Model No. PRWX50-H-PC-4K-BZ PRWX80-H-PC-4K-BZ USE AND CARE GUIDE POWERWALL X LED WALLPACK Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-877-527-0313 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Commercial Electric through the purchase of this LED flood light.
Table of Contents Table of Contents......................... 2 Safety Information....................... 2 Warranty.......................................... 3 Pre-Installation.............................. 4 Planning Installation...................... 4 Specifications.................................... 4 Tools Required................................. 4 Package Contents............................ 5 Hardware Included........................... 5 Installation....................................
Warranty This is a limited warranty offered by Commercial Electric for a period of five years from the date of purchase to its customers. Commercial Electric warrants to customers that the products will be free from defects in material and workmanship.
Pre-Installation PLANNING INSTALLATION Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware not shown to actual size. CC BB AA DD Part Description AA Quantity #8-32 x 3/4 in.
Pre-Installation (continued) ☐ ☐ The fixture can be mounted in the following two ways: ˜ Junction Box Mount: Use a junction box to mount the fixture. ˜ Surface Conduit Mount: The fixture can also be mounted directly on the wall surface using conduit entry. When mounting fixture, for Dusk to Dawn operation, make sure the photocell orientation is at the top for wall mount, in an area that receives daylight and not too close to reflective surfaces.
Installation (continued) the 2 Removing Mounting Plate ☐ Loosen the mounting plate tightening screw (C) using a hex head screwdriver (CC) and remove the mounting plate (F) from the fixture. (fig.5) F NOTE: The mounting plate tightening screw (B) comes pre-installed on the light fixture. The tightening screw should not be completely removed. CC C (fig 5).
Installation (continued) Electrical 4 Making Connections ☐ If necessary, strip 3/8 in. of insulation from junction box and lighting fixture wires (fig 7). ☐ Affix the fixture hands-free hanging wire hook (the metal cable found on the back of the fixture) to the small U-shaped slot located on the bottom of the mounting plate (F) (fig 8). This hanging wire allows the fixture to hang in place while freeing both hands for your electrical connections. (fig 7).
Installation (continued) WHEN USING SIDE CONDUIT ENTRIES (No junction box present) ☐ Remove the conduit entry knock-out (B) on the sides of the light fixture (A). ☐ Thread the wires through the conduit entry on the mounting plate (F) as shown in fig 10. Secure the conduit to the mounting plate (F) and make wire connections as shown in fig 10. ☐ Hang light fixture (A) on mounting plate (F). ☐ Tighten the mounting plate tightening screw (C) to secure light fixture to the mounting plate (F).
Installation (continued) FOR NON-DIMMING ELECTRICAL WIRING (Follow these steps when NOT wiring to a 0-10V dimmer). Gray (-) Dimming Purple (+) Dimming Black (Line) ☐ ☐ Junction Box Connect lighting fixture black wire to junction box black wire (line), lighting fixture white wire to junction box white wire (common), and the lighting fixture green wire to the junction box ground wire (fig 11).
Installation (continued) 5 Mounting the Light Fixture F ☐ Once electrical connections are complete, push wires and connections into the junction box and hang the fixture by attaching the back of the fixture to the mounting plate (F). ☐ Tighten the one mounting plate tightening screw (C) to secure fixture to the mounting plate (F). (fig. 13) C CC (fig 13). 6 ☐ Caulking Around the Light Fixture Caulk around the back face of the light fixture as shown in fig 14 with silicone sealant (not included).
Operation Selecting Dusk-to-Dawn or SwitchActivated Control AUTOMATIC NIGHTTIME ON OPTION 1: DUSK-TO-DAWN OPERATION Dusk-to-dawn operation enables the light fixture to automatically turn ON when dark outside and turn OFF when the sun rises, thus saving you energy. ☐ To enable dusk-to-dawn operation, remove the black opaque cap cover (D) installed on the fixture. Note: Ensure the photocell is unobstructed.
Care and Cleaning ☐ appearance, clean the light fixture with clear water and a soft, damp cloth only. ☐ Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints, solvents, or any other chemicals on this light fixture. They could cause a premature deterioration of the finish and may void the warranty. ☐ Do not spray the light fixture with a hose or power washer. Troubleshooting Problem Possible Cause Solution Check if circuit breaker is tripped.
Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-877-527-0313 HOMEDEPOT.COM Retain this manual for future use.
