Installation Manual

INS_FVT/FVR40D2I1C4E_REVA 06/22/12 PAGE 9
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR40D2I1C4E
FIGURE 15 – LED INDICATORS
FIGURE 14 – ALARM SWITCH POSITIONS
The mode for alarm operation is configured using a set of two switches labeled ALARM (S2) located on the front panel of the unit. There are two alarm out-
puts on each unit. One on each RJ45 data connector. See Figures 4 & 5 on Pages 3 & 4.
NOTE: The ALARM will also open when Fiber Link
on either SFP port is lost or if Power is lost
on either unit.
GREEN Solid: Link (no activity)
Blinking: Activity
Off: No link
YELLOW Solid: Highest data rate (100Mbs)
ALARM (S2)
Resulting Mode1 2
ON ON
Alarm 1 – SFP 1 Failure
Alarm 2 – SFP 2 Failure
ON OFF
Alarm 1 – SFP 1 or SFP 2 Failure
Alarm 2 – Video Loss
OFF ON
Alarm 1 – SFP 1 Failure or Video Loss
Alarm 2 – SFP 2 Failure or Video Loss
OFF OFF
Alarm 1 – SFP 1 or SFP 2 Failure or Video Loss
Alarm 2 – SFP 1 or SFP 2 Failure or Video Loss
VIDEOIN
1234
GND
+Vin
GND
+Vin
PWR1 PWR2
CONTACTAIPHONE
DATA 2DATA 1
NETWORK
MANAGEMENT
4CHVIDEO TX +
2CHBI-DIRDATA+
4CHCONTACT +
1CHETHERNET
FVT40D 2I1C4E
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO4
POWER
10/100LINK
SFP1
SFP2
SFP2
SFP1
10/100
12 12 12 12
ON
S4
DATA1
IN
ETHE RNET
S3
S2
S1
OUT
DATA2
IN
OUT
ALARM
LE-D
LE-F
CONTACT
C
S
VIDEOIN
1234
GND
+Vin
GND
+Vin
PWR1 PWR2
CONTACTAIPHONE
DATA 2DATA 1
NETWORK
MANAGEMENT
4CHVIDEO TX +
2CHBI-DIRDATA+
4CHCONTACT +
1CHETHERNET
FVT40D2I1C4E
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO4
POWER
10/100LINK
SFP1
SFP2
SFP2
SFP1
10/100
12 12 12 12
ON
S4
DATA1
IN
ETHE RNET
S3
S2
S1
OUT
DATA2
IN
OUT
ALARM
LE-D
LE-F
CONTACT
C
S
OFF RED GREEN FLASHING
SFP SFP not installed No optical link Link is good and is in use
Link is good but is not in
use
VIDEO – No video signal
An active video
signal is present
–
10/100 LINK – No Ethernet signal Ethernet signal linked –
CONTACT (C)
One or more contacts are
open
Fiber link failed
All four contacts
are closed
–
CONTACT (S) –
Supervised contact alarm
or fiber link failed
No supervised contacts in
alarm state
–
LE-D – Quiet / No Audio Audio Present Call button active
LE-F – Quiet / No Audio Audio Present –
DATA IN Tri-state Low state High state Data activity
DATA OUT Tri-state Low state High state Data activity
POWER Unit powered down – Unit powered up –
VIDEOIN
1234
GND
+Vin
GND
+Vin
PWR1 PWR2
CONTACTAIPHONE
DATA 2DATA 1
NETWORK
MANAGEMENT
4CHVIDEO TX +
2CHBI-DIRDATA+
4CHCONTACT +
1CHETHERNET
FVT40D2I1C4E
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO4 POWER 10/100LINK
SFP1
SFP2
SFP2
SFP1
10/100
12 12 12 12
ON
S4
DATA1
IN
ETHERNET
S3 S2 S1
OUT
DATA2
IN
OUT
ALARM
LE-D
LE-F
CONTACT
C
S