Installation Manual

ManualsBrandsComnet ManualsElectronicsNetwave Battery Backup Kit With Dual 110Ah Batteries

INSTALLATION AND OPERATION MANUAL

Industrial DC-Battery Power Management System

Thank you for purchasing NetWave® from ComNet. This manual

will cover how to install hardware on your enclosure, Configure

batteries, cabling and mounting of the enclosure.

The NetWave® NWKBB200 DC-Battery Power Solution provides

consistent power for your devices in locations where power

is on a timer or they have frequent blackouts or brownouts.

The NWKBB200 supports AC input ranging from 110 to 277

VAC, and can also support 347 VAC and 480 VAC with an

optional Multi Tap Power Transformer. The intelligent controller

distributes power to the load and batteries when AC power is

available and instantly switches over to DC output only when

AC power is lost. The kit includes valve-regulated lead-acid

batteries, outdoor enclosure, mounting bracket and Smart

DCBattery Power Controller. The aluminum outdoor enclosure

has two 180° door hinges and a pad lockable latch for security.

The enclosure has built in mounting brackets that support pole

and wall mounting.

This manual serves the following

ComNet Model Numbers:

NWKBB200

Summary of content (12 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL Industrial DC-Battery Power Management System This manual serves the following ComNet Model Numbers: NWKBB200 Thank you for purchasing NetWave® from ComNet. This manual will cover how to install hardware on your enclosure, Configure batteries, cabling and mounting of the enclosure. The NetWave® NWKBB200 DC-Battery Power Solution provides consistent power for your devices in locations where power is on a timer or they have frequent blackouts or brownouts.
PAGE 2
INSTALLATION AND OPERATION MANUAL NWKBB200 About This Guide This guide is intended for different users such as engineers, integrators, developers, IT managers, and technicians.
PAGE 3
INSTALLATION AND OPERATION MANUAL NWKBB200 Contents About This Guide 2 Related Documentation 2 Website 2 Safety 2 Overview 5 Legal Information 5 1.0 Introduction 6 2.0 Installation 7 Preparing the Enclosure 7 Mounting the Enclosure 8 Battery Configuration 9 3.0 Controller Configuration 10 TECH SUPPORT: 1.888.678.
PAGE 4
INSTALLATION AND OPERATION MANUAL NWKBB200 Overview Legal Information No part of this document may be reproduced or transmitted in any form or by any means, electronic and mechanical, for any purpose, without the express written permission of ComNet. Copyright Copyright © 2016 Communication Networks, LLC (dba ComNet). All rights reserved. Disclaimer ComNet reserves the right to make changes in specifications at any time without notice.
PAGE 5
INSTALLATION AND OPERATION MANUAL NWKBB200 1.0 Introduction The NetWave® NWKBB200 DC-Battery Power Solution provides consistent power for your devices in locations where power is on a timer or they have frequent blackouts or brownouts. The NWKBB200 supports AC input ranging from 110 to 277 VAC, and can also support 347 VAC and 480 VAC with an optional Multi Tap Power Transformer.
PAGE 6
INSTALLATION AND OPERATION MANUAL NWKBB200 2.0 Installation Preparing the Enclosure The NWKBB200 enclosure has integrated mounting brackets and a bolt on mounting plate simplifying installation. Prepare the mounting plate for DIN Rail installation by loosening the screws in the top corners and removing the mounting plate (the appearance of the included mounting plate may vary). Place the DIN Rail in its desired location.
PAGE 7
INSTALLATION AND OPERATION MANUAL NWKBB200 Mounting the Enclosure The NWKBB200 has rackmounts welded onto the enclosure for ease of installation. The included hose clamps will allow you to mount the enclosure on up to a 3 inch diameter pole or you can wall mount the unit using screws appropriate to your mounting surface. TECH SUPPORT: 1.888.678.
PAGE 8
INSTALLATION AND OPERATION MANUAL NWKBB200 Battery Configuration One the DIN Rail has been installed and the enclosure has been mounted, setup the batteries. We provide four 12VDC batteries that will need to be configured in series since our controller will output 48VDC.
PAGE 9
INSTALLATION AND OPERATION MANUAL NWKBB200 3.0 Controller Configuration The Uninterruptible power supply can be used in many different applications. We recommend the following settings for the NWKBB200 Kit. Set the Charging Current to Max. Set Jump settings to Sealed Lead High. Jumpers are on the bottom right of the controller. TECH SUPPORT: 1.888.678.
PAGE 10
INSTALLATION AND OPERATION MANUAL NWKBB200 Connect your device to the 48VDC @ 5A power source on Pins 1 and 2. Connect AC Power Source to the Controller Once AC power is detected, the LEDs on the front of the controller will light up. Mains or Backup LED will be off when AC power is available and on when powered by the battery. Low Battery or Battery Replacement LED indicates that the battery is below 30% capacity or will stay on if a battery fault is detected.
PAGE 11
INSTALLATION AND OPERATION MANUAL TECH SUPPORT: 1.888.678.
PAGE 12
INSTALLATION AND OPERATION MANUAL NWKBB200 ComNet Customer Service Customer Care is ComNet Technology’s global service center, where our professional staff is ready to answer your questions at any time. Email ComNet Global Service Center: customercare@comnet.net Contact Information ComNet – www.comnet.net North America EMEA, PACRIM, South America ComNet Corporate Headquarters and Customer Support Center Tel: +1-203-796-5300 Tel: +1-888-6789427 Email: info@comnet.