R-Series Installation and Operation Manual Models: R.15COAX, R.35COAX, R.
IMPORTANT SAFETY INSTRUCTIONS RIGGING AND ELECTRICAL SAFETY Always follow these basic safety precautions when using or installing R-Series loudspeakers and accessories: DANGER: The loudspeakers described in this manual are designed and intended to be ‘flown’ or suspended using a variety of rigging hardware, means, and methods. Installation of loudspeakers should only be performed by trained and qualified personnel.
UNPACKING AND INSPECTION SYSTEM INFORMATION Community R-Series loudspeakers are engineered and manufactured to be rugged and they are carefully packed in sturdy cartons. Make sure that the number of cartons shown on the freight documents have actually been delivered. It is wise to thoroughly inspect each unit after it has been removed from the packaging, as damage could occur during shipping.
PRODUCT FEATURES IDENTIFICATION TYPICAL R.15 FULL-RANGE MODEL Bracket / Yoke Weather Cover 3-Layer WeatherStop™ Grille Gland Nut 13.5mm (.5") ID 8mm Rigging Points (2 sides) 8mm Rigging Points (2 sides) FRONT 3.5 x 13mm Pan Head Screws (x4) Safety Attachment Point (user must supply appropriate fastener and safety cable) REAR TYPICAL R.35 FULL-RANGE MODEL Bracket / Yoke 3-Layer WeatherStop™ Grille 8mm Rigging Points (2 sides) Weather Cover Gland Nut 13.5mm (.
RIGGING / SUSPENSION AND SAFETY TERMINOLOGY: The terms “rigging", “flying" and “suspension" are often used interchangeably to describe the installation of loudspeaker systems above ground level. None of these terms pertain to, or attempt to describe, the actual method that is used (cables, yokes, chains, etc.). DANGER: The loudspeakers described in this manual are designed and intended to be suspended using a variety of rigging hardware, means, and methods.
INSTALLATION BEFORE YOU START q Read all instructions and gather tools necessary before starting the installation. Please read all safety instructions and warnings regarding rigging and installation of the loudspeaker. The "q" preceding each step can be used to check off each step as it is completed (or applicable). Every effort has been made to ensure that the information contained in this manual was complete and accurate at the time of printing.
MOUNT THE LOUDSPEAKER The factory yoke uses threaded studs and a nut / lock washer / flat washer combination rather than bolts. This makes it easier to attach the loudspeaker to the yoke after the yoke is mounted to the support structure. q Attach the loudspeaker to the yoke. See Figure 3. Screw an 8mm stud into each side of the loudspeaker so that it protrudes about 3/4" (19mm). Place the rubber washers on the studs and then lift the loudspeaker into place between the yoke arms. Attach as shown.
WIRING AND ELECTRICAL SAFETY All standard R.15 and R.35 loudspeakers are provided with two methods of connecting the amplifier to the loudspeaker: a standard NL4-type locking connector, and a pressurescrew terminal strip. The loudspeaker is intended to be connected directly to the amplifier. If installed outdoors, the insulation of the installerprovided cabling should be resistant to water, the effects of temperature, and the effects of ultraviolet radiation from the sun.
INPUT PANEL CONNECTIONS R.15: The connectors are wired in parallel. If utilizing the NL4-type connector, refer to the detail inset. If utilizing the weather cover, insert the cable end through the gland nut and weather cover, and wire the terminal strip. Set the Music/Voice and Voltage selector switches according to your application (see Figure 5a). + from Amplifier R.
FIELD SERVICE Any driver or crossover service required is accessed from the front of the enclosure by first removing the front grille and then unscrewing and removing the LF driver or the horn assembly. Take note of wiring positions prior to removing any drivers from the loudspeaker. In order to maintain the weather resistance, components and assemblies must not remain removed from the loudspeaker any longer than needed for replacement.
MAINTAINING WEATHER RESISTANCE GUIDELINES FOR R-SERIES OUTDOOR USE R-Series is suitable for outdoor installation when used as recommended. For best results in outdoor applications, follow these guidelines: • Always orient the loudspeaker so the mouth of the horn is, at a minimum, pointing at least 5 degrees downward. Failure to do this could result in water collecting inside the enclosure under extreme weather conditions.
SPECIFICATIONS MODEL Loudspeaker Type R.15COAX R.35COAX R.35-3896 2 way, full range, coaxial 2 way, full range, coaxial 3 way, full range, triaxial LF: 1 x 10" cone, HF: 1 x 1.25" exit compression driver LF: 1 x 8" cone, MR: 2 x 2.35" MultiSource Waveguide compression HF: 1 x 1" exit compression driver LF: 1 x 6.5" carbon ring cone, Driver Complement HF: 1 x 1.
TECHNICAL DRAWINGS TYPICAL R.15 FULL-RANGE LOUDSPEAKER 0.83" (21 mm) Center of Gravity 10.2" (259 mm) 4.83" (123 mm) 0.6" (15 mm) 10.15" (258 mm) 2" (51 mm) Top Center Line M8 Hang Point / Center of Gravity 7.08" (180 mm) Center of Gravity 9.03" (230 mm) 4.52" (115 mm) Safety Cable Attachment Point Front Sides 10.38" (263.7 mm) 5.2" (131.8 mm) Ø 0.51" (Ø 13 mm) Ø 0.35" (Ø 9 mm) Ø 0.35" (Ø 9 mm) 2.6" (66 mm) 2.6" (66 mm) Yoke Hole Dimensions R.15COAX, R.35COAX, R.
TECHNICAL DRAWINGS TYPICAL R.35 FULL-RANGE LOUDSPEAKER 0.84" (21mm) 13.5" (343mm) 1" (25mm) Center of Gravity 8.22" (209mm) 13" (330mm) Top 3.17" (81mm) Center Line M8 Hang Point / Center of Gravity 8.54" (217mm) 11" (279mm) Center of Gravity 5.5" (140mm) Safety Cable Attachment Point Front Sides 12.12" (307.7 mm) Ø 0.51" (Ø 13 mm) 6.06" (153.9 mm) 1.58" (40 mm) 0.98" (25 mm) Ø 0.35" (Ø 9 mm) 8 places 2.6" (66 mm) 2.6" (66 mm) 4.65" (118.1 mm) 4.65" (118.
ACCESSORIES WARRANTY INFORMATION R-VTY15 VARY-TILT YOKE FOR R.15 TRANSFERABLE WARRANTY “(LIMITED)" VALID IN THE USA ONLY Provides pan-tilt operation. Zinc-rich epoxy dual-layer powder-coated steel with hardware, color-matched to loudspeaker. R-VTY35 VARY-TILT YOKE FOR R.35 Provides pan-tilt operation. Zinc-rich epoxy dual-layer powder-coated steel with hardware, color-matched to loudspeaker. The R-Series Loudspeaker Systems are designed and backed by Community Professional Loudspeakers.
R-Series ©2013 Community Professional Loudspeakers Community Professional Loudspeakers 333 East Fifth Street, Chester, PA 19013-4511 USA Phone: (610) 876-3400 • Fax: (610) 874-0190 www.communitypro.
