Model No.
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE. Thank you for choosing the COMFORT ZONE® Infrared Heating System. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.
17. Always unplug the unit before moving or cleaning, or whenever the heater is not in use. 18. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards. 19. Always use on a dry, level surface. Use on floor only. 20. DO NOT use outdoors. 21.
WARNING: This heater has a voltage rating of 120 volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding-type plugs to two-slot receptacles (B). The grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG.
Control Panel 1 15 2 14 13 3 4 12 11 10 9 8 7 6 5 1. Signal-receiving window: for receiving remote control signal. 2. Digital display：indicate set room temperature or time value of the timer. 3. Power indication Light: indicates when the unit is connected to power supply and rear master power switch is on. 4. ON/OFF switch button: for power-on or off. 5. Energy-saving mode：the light is on when energy-saving mode is set. 6. Mode button：for selecting the running mode. 7.
Remote Control Mode button: Used for mode selection Power Mode ON/OFF button: Used for power-on or power-off when master power switch on rear of unit is on Temp up button: to increase set temperature Temp. Up Temp down button: to reduce set temperature Temp. Down Timer button: used for setting timer and adjust time value of the timer Timer PREPARATION Place the heater on a firm, level surface and plug into a grounded 120V, 60Hz power outlet.
OPERATING INSTRUCTIONS 1. Start and select working mode With master power switch at the rear of the unit on, turn the heater on by pressing the ON/OFF button on the control panel or by pressing the Power button on the supplied remote control. Or Once power is off, heating elements will stop working at first. Fan will continue working for up to 3 minutes to emit residual heat inside the unit. Select a heat setting. Press the MODE button to toggle between the three heat settings.
3. Setting timer-power-off Note: ONLY under power-on mode can you set timer-power-off function. Or After starting the unit, press the timer button on the control panel. Digital display changes from set temperature to time value for the timer. Each press of the timer button will increase the timer length by 1 hour up to 12 hours. To cancel the timer, cycle through the lengths until the value is “00” The timer light is on when timer–power-off is set. 4.
MAINTENANCE 1. Turn off the master power switch in the rear of the unit. 2. Unplug the unit and let it cool completely. 3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquid enter the heater. 4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater.
STORAGE Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit. TROUBLESHOOTING If the heater will not operate, please check the following before seeking repair of service: 1. 2. 3. 4. Check if the power cord is plugged into an electrical outlet, if not, plug in. Check if electricity to the main fuse is working and the outlet has power. Be sure master power switch on the rear of the unit is on.
