LIST INSTRUCTIONS-PARTS This manualcontains IMPORTANT INSTRUCTIONSand WARNINGS. READAND RETAINFOR REFERENCE. FLUID COMMANDER 0 l ORACO - Electronic Dispensing Control 120 VAC, 60 Hz, 0.
TYPICAL INSTALLATION KEY Dispensing Control Drain Sack Tube Pump Intake Vaive Supply Tank Air Shutoff Valve. Bleed type Air Filter Air Solenoid Valve, P/N 215-407 Air Regulator, P/N 202-156 Pump Pulse Meter. P/N 223-645 Pressure Relief IGI P/N 207-221, l-1/2 npt (m x f).%U psi Max WPR Fluid Shutoff Valve. P/N 108-458.
INSTALLATION ponents can withstand the pressures developed. The maximum fluid working pressure of the Fluid Commander System is 756 psi (52 bar). NEVER exceed the maximum working pressure of the lOWeSt rated accessory (valve, pipe, fitting, hose, etc.) in Mount the Fluid Commander The Fluid Commander can be placed on a desktop or mounted on a wall using the accessory wail bracket, pan no. 186-472. See Fig 1.
THREE FLUIDS TO FOUR STATIONS STATION FLUID SOLENOID VALVES FLUID1 FLUID2 ! FLUID3 ! , 1 FLUID SOLENOID GROlJNDl (postuons 13-16) = Station Numbers I AIR SOLENOID GROUND1 = + = RED - = BUCK FLU’D 2 I FLU’D 2 FLUID 3 ; FLUID 3 AIR SOLENOID VALVES PULSE UNITS STATION FWID SOLENOID VALVES I I FLUID 1 I I FLUID 2 FWID SOLENOID GROUND1 (posluons 13-M) StaU~n Numbers Y J AIR SOLENOID GROUND1 Y + = RED - = SLACK FLUID1 + FLUID 2 i FLUID1 I PULSE UNITS FLUID2 AIR SOLENOID VALVES STAT
OPERATION 1. Program the security code and set the units of measurement 5. To stop the dispense and check the Preset amount A four digit security code is required to activate the ContrOl afler turning It on. Thls prevents unauthorized use of the system. Press STOP/CLEARand then press and hold AMOUNT PRESETto verlfy the original order. Press DISPENSEto continue the order. me control is factory-set to dispense In quarts.
ACCESSORIES PULSE METER TECHNICAL DATA 223-645 For Gallon/Quart Pint E/ecfrksl Input Voltage . . . . . . . . . . . . Current Loop Output . . . . CAUTION To avoid damaging the electronic components of the pulse meter control (1) : 1. Do not lay anything on the eleCtrOniC . 15 V Maximum .4 milliamps OFF 10 milllamps ON Hydraulk Flow.. . . . . . . . . . . . . 12gpm Maximum (45.6 Lltedmin Maximum) Max. Operating Pressure . 1566 psi (105 bar) Inlet/Outlet. . . . . . . . . . . . l/2 npt controt. 2.
ACCESSORIES AIR SOLENOID VALVE 215-407 TECHNICAL DATA Type 3 way solenoid operated air valve, normally closed Electrical Rating . . . . . . . . . . . 24 V DC, 0.25 amps General purpose, Class A Coil Insulation . . Encapsulated - Continuous Duty Leads . . . . . . . . . . . . . . . . 16AWGx12.0ln.long . . . . . . . Adapted to l/2 npt Inlet/Outlet Wiring Gauge Required for LengthofRun . . . . . . . . . . 18AWGupto39Oft. 16AWGupto506ft. 14 AWG up to lOOOft. \ W IRING HARNESS 224-090 50 ft (15.2 m) long.
TECHNICAL DATA .... .. . . . . . 750 psi (52 bar) Fluid System Maximum Operating Pressure Powerlnput . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110/12Ovolt,6OHz Units of Measurement Totalizlng . . Gallons to 19999 Dispensing . . . . . . . . . . . . . . 0.01 increments up to 199.99 Pints, Quarts, or Gallons CircuitBreaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l.OAmp Power Supply Cord . . . . . . . . . . . . . .
308-036 9
THE GRACO WARRANTY AND DISCLAIMERS WARRANTY Gracowarrsnlsall equipment manufactured by it andbsarlng ilsnametobefrsefromdefscts in materialand workmanshi onlhedale of sale by an authorized Grace distributor lo the original purchaser for use. As purchaser’s sole remedy for breach oft it is warranty, Grace will, for a riod of twelve months from the dale of sale, repair or replace any part of the equipment proven defective. This warranty applies on p” y when the equipment is InsfaIled.
303-036 11
PROGRAMMING SECURITY CODE AND CHANGING MEASUREMENT UNITS I I For the Fluid Commander Dispensina Control I TEAR OUT THIS SHEET ALONG THE DOTTED LINE and keep it in a secure place after initiblly entering the security code and setting the measurement units. TO PROGRAMYOUR SECURITY CODE TO CHANGE~MEASUREMENT UNITS 1, Turn on the control. (Gallon, Quart or Pint only - controls measured In IlterS cannot be changed) 2.
