Installation Guide

ManualsBrandsCommercial Electric ManualsCommercial Lighting3 ft. 36-Watt Equivalent Integrated LED White Shop Light with Pull Chain 3000 Lumens 4000K Bright White

Item # 1005535864

Model # 55702141

PACKAGE CONTENTS

Part Description Quantity

A Shop Light 1

HARDWARE INCLUDED

Part Description Quantity

AA Mounting Chain 2

BB Drywall Anchor 2

CC Hook Screw 2

NOTE: Keep your receipt and these instructions for proof of purchase.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the

fuse or turn off the circuit breaker before removing an existing light xture or installing the new one.

If you are unfamiliar with electrical installations, we recommend you contact a qualied electrician to do the installation.

USE AND CARE GUIDE

3 FT. SHOP LIGHT WITH PULL CHAIN

INSTALLATION PREPARATION

Select a suitable location that can support the weight of the xture. Determine the method for mounting the xture before

drilling, based on the type of ceiling.

1. Mark two spots on the ceiling 35.82 in. (910mm) apart for suspension mounting before the installation.

MOUNTING TO A DRYWALL CEILING:

a. Drill a 1/8-in. pilot hole into each of the screw locations marked on the ceiling. You can also use an awl or nail to dimple the

screw holes.

b. Install a drywall anchor (BB) and a hook screw (CC) in each drilled mounting hole.

NOTE:

The drywall anchors (BB) are only to be used for mounting the xture to plaster or drywall surfaces

MOUNTING TO A WOOD CEILING:

a. Drill a 1/16 in. diameter pilot hole in the ceiling. Make sure to fasten the combo wood-machine end into the metal hook.

Tighten the hook screw (CC) into the wood.

35.82 in.

910mm

AA BB CC

Summary of content (6 pages)

PAGE 1
Item # 1005535864 Model # 55702141 Use and Care Guide 3 FT. Shop light with PULL CHAIN Package Contents Part A Description Shop Light Quantity 1 A Hardware Included Part AA BB CC Description Mounting Chain Drywall Anchor Hook Screw Quantity 2 2 2 AA BB CC NOTE: Keep your receipt and these instructions for proof of purchase. WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off.
PAGE 2
. Attach the S hook at the bottom of the mounting chain (AA) to the hanger on the shop light (A). Repeat this step on the other side of the fixture. Then close all hooks with pliers to secure them. AA Hanger A 3. Hang the shop light (A) by placing one chain (AA) over each hook (CC) that has been installed on the ceiling. 4. Adjust chains to level light. The fixture must hang at least 3 in. from the ceiling. CC AA A 5. Plug the electrical plug adapter into an electrical outlet. 6.
PAGE 3
Care and Cleaning CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring. Troubleshooting Minor problems often can be fixed without the help of an electrician.
PAGE 4
Artículo # 1005535864 Modelo # 55702141 GUÍA DE USO Y CUIDADO LÁMPARA DE TALLER DE 3 PIES CON CADENA CONTENIDO DEL PAQUETE Pieza Descripción A Dispositivo de luz Cantidad 1 A MATERIALES INCLUIDOS Pieza AA BB CC Descripción Cadena de soporte Anclaje para yeso Tornillo de gancho Cantidad 2 2 2 AA BB CC NOTA: Guardar el recibo de compra y estas instrucciones como prueba de compra. ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA.
PAGE 5
2. Fije el gancho S en la parte inferior de la cadena de montaje (AA) a la percha en la lámpara de taller (A). Repita este paso en el otro lado del aparato. Luego cierre todos los ganchos con alicates para asegurarlos. AA Percha A 3. Cuelgue la lámpara de taller (A) colocando una cadena (AA) sobre cada gancho (CC) que se ha instalado en el techo. 4. Ajuste las cadenas para nivelar la lámpara. La lámpara debe colgar al menos 3 pulgadas del techo. CC AA A 5.
PAGE 6
Cuidado y limpieza PRECAUCIÓN: tes de limpiar la lámpara, desconecte el suministro eléctrico hacia ésta apagando el cortacircuitos o extrayendo el fusible de la caja de fusibles. Limpie la lámpara con un paño suave y seco. No utilice limpiadores con productos químicos, solventes o abrasivos. No use limpiador líquido en las bombillas LED, en la unidad LED ni en los cables que están dentro de la lámpara. Solución de problemas Los problemas menores pueden arreglarse sin ayuda de un electricista.