Installation Manual

ManualsBrandsComnet ManualsFiber ConverterComFit Quad 10/100/1000Mbps Ethernet Media Converter

INS_CNMC[2,4]SFP[POE][/M]

06/06/12

PAGE 1

INSTALLATION AND OPERATION MANUAL

CNMC[2,4]SFP[POE][/M] Series

10/100/1000MBPS ETHERNET MEDIA CONVERTERS

WITH 100FX AND 1000FX SUPPORT

The ComNet CNMCSFP electrical-to-optical Ethernet media converters accept a

10/100 or 1000 Mbps electrical input and converts this to a 100 or 1000 Mbps

optical output (selected by a dip switch) and the 100/1000 Mbps optical input

back to the 10/100/1000 Mbps electrical output. “Auto-Negotiating” is supported

on the copper interface side. These devices use either one or two optical fibers,

depending upon the selection of sold-separately SFP† optical module. A PoE model,

the CNMCSFPPOE/M meets the IEE802.3at standard and provides 30 watts of PoE+

power. The series consists of a small-size single channel model, CNMCSFP/M; a

ComFit standard size, single-channel model, CNMCSFP; a dual channel model,

CNMC2SFP; and a quad channel model, the CNMC4SFP.

Rev. 03/15/18

This manual serves the following

ComNet Model Numbers:

CNMCSFP/M

CNM CSFPPOE/M

CNM CSFP

CNM C2SFP

CNMC4SFP

Summary of content (8 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series 10/100/1000MBPS ETHERNET MEDIA CONVERTERS WITH 100FX AND 1000FX SUPPORT This manual serves the following ComNet Model Numbers: CNMCSFP/M CNMCSFPPOE/M CNMCSFP CNMC2SFP CNMC4SFP The ComNet CNMCSFP electrical-to-optical Ethernet media converters accept a 10/100 or 1000 Mbps electrical input and converts this to a 100 or 1000 Mbps optical output (selected by a dip switch) and the 100/1000 Mbps optical input back to the 10/100/1000 Mbps electrica
PAGE 2
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 1 – CNMCSFP/M SMALL SIZE UNIT OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CNMCSFP/M MULTI RATE MEDIA CONVERTER FIBER LINK/ACT 1000 FX 100 FX TM POWER CAT5e/6 COPPER BLACK ~/~/+ BLACK WITH WHITE STRIPE Surface Mount Power: 9 – 24 VDC @ 2.5 W max. OR 24 VAC @ 2.5 W max.
PAGE 3
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 3 – CNMCSFPPOE/M SMALL SIZE UNIT OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CAT5e/6 IEEE802.3at (30W) PoE BLACK BLACK WITH WHITE STRIPE Surface Mount Power: 48 – 57 VDC @ 35 W max. FIGURE 4 – CNMCSFPPOE/M SMALL SIZE UNIT FRONT PANEL TECH SUPPORT: 1.888.678.
PAGE 4
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 5 – CNMCSFP COMFIT UNIT OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CAT5e/6 BLACK BLACK WITH WHITE STRIPE Surface Mount Power: 9 – 24 VDC @ 2.5 W max. FIGURE 6 – CNMCSFP COMFIT UNIT FRONT PANEL TECH SUPPORT: 1.888.678.9427 OR 24 VAC @ 2.5 W max.
PAGE 5
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 7 – CNMC2SFP COMFIT UNIT OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CAT5e/6 OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CAT5e/6 BLACK BLACK WITH WHITE STRIPE Surface Mount Power: 9 – 24 VDC @ 5 W max. FIGURE 8 – CNMC2SFP COMFIT UNIT FRONT PANEL TECH SUPPORT: 1.888.678.9427 OR 24 VAC @ 5 W max.
PAGE 6
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 9 – CNMC4SFP COMFIT UNIT OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE CAT5e/6 FIGURE 10 – CNMC2SFP COMFIT UNIT FRONT PANEL REAR PANEL BLACK BLACK WITH WHITE STRIPE Surface Mount Power: 9 – 24 VDC @ 10 W max. OR 24 VAC @ 10 W max. Rack power: Supplied by Rack TECH SUPPORT: 1.888.678.
PAGE 7
INSTALLATION AND OPERATION MANUAL CNMC[2,4]SFP[POE][/M] Series FIGURE 11 – DIP SWITCH SETTINGS Position Resulting Data Rate OFF 1000FX (requires use of Gigabit SFP module) ON 100FX NOTE: Select the Data Rate before powering on the unit. After a Data Rate change, re-cycle power to the unit.
PAGE 8
MECHANICAL INSTALLATION INSTRUCTIONS INSTALLATION CONSIDERATIONS FIGURE A This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity.