R6-51 R6-BASSHORN INSTALLATION / OPERATION MANUAL Weather-Resistant, High-Fidelity, High Output Loudspeaker Systems
EC STATEMENT OF CONFORMITY E C S TAT E M E N T O F C O N F O R M I T Y This document confirms that the range of products of Community Professional Loudspeakers bearing the CE label meets all of the requirements in the EMC directive 89/336/EEC laid down by the Member States Council for adjustment of legal requirements. Furthermore, the products comply with the rules and regulations referring to the electromagnetic compatibility of devices from 30-August-1995.
WELCOME TO COMMUNITY A TRADITION OF EXCELLENCE AND I N N O VAT I O N . . . S PA N N I N G M O R E T H A N 4 0 Y E A R S ! Since the founding of our company in 1968, Community has been a constant developer and innovator of loudspeaker technology. Many of our engineering achievements were undertaken to solve problems, when no prior solutions existed, while others were the result of simply seeing a better way to do things.
TABLE OF CONTENTS TOPICS EC Statement of Conformity ...................................................................................................... Page 2 Welcome to Community ............................................................................................................ Page 3 Important Safety Information ..................................................................................................... Page 5 Unpacking, Inspection, and Damage Claims ..................................
IMPORTANT SAFETY INFORMATION I M P O R TA N T S A F E T Y I N F O R M AT I O N Always follow these basic safety precautions when using or installing R-Series loudspeakers and accessories: Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions, particularly those pertaining to rigging, mounting, suspension of the product, and electrical connections.
UNPACKING U N PA C K I N G A N D I N S P E C T I O N R-Series loudspeakers are inherently rugged and are carefully packed in sturdy cartons. However, it’s wise to thoroughly inspect each unit after it has been removed from the packaging, as damage may have occurred during shipping. SHIPPING CLAIMS Please note that once the shipment has left your dealer or the Community factory, the responsibility for damage is always borne by the freight company.
INTRODUCTION / FEATURES INTRODUCTION TO THE R6-BASSHORN AND THE R6-51BIAMP LOUDSPEAKERS All-Weather, All-Purpose The R6-BASSHORN and R6-51 are large-format, very high-power loudspeakers intended for use in demanding applications that require extreme output levels. They are designed to handle the harshest outdoor environmental conditions, but it should be kept in mind that they are often the ideal choice for indoor environments as well.
PRODUCT DESCRIPTIONS R6-BASSHORN PRODUCT DESCRIPTION The R6-BASSHORN is a high-output low frequency system designed for long throw applications in sports arenas, stadiums, and other large facilities that require high power levels coupled with superb clarity. The R6-BASSHORN has been designed to work in an array with like units. As more units are employed, the control of acoustic dispersion becomes increasingly more directional and more effective at focusing the sonic energy.
QUICK START-UP GUIDE P H Y S I C A L F E AT U R E S O F T H E R 6 & R 6 - 5 1 NOTE: The numerical callouts show the typical location of the primary physical features of the R6 and R6-51 loudspeaker enclosures. Not all mounting points, grille fasteners, or supplementary mounting holes are shown in order to make the illustration as clear as possible. 1 2 3 FEATURE DESCRIPTION Mounting/Rigging Points Four total; two on the rear and one each on the top and bottom.
SIGNAL PROCESSING H I G H - PA S S F I LT E R The R6-51 and the R-6 BASSHORN use fully horn-loaded low frequency drivers. The specified low frequency response is 45 Hz. Any attempt to reproduce significant levels below this frequency can result in over-excursion of the low frequency drivers. For this reason a 45 Hz electronic high-pass filter with a minimum slope of 12 dB per octave must be employed.
POWER AMPLIFICATION POWER RATING Power handling of the Low Frequency section of the R6-51BIAMP and the R-6 BASSHORN is rated at 1200 Watts continuous and 3000 Watts program. An amplifier that is capable of providing a continuous output of 2500 Watts to 3000 Watts into a 4 ohm load is recommended. It is better to oversize the amplifier than to undersize it. The Mid/High Frequency section of the R6-51BIAMP is rated at 450 Watts continuous and 1100 Watts program.
ELECTRICAL INSTALLATION block, crimped connections, or wire-nuts. Make sure to provide all connections with a weather-resistant treatment if used outdoors or in potentially harsh indoor environments. This can take the form of a weatherproof junction box (recommended), do not remove the gland nut that attaches the cable to the lower rear of the loudspeaker, as this will compromise the weather integrity of the enclosure. All terminations should conform to local electrical codes and industry best practices.
MOUNTING POINT DIMENSIONS Community R6-51 & R6-BASSHORN Installation / Operation Manual — Page 13
MECHANICAL INSTALLATION GENERAL MOUNTING INSTRUCTIONS The R6-51 and the R-6 BASSHORN are each equipped with four primary mounting points. Each point consists of a 1/2”-13 threaded inset. In all cases, a minimum of two points - on opposite sides of the enclosure - (total of four points) should be used to mount R6-51 or R-6 BASSHORN loudspeaker.
MECHANICAL INSTALLATION For many applications the top and bottom mounting points, used together, are sufficient for secure mounting of these loudspeakers. When a safety-cable mounting point is required, one or both of the rear mounting points may be used. In applications where the loudspeaker may be subjected to high wind loads or other unusual stresses, Community recommends that the loudspeaker be mounted from the top, the bottom, and at least one of the rear mounting points.
