4-16 Cabling Guidelines External Cabling for Secondary Storage Table 4-6 External Cabling for Secondary Storage All ProLiant 1850R Models 4/8 DAT Drive, 4/8 SLR Drive, 12/24 DAT Drive, 20/40GB DLT Drive, and SCSI CD-ROM Drive The SCSI Storage Expander Option Kit or Compaq Wide-Ultra Tape Drive Option Kit SCSI-3 Controller Card includes the external (PCI) cable required for this configuration.
4-17 ProLiant 1850R Cabling Examples The following examples illustrate cabling scenarios associated with a ProLiant 1850R server. They are provided as only an overview for installing and routing some of the cabling scenarios described in the SCSI Cable Usage Matrix. You may also want to refer to the hood labels attached to the inside of the server cover. If you have any problems, contact your local Compaq Authorized Reseller or Service Provider.
4-18 Cabling Guidelines Cabling a DLT Tape Drive to SCSI Port 2 Figure 4-9. Cabling a DLT tape drive to the port 2 Cabling a Half-Height Tape Drive SCSI Port 2 Figure 4-10. Cabling a half height tape drive to the port 2 Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: E-ch04.
4-19 ProLiant 1850R Maximum External Storage Cabling Connecting Three Array Controllers For Maximum External Storage Capability Cable one point-to-point cable to cable from the hot-plug drive cage to the first array controller. For the second array controller cable to the rear external SCSI access. Then for the third array controller cable it to either the second external SCSI access or to the open expansion slot (slot 1). Figure 4-11.
5-1 Chapter 5 Server Configuration and Utilities This chapter discusses many configuration options including, how to use the Compaq System Configuration Utility and Compaq SmartStart, and how to load device drivers.
5-2 Server Configuration and Utilities The System Configuration Utility uses option configuration (.CFG) files to set up and configure the computer. The .CFG files provide information such as switch settings, IRQs, and software installation guidelines. The .CFG files for Compaq servers is located on the System Configuration diskettes and Compaq SmartStart and Support Software CD (SmartStart and Support Software CD).
5-3 Starting the System Configuration Utility The first time you start the Compaq System Configuration Utility, follow the procedure on the Compaq SmartStart Installation poster. After the Compaq SmartStart and Support Software CD is used for the first time to create and populate the Compaq system partition, you may access the System Configuration Utility as follows: 1. Press the Ctrl+Alt+Del keys to reboot the server. 2.
5-4 Server Configuration and Utilities Operating System Installation - Allows you to install one of the operating systems listed or to specify installation of an operating system that is not listed. Diagnostics and Utilities - Tests and inspects the computer. Exit from this Utility - Restarts the computer.
5-5 Most ISA Plug and Play boards allow the board to be set to one of two modes. The modes are most commonly referred to as “Plug and Play” and “Legacy” mode. If a board is set to “Legacy" mode, usually through a jumper setting on the board, or through configuration software that ships with the board, then the board is treated as though it was a normal ISA board.
5-6 Server Configuration and Utilities Setting Power-On Defaults You can set and change the Power-On features at any time. 1. Select System Configuration from the Main Menu; then select Power-On Defaults. 2. Set the current date in the format: MM-DD-YYYY 3. Set the correct time in the format: HH:MM:SS 4. Set the Power-On Num Lock state: ( ) OFF (*) ON * This activates the numeric keypad when the computer is turned ON.
5-7 1. Insert the Compaq SmartStart and Support Software CD in the CD-ROM drive and turn on the server. IMPORTANT: The system partition requires about 32 MB of disk space at the beginning of the hard drive and an unused entry in the boot record. 2. Select Create/Update System Partition. This process takes three reboots. Verifying the System Partition To verify that the system partition exists, follow this procedure: 1. Remove any media from the CD-ROM drive and the diskette drive. 2.
5-8 Server Configuration and Utilities Configuration Backup The Configuration Backup option allows you to create a backup of the system configuration and to restore the system configuration from the backup. The following menu options are available: Backup Restore Configuration Backup and Configuration History Files When you save and exit the System Configuration Utility, the utility keeps a history of the configuration.
5-9 System Configuration History Log Files Continued SYSTEM.CHL Textual representation of SYSTEM.SCI file SYSTEM1.CHL Textual representation of SYSTEM1.SCI file SYSTEM2.CHL Textual representation of SYSTEM2.SCI file (oldest) IMPORTANT: If there is not enough disk space for the entire System Configuration History Log, the utility deletes log files starting with the oldest files (SYSTEM2.SCI and SYSTEM2.CHL) until enough disk space is available for the current configuration backup and history files.
