Installation Guide

ManualsBrandsCommercial Electric ManualsCommercial Lighting40 in. 64-Watt Equivalent Black Brushed Nickel PIR Motion Sensor LED Shop Light Linkable with Motion Timer 3000 Lumens

Item # 1005535874

Model # 55701141

PACKAGE CONTENTS

Part Description Quantity

A Shop Light 1

B Electrical Plug Adapter 1

5 ft. Power Cord /

Linking Cable

D End-to-End Connector 1

HARDWARE INCLUDED

Part Description Quantity

AA Mounting Chain 2

BB Drywall Anchor 2

CC Hook Screw 2

DD Cable Tie 1

NOTE: Keep your receipt and these instructions for proof of purchase.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the

fuse or turn off the circuit breaker before removing an existing light ﬁxture or installing the new one.

If you are unfamiliar with electrical installations, we recommend you contact a qualiﬁed electrician to do the installation.

USE AND CARE GUIDE

40IN. SHOP LIGHT WITH MOTION SENSOR

INSTALLATION PREPARATION

Select a suitable location that can support the weight of the ﬁxture. Determine the method for mounting the ﬁxture before

drilling, based on the type of ceiling.

1. Mark two spots on the ceiling 34.96 in. (888mm) apart for suspension mounting before the installation.

MOUNTING TO A DRYWALL CEILING:

a. Drill a 1/8-in. pilot hole into each of the screw locations marked on the ceiling. You can also use an awl or nail to dimple the

screw holes.

b. Install a drywall anchor (BB) and a hook screw (CC) in each drilled mounting hole.

NOTE:

The drywall anchors (BB) are only to be used for mounting the ﬁxture to plaster or drywall surfaces

MOUNTING TO A WOOD CEILING:

a. Drill a 1/16 in. diameter pilot hole in the ceiling.

b. Tighten the hook screw (CC) into the wood.

B C

AA BB CC

888mm

34.96 in

Summary of content (8 pages)

PAGE 1
Item # 1005535874 Model # 55701141 Use and Care Guide 40in. Shop light with Motion Sensor Package Contents Part A B C D Description Shop Light Electrical Plug Adapter 5 ft. Power Cord / Linking Cable End-to-End Connector Quantity 1 1 1 1 A B C D Hardware Included Part AA BB CC DD Description Mounting Chain Drywall Anchor Hook Screw Cable Tie Quantity 2 2 2 1 AA BB CC DD NOTE: Keep your receipt and these instructions for proof of purchase. WARNING: RISK OF ELECTRIC SHOCK.
PAGE 2
AA 2. Attach the S hook at the bottom of the mounting chain (AA) to the hanger on the shop light (A). Repeat this step on the other side of the fixture. Then close all hooks with pliers to secure them. Hanger A 3. Hang the shop light (A) by placing one chain (AA) over each hook screw (CC) that has been installed on the ceiling. 4. Adjust chains to level light. The fixture must hang at least 3 in. from the ceiling. CC AA A 5.
PAGE 3
CONTINUOUS Installation Multiple light fixtures can be connected, up to a maximum of seven 40 in. shop lights or 266 total watts. Only the first light fixture needs to be plugged into an electrical outlet. 1. Remove the end cap from one end of each fixture body that will be linked. 2. Connect each additional fixture using either the linking cable (C) or end-to-end connector (D). When using the linking cable, the maximum distance between two light fixtures is 5 ft. 3.
PAGE 4
Care and Cleaning CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring. Troubleshooting Minor problems often can be fixed without the help of an electrician.
PAGE 5
Artículo # 1005535874 Modelo # 55701141 GUÍA DE USO Y CUIDADO LÁMPARA DE TALLER DE 40 PULG.
PAGE 6
2. Fije el gancho S en la parte inferior de la cadena de montaje (AA) a la percha en la lámpara de taller (A). Repita este paso en el otro lado del aparato. Luego cierre todos los ganchos con alicates para asegurarlos. AA Percha A 3. Cuelgue la lámpara de taller (A) colocando una cadena (AA) sobre cada gancho (CC) que se ha instalado en el techo. 4. Ajuste las cadenas para nivelar la lámpara. La lámpara debe colgar al menos 3 pulgadas del techo. CC AA A 5.
PAGE 7
INSTALACIÓN EN SERIE Se pueden conectar múltiples lámparas, hasta un máximo de siete lámparas de taller de 40 pulg. o 266 vatios totales. Solo la primera lámpara necesita ser conectada a una toma de corriente. 1. Retire el tapa del extremo de cada cuerpo de lámpara que se enlace. 2. Conecte cada lámpara adicional utilizando el cable de enlace (C) o el conector de extremo a extremo (D). Al usar el cable de enlace, la distancia máxima entre dos lámparas es de 5 pies. 3.
PAGE 8
Cuidado y limpieza PRECAUCIÓN: tes de limpiar la lámpara, desconecte el suministro eléctrico hacia ésta apagando el cortacircuitos o extrayendo el fusible de la caja de fusibles. Limpie la lámpara con un paño suave y seco. No utilice limpiadores con productos químicos, solventes o abrasivos. No use limpiador líquido en las bombillas LED, en la unidad LED ni en los cables que están dentro de la lámpara. Solución de problemas Los problemas menores pueden arreglarse sin ayuda de un electricista.