RIGGING CONSIDERATIONS RIGGING SAFETY DANGER: The loudspeakers described in this manual are designed to be ‘flown’ or suspended for maximum acoustical performance using a variety of rigging hardware, means, and methods. It is essential that all installation work involving the suspension of these loudspeaker products be performed by competent, knowledgeable persons who understand safe rigging practices. Severe injury and/or loss of life may occur if these products are improperly installed.
RIGGING CONSIDERATIONS which allows the load applied to the threaded inserts on the loudspeaker enclosure to minimize off-axis stresses, thus preserving the integrity of the insert point. When using Hoist Rings the same precautions should be taken to properly seat the Hoist Ring as when seating a shoulder eye-bolt. Hoist Rings are not normally found in hardware stores but can readily be obtained from industrial suppliers.
TECHNICAL SPECIFICATIONS Model: Loudspeaker Type: Operating Range: Max Input Ratings: R6-51BIAMP R6-BASSHORN Three-way, Horn Loaded, Triaxial, WeatherResistant Low Frequency Bass Horn System, 45 Hz to 16 kHz 45 Hz to 500 Hz 50 Hz to 16 kHz (± 4dB) 55 Hz to 450 Hz (± 4dB) LF: 1200W continuous, 3000W program 69 volts RMS, 155 volts momentary peak 1200W continuous, 3000W program MF/HF: 450W continuous, 1100W program 60 volts RMS, 133 volts momentary peak Sensitivity 1W/1m: (1/3 octave bands) Maxi
TECHNICAL SPECIFICATIONS (CONT’D) Model: R6-51BIAMP R6-BASSHORN LF: 6 x 12” weather-treated, Ferrofluid-cooled MF: 6 x M200 2” exit, non-metallic diaphragm HF: 6 x 1” exit, titanium diaphragm LF: 6 x 12” weather-treated, Ferrofluid-cooled LF: 40-600 Hz Bandpass / 45 Hz High-Pass LF: 150–300 Hz Crossover / 40 Hz High-Pass Drivers: Recommended Signal Processing: Input Connection: MF/HF: 600 Hz High-pass (2) 12 ft x 16-2 SJOW Neoprene Cable Enclosure: Hand-laminated fiberglass, light grey gelcoat **
SYSTEM OPTIMIZATION COMMISSIONING THE SYSTEM Commissioning is the process of optimizing the performance of a sound system after it has been installed. There are several important steps in commissioning a system; these include the following: 1. Verifying the proper operation of each system component: a) Every source such as mixers, microphones, CD players, audio feeds from other locations, and so on, should be tested independently of the newly installed system to insure that they are working properly.
INTERNAL WIRING GUIDE R6-51BIAMP WIRING R6-BASSHORN WIRING Community R6-51 & R6-BASSHORN Installation / Operation Manual — Page 21
IN CASE OF DIFFICULTY SYMPTOM PROBABLE CAUSE WHAT TO DO No Sound. Equipment is turned off. Check and make sure that all equipment in the audio signal path is turned on. Amplifiers should not be turned on until all equipment before it is turned on. No Sound. Bad or open connection. Make sure the signal and input wire connections for all connectors in the system and all terminal screws are properly connected or soldered. Make sure all wire and cables are intact and not severed or damaged. No Sound.
FIELD & WARRANTY SERVICE FIELD SERVICE Drivers and crossovers are accessible from the front of the enclosure by removing the screws around the edge of the grille. For warranty repair, contact Community directly or ask us for the location of your nearest Authorized Service Center.
WARRANTY SERVICE • A complete description of the problem experienced, including a brief description of how the equipment is being used and with what brand, model and output power of amplifier. Upon receipt, the service center will determine if the problem is covered under warranty. If covered under this warranty, the product will be repaired or replaced, at Community’s option, and returned to the owner freight prepaid.
INSTALLATION NOTES NOTES: —————————————————————————————————————————————————— —————————————————————————————————————————————————— —————————————————————————————————————————————————— —————————————————————————————————————————————————— —————————————————————————————————————————————————— —————————————————————————————————————————————————— —————————————————————————————————————————————————— SYSTEM SETTINGS: Project Name___________________________________ Location_______________________________________ Date___________
The THE COMPLETE R-SERIES FAMILY R.25 R.5 Two-way, full-range 100 Hz to 16 kHz LF 1 x 8", HF 1 x ¾" 200W RMS, 500W PGM, 8 ohms Available coverage pattern: 90° x 40° Two-way, full-range 85 Hz to 16 kHz LF 1 x 12", HF 1 x 1" 200W RMS, 500W PGM, 8 ohms Available coverage patterns: 60° x 60°, 90° x 40°, 90° x 90° For portable systems and as short throw fill loudspeakers. For short-to-medium throw applications like gyms and small seating areas. R.5COAX R.
R-SERIES OPERATING DISTANCES Community R6-51 & R6-BASSHORN Installation / Operation Manual — Page 27
Community Professional Loudspeakers 333 East Fifth Street Chester, PA 19013-4511 USA TEL: 1-(610) 876-3400 FAX: 1-(610) 874-0190 www.communitypro.