5-10 Server Configuration and Utilities SCO OpenServer 5 SCO UnixWare 7 SCO UnixWare 2.1.x IBM OS/2 Warp Server 4.0 and Warp Server Advanced 4.0 IBM OS/2 Warp 4.0 IBM OS/2 Warp Connect 3.0 Banyan VINES v 6.x, 7.x, and 8.x SunSoft Solaris 2.5.1, 2.6 and above SMP Operating System Support Compaq provides optimized software support for the Dual Processing Boards for: Microsoft Windows NT servers 3.51 and 4.0, 4.0 Enterprise intraNetWare 4.
5-11 Not all operating systems ship with each server. Consult your local reseller or Compaq Customer Service if you need a Compaq SmartStart pack with additional operating system support. Some operating systems have driver support/updates but not an integrated Compaq SmartStart installation. You can still configure your server and manually install your operating system. Some operating systems have an integrated installation using the operating system manufacturer’s CD.
5-12 Server Configuration and Utilities Compaq SmartStart Installation If you use SmartStart to install the OS, the drivers are installed automatically. Manual Installation If you choose to configure the server without SmartStart, follow this procedure: 1. Insert the Compaq SmartStart and Support Software CD into the CD-ROM drive. 2. Boot your system. 3. Select Manual Installation. 4. Follow the instructions provided by the operating system that you are installing.
5-13 Please read NETWORK.RDM from the NSSD diskettes for further information. Your ProLiant 1850R server comes with one IDE channel to which you can attach IDE devices. For each IDE channel to which you have an attached device, you must load the following drivers found on the NSSD diskette according to the type of device attached: For each IDE channel: LOAD A:\IDE\IDEATA.HAM For an IDE fixed disk : LOAD A:\IDE\IDEHD.CDM For an IDE CD-ROM drive: LOAD A:\IDE\IDECD.CDM Please read STORAGE.
5-14 Server Configuration and Utilities Compaq SmartStart Installation If you use Compaq SmartStart to install the OS, the drivers are installed automatically. Manual Installation If you choose not to let SmartStart configure the server, follow this procedure: 1. Insert the Compaq SmartStart and Support Software CD into the CD-ROM drive. 2. Boot your system. 3. Select Manual Installation. 4. Follow the instructions that display on the monitor.
5-15 SCO OpenServer and SCO UnixWare Device Drivers from Compaq If using the Compaq Integrated Netelligent 10/100 TX Controller on a ProLiant 1850R server and you do not plan to use the SmartStart installation process to setup your server, you must install updated support software for your controller to connect properly to the network, refer to Appendix G, “Updating LAN Drivers” for instructions. Your server must have certain device drivers to operate under the SCO OpenServer and UnixWare 2.1.
5-16 Server Configuration and Utilities The third method would be very similar to the “Manual Path” listed above however you run the Compaq’s System Configuration Utility to configure the system, obtain the appropriate EFS for the SCO operating system release and follow the manufacturer’s installation instructions.
5-17 IBM OS/2 Device Drivers from Compaq If using the Compaq Integrated Netelligent 10/100 TX Controller on a ProLiant 1850R server and you do not plan to use the SmartStart installation process to setup your server, you must install updated support software for your controller to connect properly to the network, refer to Appendix G, “Updating LAN Drivers” for instructions. Your server must have certain device drivers for some server options to operate using IBM OS/2 Warp Server 4.
5-18 Server Configuration and Utilities Compaq SmartStart Installation If you use Compaq SmartStart to install the OS, the drivers are installed automatically. Manual installation If you choose not to let Compaq SmartStart configure the server, follow this procedure: 1. Insert the Compaq SmartStart and Support Software CD into the drive. 2. Boot your system. 3. Select Manual Installation. 4. Follow the instructions that display on the monitor. 5.
5-19 Retail Installation You cannot install OS/2 on a Compaq server using unmodified installation diskettes that come with the OS/2 retail CD follow the procedure given below: 1. Punch out OS/2 SSD diskettes from the Compaq SmartStart and Support Software CD as per the procedure given in the "Manual Installation" section. 2. Use the CPQSETUP utility available on these diskettes to modify your OS/2 installation diskettes. 3. Install OS/2 using the diskettes modified in step 2. 4.
