SM-MMN17-C01 NFC Controller Module with Antenna Datasheet Version 1.2 Smart Approach Co., Ltd. Rm. 5, 3F., No.1, Taiyuan 2nd St., Zhubei City, Hsinchu County 302, Taiwan, R.O.C. +886-3-5601363 www.smart-approach.com.
SM-MMN17-C01 Datasheet Smart Approach Co., Ltd ( S.A. ) retains the right to make changes to its products or specifications to improve performance, reliability or manufacturability. All information in this document, including descriptions of features, functions, performance, technical specifications and availability, is subject to change without notice at any time. While the information furnished herein is held to be accurate and reliable, no responsibility will be assumed by Smart Approach for its use.
SM-MMN17-C01 Datasheet REVISION HISTORY ............................................................................................................................. - 2 CONTENTS ........................................................................................................................................... - 3 FIGURE CONTENTS ............................................................................................................................ - 4 TABLE CONTENTS ............................
SM-MMN17-C01 Datasheet Figure 1 Typical Application ................................................................................................. - 6 Figure 2 Module Block Diagram .......................................................................................... - 7 Figure 3 Reset via VEN pin ................................................................................................. - 12 Figure 4 NFC Module Drawing ..........................................................................
SM-MMN17-C01 Datasheet 1 Introduction This document consists of descriptions and specifications for both functional and physical aspects of the SM-MMN17-C01 NFC reader / writer module. In addition to the datasheet, Smart Approach maintains and extensive device-specific library of support and collateral materials that you may find useful in your application.
SM-MMN17-C01 Datasheet 2 Product Overview SM-MMN17-C01 is full featured NFC controllers designed for integration in portable equipment. It is optimized for low power consumption with fully host controllable power states and for small footprint for portable equipment applications. size-sensitive applications, assures robust performance. The following illustration shows a high-level, generic view of a SM-MMN17-C01 application. Figure 1 Typical Application 2.
SM-MMN17-C01 Datasheet 3 Functional Descriptions This section provides detailed information about how SM-MMN17-C01 module works, what configurations and operational features are available. The following illustration shows the primary functional blocks of SM-MMN17-C01 module. Customized Antenna Figure 2 Module Block Diagram Loop Antenna is Smart Approach customize solution. Antenna matching is also a customize solution.
SM-MMN17-C01 Datasheet 4 Electrical Specifications This section provides the DC characteristics, AC characteristics, recommended operating conditions. It includes information on the various timing functions of the module. 4.1 Pin Description The following Table shows the pin description for SM-MMN17-C01 module. The connection ground is internally connected and should be connected to GND on the main board as well. Table 1 Module Pin Description PIN No.
SM-MMN17-C01 Datasheet 4.2 I2C Address SM-MMN17-C01 I2C 7bit address is defined to 0x28. To write data, the module is addressed using 0x50, to read data, the module is addressed using 0x51. Table 2 I2C Address I2C address (R/W=0, write) I2C address (R/W=1, read) 0x50 0x51 4.3 Temperature Maximum Ratings Thermal specifications for this module have been modeled using a two-layer test board.
SM-MMN17-C01 Datasheet 4.4 DC Electrical Parameters DC Electrical specifications for this module have been modeled using a two-layer test board. Table 4 DC Electrical Specification Value Symbol Power VBAT Units Definition Supply Min Typ Max 3.1 3.3 3.5 Volts 170 mA DC Current IVBAT 4.5 Antenna Specification Antenna specifications for this module have been modeled using a two-layer test board. Table 5 Antenna Specifications Value Item DC Resistance Min Type Max 0.
SM-MMN17-C01 Datasheet 4.6 Power Consumption Table 6 Current Consumption Symbol Parameter Conditions Min Typ Max IHPD Hard power down current - 10.5 12 ISTBY Standby state current VBAT=3.6V - - 20 IACT Active state current VBAT=3.6V - 6 - mA ITVDD Transmitter supply current VBAT=3.1V - 30 100 mA IPMUVCC PMUVCC supply Class B - 1.5 3 Class C - 1 2 VBAT=3.6V, VEN=0V Unit 4.
SM-MMN17-C01 Datasheet Table 9 Power Mode Configuration VBAT VDD_IO VEN Power mode Off Off X Power Off mode On X Off Power Off mode On Off On Low Power Mode On On On Full power mode Note: X: Don t care 4.9 Reset and download concept To enter reset there are 2 ways: - Pulling VEN low (Hard Power Down state) - If VBAT monitor is enabled: lowering VBAT below the monitor threshold (monitor mode, if VEN is kept above 1.
SM-MMN17-C01 Datasheet 5 Ordering Information Table 11 Ordering Information Table Order Number Descriptions SM-MMN17-C01 NFC Controller Module (NXP NPC100) with Antenna Dimension Module: 26.65x10.00 mm; Antenna Area: 32.00x10.00mm Total Size: 63.65x10.00mm - 13 - Revision 1.
SM-MMN17-C01 Datasheet 6 Reliability Verification Table 12 Reliability Item Table No.
SM-MMN17-C01 Datasheet 7 NFC Module Outline The following illustration shows the package drawing for SM-MMN17-C01 module. The drawing contains the detail views, dimensions, tolerances, and notes. Figure 4 NFC Module Drawing - 15 - Revision 1.
SM-MMN17-C01 Datasheet Figure 5 Module FPC Connection Foot Print Figure 6 FPC Wire Dimension - 16 - Revision 1.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Radiation Exposure Statement: The product is a low power device and its output power is lower than FCC SAR exemption level. This module can be used with SM-MMN17-C01. This device is intended only for OEM integrators under the following conditions: 1) 2) The transmitter module may not be co-located with any other transmitter or antenna. The co-transmitting with other radio will need a separate evaluation.
cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
