WET X Premium Quality All-Weather/All-Purpose Loudspeakers Installation and Operation Manual Models 12" Full-range two-way: WX-1226 • WX-1264 • WX-1266 • WX-1294 • WX-1296 • WX-1299 15" Full-range two-way: WX-1526 • WX-1564 • WX-1566 • WX-1594 • WX-1596 • WX-1599 Dual 18" Subwoofer: WX-218SDF WET SERIES • WET X
Important Safety Instructions Rigging and Electrical Safety Always follow these basic safety precautions when using or installing WET X loudspeakers and accessories: DANGER: The loudspeakers described in this manual are designed and intended to be ‘flown’ or suspended using a variety of rigging hardware, means, and methods. Installation of loudspeakers should only be performed by trained and qualified personnel.
Table of Contents Important Safety Instructions ������������������������������������������������������������������������������������������������������������������������������������������������2 Introduction ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������3 Unpacking and Inspection ���������������������������������������������������������������������������������������������������������
Unpacking and Inspection System Information Community WET X loudspeakers are engineered and manufactured to be rugged and they are carefully packed in sturdy cartons. Make sure that the number of cartons shown on the freight documents have actually been delivered. It is wise to thoroughly inspect each unit after it has been removed from the packaging, as damage could occur during shipping.
Product Features Identification Typical WET x 12-inch or 15-inch Full-range Model 1/2"-13 Safety Attachment Point (user must supply appropriate fastener and safety cable) Bracket Rigging Points (sides) Grille SJOW Input Cable Gland Nut Grille Retention Screws (16) Bracket Angle Securing Bolt Bracket slot Rigging Points (sides) Front Rear Typical WET X Subwoofer (WX 218SDF shown) Subwoofer Enclosure Grille Retention Screws Rigging Points (1/2"-13 hex bolts and washers) Mounting Brackets Gril
Rigging / Suspension and Safety TERMINOLOGY: The terms “rigging", “flying" and “suspension" are often used interchangeably to describe the installation of loudspeaker systems above ground level. None of these terms pertain to, or attempt to describe, the actual method that is used (cables, brackets, chains, etc.). DANGER: The loudspeakers described in this manual are designed and intended to be suspended using a variety of rigging hardware, means, and methods.
Installation Before you start Rigging Bolt q Read all instructions and gather tools necessary before starting the installation. Please read all safety instructions and warnings regarding rigging and installation of the loudspeaker. The "q" preceding each step can be used to check off each step as it is completed (or applicable). Every effort has been made to ensure that the information contained in this manual was complete and accurate at the time of printing.
Mount the loudspeaker (cont'd) q Attach the provided 2" gaskets to the inside surface of the bracket arms. With the adhesive side facing the inside of the bracket, align with the large hole and press into place. q Lift the loudspeaker into place between the bracket arms. Attach the loudspeaker to the bracket using the 1/2"-13 hardware as shown in Figure 3. Repeat for the opposite side. Tighten bolts to finger tight (enough to hold the speaker in position). stated enclosure IP54 rating.
Wiring and Electrical Safety All standard WET X Series loudspeakers come with an attached SJOW rated input cable, 12' (4m) in length and colored to match the enclosure. The cable enters the enclosure through a waterproof gland nut. The other end of the cable is un-terminated. Beyond this length, line-loss calculations should be performed when selecting additional wiring to prevent losses in output due to voltage drops due to increased impedance.
Subwoofer Installation Final Assembly and Testing The leg brackets are attached to the subwoofer when shipped. Remove and discard the hardware holding the subwoofer to the shipping pallet. q Attach a safety cable to the attachment point on the rear of each loudspeaker. The safety cable and (1/2"-13) attachment hardware are not included. Please consult a structural engineer for the appropriate cable for the load and application.
Technical Drawings Typical 12-inch 2-way Loudspeaker 4.63" (117 mm) Center of Gravity 12.90" (327 mm) Center of Load 16.0" (406 mm) 1/2"-13 Hang Point Center of Gravity 1/4"-20 Bracket Locking Point 15.0" (381 mm) 30.50" (774 mm) 9.5" (241 mm) Front Sides Center of Gravity Top of Cabinet 2" (50 mm) 9.14" (232 mm) 17.0" (431 mm) 1/2"-13 Safety Hardware Insert Point Back Top / Bracket Center Line 12" (305 mm) 8" (203 mm) Slot 0.41" x 1.59" (11 mm x 41 mm) Typical 4" (102 mm) 1.
Technical Drawings Typical 15-inch 2-way Loudspeaker 4.63" (118 mm) Center of Gravity 1/2"-13 Hang Point Center of Gravity 15" (381) 19.5" (495 mm) 1/4"-20 Bracket Locking Point 17.13" (435 mm) 33.63" (854 mm) Front 11.5" (292 mm) Sides 12.25" (286 mm) Top of Cabinet 2.0" (51 mm) back Center of Gravity 20.5" (521 mm) 1/2"-13 Safety Hardware Insert Point Top / Bracket Center Line 12" (305 mm) 8" (203 mm) Slot 0.41" x 1.59" (11 mm x 41 mm) Typical 4" (102 mm) 1.31" (33 mm) 1.5" (38 mm) 1.
Technical Drawings Typical Subwoofer (WX 218SDF shown) 24.88" (632 mm) 30.76" (781 mm) Bracket 1/2"-13 Mounting Points (8 Typical) 3.0" (76 mm) 49.80" (1265 mm) Sides Ends Ø .63" (Ø 76 mm) (4 places) 18.63" (473 mm) 24.32" (618 mm) 45.71" (1161 mm) 48.0" (1219 mm) Front FIELD SERVICE Any driver or crossover service required is accessed from the front of the enclosure by removing the front grille and removal of the LF driver or the horn assembly.
Specifications MODEL WX-1226 WX-1264 WX-1266 WX-1294 Loudspeaker Type 2-way, full-range Driver Complement LF: 1 x 12" weather-treated cone, HF: 1 x 1.
Warranty Information Specifications MODEL WX-218SDF Loudspeaker Type Subwoofer (down-fire) Driver Complement LF: 2 x 18" weather-treated cone Coverage Pattern (H x V) 360° x 180° Operating Range (-10 dB) 35 Hz - 500 Hz Frequency Response (-3 dB) 47 Hz - 450 Hz Input Ratings 1400W RMS, 2800W Program 74.8 volts RMS, 149.7 volts momentary peak TRANSFERABLE WARRANTY “(LIMITED)" VALID IN THE USA ONLY The WET X Loudspeakers are designed and backed by Community Professional Loudspeakers.
WET X Premium Quality All-Weather/All-Purpose Loudspeakers Note: Every effort has been made to insure that the information contained in this manual was complete and accurate at the time of printing. However, due to ongoing technical advances, changes or modifications may have occurred that are not covered in this manual. Visit Community at www.communitypro.com for the latest version of this manual and the most recent product information.