5-20 Server Configuration and Utilities These drivers are located on the Compaq SmartStart and Support Software CD you received with your server. You can use SmartStart to create a Banyan VINES Support Software Diskette (SSD) from Compaq to support a manual installation of Banyan VINES. There are two types of SSDs: LAN Adapter SSD Peripheral Adapter SSD These SSDs contain the README files that list available drivers and driver installation procedures.
5-21 Controller Naming Conventions The Integrated 10/100TX UTP Controller that is embedded in this ProLiant 1850R server utilizes the same drivers as the Compaq NetFlex-3 and Netelligent 10/100 family of controllers. For your convenience, some of the popular operating systems and corresponding driver names are listed in the following table. Table 5-2 Controller Driver Naming Conventions Operating System Driver Type Driver File Name DOS NetWare ODI CPQNF3.COM DOS IBM LAN Server NETFLX3.
5-22 Server Configuration and Utilities Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: F-CH05.
6-1 Chapter 6 Integrated Management Log The Compaq Integrated Management Log (IML) records events and stores them in an easily-viewable form. The Compaq Integrated Management Log records hundreds of events and then marks each event with a time-stamp with oneminute granularity. Events listed in the Compaq Integrated Management Log are categorized as one of four event severity levels: Status—indicates that the message is informational only. Repaired—indicates that corrective action has been taken.
6-2 Compaq Integrated Management Log Compaq Insight Manager Compaq Insight Manager is a server management tool, providing in-depth fault, configuration and performance monitoring of hundreds of Compaq servers from a single management console. System parameters that are monitored describe the status of all key server components. By being able to view the events that may occur to these components, you can take immediate action.
6-3 Printing the Event List NOTE: You can only view the list from the Recovery/Integrated Management Log screen as described above. To print the list, follow the instructions below. 1. From Compaq Insight Manager, select the appropriate server. The selected server is displayed with buttons around its perimeter. 2. Click the Configuration button. 3. Click the Recovery button. 4. Click Print.
6-4 Compaq Integrated Management Log List of Events The event list displays the affected components and the associated error messages. Though the same basic information is displayed, the format of the list may be different depending on how you are viewing it from within Compaq Insight Manager, or from within the Compaq Survey Utility. The table on the following page identifies the event types (affected components) and associated event messages.
6-5 Event Messages continued Event Type POST Error Event Message POST Error: Error message Power Subsystem Power Supply Failure System Power Supply Failure (Power Supply X) Power Supply Inserted System Power Supply Inserted (Power Supply X) Power Supply Removed System Power Supply Removed (Power Supply X) Power Supply Not Redundant System Power Supplies Not Redundant System Configuration Battery Low Real-Time Clock Battery Failing Power Module Failure A CPU Power Module (System Board, Socket
A-1 Appendix A Regulatory Compliance Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
A-2 Regulatory Compliance Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for products marked with the FCC logo United States only This device complies with Part 15 of the FCC Rules.
A-3 Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
A-4 Regulatory Compliance Notices Taiwan Notice Laser Devices The CD-ROM drive contains a laser device. All Compaq systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product.
A-5 Compliance with International Regulations All Compaq systems equipped with CD-ROM drives comply with appropriate safety standards including IEC 825. Laser Product Label The following label or equivalent is located on the surface of your CD-ROM drive. This label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label appears on a laser device installed in your product. Laser Information Laser Type Semiconductor GaAIAs Wave Length 780 nm +/- 35 nm Divergence Angle 53.
A-6 Regulatory Compliance Notices Battery Replacement Notice Your computer is provided with a Real-Time Clock circuit powered by an internal Lithium Manganese Dioxide or Lithium Vanadium Pentoxide battery. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by a Compaq Authorized Service Provider using the Compaq spare designated for this product.
B-1 Appendix B Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: Avoid hand contact by transporting and storing products in static-safe containers.
B-2 Electrostatic Discharge If you do not have any of the suggested equipment for proper grounding, have an Authorized Compaq Reseller install the part. NOTE: For more information on static electricity, or assistance with product installation, contact your Authorized Compaq Reseller. Writer: Michele Wray Project: Compaq ProLiant 1850R Setup and Installation Guide Comments: 333172-002 File Name: I-appb.
C-1 Appendix C Power Cord Set Requirements The power cord set meets the requirements for use in the country where you purchased your equipment. Power cord sets for use in other countries must meet the requirements of the country where you use the server. For more information on power cord set requirements, contact your Authorized Compaq Dealer. General Requirements The requirements listed below are applicable to all countries: The length of the power cord must be at least 6.0 feet (1.
C-2 Power Cord Set Requirements Country-Specific Requirements Use the following table to identify the appropriate accredited agency in your country.
D-1 Appendix D Installing a New Battery The Compaq ProLiant 1850R server has two memory device which requires a battery for retaining stored information. It is on the System Board. This battery is required to maintain their data. System Board Battery Replacement When your server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is usually about five to ten years.
D-2 Installing a New Battery Installing the System Board Battery WARNING: The System Board contains a clock/CMOS lithium battery. The lithium battery may explode if mistreated. The battery is soldered in place and may not be removed. Do not abuse or disassemble. Use only replacement batteries supplied by Compaq Computer Corporation (spare part number 160274-001). To install the new battery, complete the following steps: 1. If the server is on, place it in Standby and disconnect the power cord-(s).
D-3 6. Remove the backing from the adhesive on the hook-and-loop fastener strip. 7. Place the battery and the hook-and-loop fastener strip on the designated chip, as shown in the following illustration. 8. Plug the battery connector onto pins 1-4 of header E2 on the System Board. Figure D-2. 9. Attaching the battery to the designated location Reverse steps 1 through 3 to replace the server cover and cable the server, etc. 10.
D-4 Installing a New Battery 11. Plug in the server and reconnect any external devices. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
E-1 Appendix E Switches and Jumpers When you add or remove a component or change a security feature, you must reconfigure the computer to recognize these changes. If the system configuration is incorrect, your computer may not work properly and you may receive error messages on the screen. Setting the System Board switches is part of the reconfiguration process, along with running the System Configuration utility.
E-2 Switches and Jumpers System Configuration Switch Settings (S1 Settings) The following table defines the function for each switch setting on SW1.
E-3 Processor Switch Settings The following table defines the function for each switch setting on SW1.
E-4 Switches and Jumpers NIC Operating Mode The ProLiant 1850R server comes standard with the Compaq Netelligent 10/100 TX embedded controller. The controller automatically differentiates between the 10Mb and 100Mb environments when the RJ-45 connector is used. SCSI Device Jumper Settings No two SCSI devices connected to the same SCSI controller can have the same SCSI ID.
E-5 System Board Battery Jumper Settings The System Board allows you to add an external battery, if the battery embedded on the System Board fails. A Jumper on header E2 on the System Board allows you to choose the internal battery and an external battery. Placing the jumper on pins 6-7 selects the internal battery. Placing the jumper on pins 5-6 selects the external battery. See Appendix D, “Installing a New Battery,” for more specific information.
F-1 Appendix F Specifications and Connector Interfaces This appendix provides operating and performance specifications for the Compaq Compaq ProLiant 1850R components. For other specifications, refer to the Systems Reference Library CD. ProLiant 1850R Specifications Table 1-1 ProLiant 1850R Specifications Dimensions Height 5.1 in 12.9 cm Depth 22.1 in 56.1 cm Width 17.7 in 45.00 cm 35.0 lbs 15.
F-2 Specifications and Connector Interfaces ProLiant 1850R Specifications Continued Temperature Range Operating Range 50° to 95°F 10° to 35°C Non-operating Range -4° to 122°F -20° to 50°C Operating 8% to 90% 8% to 90% Nonoperating 5% to 95% 5% to 95% 101.7° F 38.
G-1 Appendix G Updating LAN Drivers Introduction This chapter provides installation instructions for installing the appropriate LAN drivers for the Compaq ProLiant 1850R embedded Network Interface controller. LAN driver’s provided with the following operating systems do not provide the correct drivers. CAUTION: Following the operating system’s driver installation procedures without following the instructions below results in error messages and may effect the operation of your server.
G-2 Updating LAN Drivers For Novell Products (NSSD) version 3.22A diskettes CAUTION: You must use drivers from either the Compaq Support Software For Novell Products (NSSD) version 3.22A or from the Compaq website when updating your Compaq LAN drivers. Have these drivers available before you begin your install. Compaq Support Software For Novell Products (NSSD) version 3.22A can be found on the SmartStart and Support Software version 4.1 CD-ROM.
G-3 Setup intraNetWare for Small Business from Compaq Perform the steps below before installing IntraNetWare for Small Business from Compaq. 1. Copy the entire CD source (about 590 megabytes) onto a directory on the systems local hard drive, maintaining directory structure. 2. After copying, delete or rename the following files: CPQNF3.LAN, MSM.NLM, NBI.NLM, and ETHERTSM.NLM.
G-4 Updating LAN Drivers 4. If you are using the Smart Start and Support Software CD-ROM 4.1 to copy the appropriate files type in the following path: (CD Drive letter):\CPQSUPSW\NSSD\NETWORK and press Enter. 5. If you are using diskettes place diskette #3 of the support diskettes you created into the floppy drive of your system. Type in the following path A:\NETWORK and press Enter. 6. When the LAN Driver Options screen appears, scroll down and highlight the following driver: CPQNF3.
G-5 12. If no additional LAN drivers are required for your installation. answer no to this question. 13. Scroll to option Continue installation. This completes your LAN driver update. Your can now to allow your network controller to properly connect to the Network through the embedded controller. LAN Driver Update Procedure NetWare for Small Business 4.11 IMPORTANT: Since NetWare for Small Business 4.
G-6 Updating LAN Drivers LAN Driver Update Procedure For NetWare 3.2 Follow the normal installation procedure for NetWare 3.2. After installation is complete be sure to add the NSSD 3.22A LAN and support drivers from your SmartStart and Support Software CD-ROM or the Support diskettes you create to your ProLiant system in order to be able to connect to your network with the embedded NIC. Installing Windows NT 4.0 LAN Drivers The LAN drivers on the Microsoft Windows NT 4.
G-7 LAN Driver Installation Procedure for Window NT 4.0 When you reach the Network Adapter portion of the OS installation perform the following steps. 1. In the Network Adapter dialog box choose Select for list. IMPORTANT: Do not choose start search. 2. In the Select Network Adapter dialog box choose Have Disk. 3. Insert Diskette # 2 of the Microsoft Support Software for Windows NT 4.0 (NTSSD) disk set. 4.
G-8 Updating LAN Drivers 1. Bring up the MPTS utility by typing MPTS from an OS/2 window or full screen, or by double clicking the Multi-Protocol Transport Services (MPTS) icon. 2. Select Configure. 3. Select LAN adapters and protocols and click Configure. 4. Click Other Adapters... . 5. Insert the OS/2 NIC Software Support Diskette (SSD) #2 Diskette into the floppy drive. 6. Provide the path as A:\IBMCOM and select OK. 7.
G-9 3. Insert the LAT SSD installation diskette and press Enter. The following message is displayed if the Vines server version is less 6.40(0): "NOTE: Compaq Netelligent 4/16 TR UTP/STP controller driver is supported only on VINES 6.40(0) and above. Upgrade your system to VINES 6.40(0)or above to install this driver." 4. Installation of LAT SSD continues and following message is displayed: "Kernel should be rebuilt now to add NetFlex-3 Supplement driver. The NetFlex-3 driver will not work without this.
G-10 Updating LAN Drivers 11. Save the configuration and exit. The following message is displayed: "Building device drivers, please wait ......." 12. The Banyan Server Configuration screen is displayed. Select Return to the System Maintenance Menu. 13. From the System Maintenance menu select Return to the operator menu. 14. From the operator menu select Shutdown Server Software and reboot your server. The server now boots with the Network controller driver configured as part of the VINES Operating System.
Index-1 Index Symbols .CFG files 5-2 .PCF files 5-2 Numbers 1.44 diskette drive installation 3-19 removal 3-19 1.44-MB diskette drive cable 4-8 1.6-inch height drives illustrated 3-32 1.6-inch hot-plug hard drive configuration 1-3, 1-4 1.6-inch SCSI IDs, defined 1-13 100TX Ethernet rate 1-12 10-BaseT rate 1-12 1-inch height drives illustrated 3-32, 3-33 1-inch hot-plug hard drive configuration 1-3, 1-4 1-inch SCSI IDs, defined 1-13 225 watt power supply 1-16 3.5-inch 1.
Index-2 battery, installing D-1 blanking panels 2-7 boot partician 1-17 C cable kit, contents identified 4-8 cable management arm 2-11 cabling 2-32 securing the arm, illustrated 3-37 cable management arm bracket 2-25 cable management arm rack bracket 2-11 installation illustrated 2-29 cable management arm server bracket 2-11 cables 1.
Index-3 Compaq service 2-37 Compaq Survey Utility 6-3 Compaq System Configuration Utility 2-34 Compaq TechNotes 1-9, 4-19 Compaq Web Site xiii component rail attaching to rack server 2-25 Configuration backup 5-8 History Log Files 5-8 configuration and management of server 1-17 configuration using SmartStart 1-18 Configuring Hardware menu 5-4 using .CFG files 5-2 using .
Index-4 documentation and software packs 2-11 documentation kits 2-11 DRAM installed 1-15 Drive bay positions 1-12, 1-14, 4-6 drive installation guidelines 4-7 drive positions 1-12, 1-15 Driver installation NetWare for Small Business G-3 Novell G-1 drives installation guidelines 3-16 dual wide ultra SCSI-3 controller 1-11 E ECC memory 1-15 EISA Configuration Utility 2-9 electrostatic discharge 4-10, B-1 Embedded network interface controllers LAN drivers G-1 ENET controller 1-12 error checking and correcti
Index-5 full duplex ethernet 1-12 full height tape drive 4-6 G Getting Help xiii Grounding Methods B-1 grounding requirements 2-6 H half height device cabling, illustrated 4-18 half-height bay locations 1-3 half-height tape drive 4-6 hard drives 1-12, 1-14 jumper settings 3-17 hard drives, pre-failure warranty 1-24 Hardware configuring hardware menu 5-4 Health logs, server 1-17 History Log Files, configuration 5-8 hot-plug areas accessing 3-31 hot-plug drives 1.
Index-6 installing 3.
Index-7 LAN drivers Continued intraNetWare for Small Business 4.11 G-5 NetWare 3.2 G-6 NetWare for Small Business G-3 NetWare installation G-1 NIC drivers installation overview G-1 OS/2 Warp Connect G-7 OS/2 Warp Server 4.0 G-7 OS/2 Warp Server Advanced 4.0 G-7 OS/2 Warp Server SMP G-7 SunSoft Solaris 2.51 G-10 SunSoft Solaris 2.6 G-10 Sunsoft Solaris versions later than 2.
Index-8 Microsoft Windows NT servers 3.51 5-10 Microsoft Windows NT servers 4.
Index-9 PCI removing boards 5-9 slots 3-10 PCI configuration files See .
Index-10 Rack Continued installation sequence for rack model server 2-8 installing mounting bracket assembly 2-22 internal temperature maximums 2-6 loading server 2-26 Planning and Installation Guide 2-2 power requirements 2-5 Rack Builder program 2-2 room temperature requirements 2-6 server cable management arm 2-28 server cabling 2-32 server safety 2-26 slide rail assembly 2-14 space requirements 2-5 temperature requirements for 2-6 template for server mounting brackets 2-20 tools needed for installation
Index-11 removable media devices installation 3-16 removable media storage 3-16 removable media tray removing 3-25 removable media trays installation and removal 3-25 expansion boards 3-15 3-8 hot-plug power supply 3-34 the removable media tray 3-25 two removable media trays 3-29 removing server rail from outer bracket rail 2-14 illustrated 2-14 resolving resource conflicts 5-2 Resource conflicts, resolving 5-2, 5-9 riser board expansion slots, illustrated 1-10 locating expansion slots 3-10 riser board and
Index-12 Server Continued rear panel connectors 4-2 securing to rack 2-26 turning on the power 2-33 server bracket installation 2-26 server cover removal 3-4 Server Fault Tolerance 1-18 server features 32-MB DRAM installed 1-15 Automatic Server Recovery-2 (ASR-2) 1-20 cache memory 1-10 Compaq Insight Manager 1-19 drive positions 1-12, 1-14, 4-6 expansion slots 1-10 fault tolerance 1-19 front panel LEDs 1-22 hot-plug redundant power supply 1-16 Insight Manager Alert 1-24 integrated 256-KB secondary cache 1-
Index-13 SmartStart Continued device drivers for Sunsoft Solaris 5-19 SmartStart and Support Software CD 2-34, 2-35 SMP operating system support 5-10 space requirements 2-5 specifications F-1 STANDBY switch 3-2 starting the System Configuration utility 5-3 status indicators for Compaq Insight Manager 4-19 status lights See LEDs storage removable media 3-16 storage devices 1-12, 1-14, 4-6 SunSoft Solaris 5-10 LAN driver installation procedures G-10 LAN drivers, installing G-10 website location G-10 Sunsoft
Index-14 Utilities Continued Integrated Remote Console Utility 1-21 Server Parameter Tracking 1-18 Survey Utility 6-3 System Configuration 5-1 System Configuration Utility 2-34 TEST Utility 2-35 V video connector (black) 2-31 connector location 1-7 VINES device drivers 5-19 W warnings rack installation 2-3 server installation 2-4 warranty 1-16 pre-failure 1-24 Website location Compaq G-2 SunSoft Solaris G-10 Wide Ultra2 SCSI 1-2, 1-4, 1-5, 1-9, 1-14, 1-15 wide-utra SCSI devices 1-9 Windows NT device driv
