4-8-16 INPUTS H264 STAND-ALONE DIGITAL VIDEO RECORDER ART.
Contents Chapter One Product Description ............................................................................................................ 2 1.1 General Description .................................................................................................................. 2 1.2 Technical Parameters ................................................................................................................. 2 1.3 Open Case And Connect Cable……………….……......................................
.9.3 System Log .................................................................................................................. 22 3.10 System Logout ....................................................................................................................... 22 ESEE user manual ……………..............................................................................................23 Chapter one Product Description 1.
Alarm Input 4 ch 4 ch 4 ch Alarm Output 1ch 1ch 1ch PTZ RS485 HardDisk 1 SATA 2 SATA 2 SATA Interface Network RJ45 10M/100M self-adaptive Ethernet interface USB Interface 2USB2.0 high-speed interface Power 12 VDC 1.3 Open Case And Connect Cables 1.3.1 Open-case inspection First of all, please check if there is apparent damage of the packing as soon as you received the products. The material can protect from the damage very well in the transportation.
Chapter Two: Structure Appearance Description 2.1 Panel Description 1. POWER led 9. PTZ: PTZ key 2. 1 ~ 4: CH1 ~ CH4 Single-Screen keys 10. ESC: Exit key 3. QUAD key 11. MENU: Menu key 4. State led, reserved 12. ▲▼◄►: Direction key 5. HDD led 13. 6. FN Switch 14. IR receiver 7. PLAY: Playback key 15. N.C. 8.
1. HDD led 9. PLAY: Playback key 2. State led, reserved 10. ESC: Exit key 3. 1 ~ 8: CH1 ~ CH8 Single-Screen keys 11. MENU: Menu key 4. ▲▼◄►: Direction key 12. 5. POWER led 13. N.C. : Confirm key 6. IR receiver 7. QUAD key 8. REC: Manual recording key 1. POWER led 9. ESC: Exit key 2. HDD led 10. MENU: Menu key 3. REC: Manual recording key 11. ▲▼◄►: Direction key, 4. FN key 12. N.C. 5. PLAY: Playback key 6. ON/OFF key 7. Multi-Screen key 8.
2.2 Product Interface Description 4 channels DVR Rear Panel 1. VIDEO IN: CH1 – CH4 video input 2. OUT V: analog video output 3. OUT A: audio output 4. AUDIO IN 1-2: audio input 5. VGA: VGA video output 6. ALARM: alarm input / output 7. POWER key 8. HDMI: HDMI video output 9. NET: RJ45 network interface 10. USB interface 11. RS485 12. DC12V power supply 8 channels DVR Rear Panel 1. VIDEO IN: CH1 – CH8 video input 2. OUT V: analog video output 3. OUT A: audio output 4.
7. POWER key 8. ALARM: alarm input / output 9. HDMI: HDMI video output 10. VGA: VGA video output 11. NET: RJ45 network interface 12. USB interface 13. RS485 14. DC12V power supply 15. Fan 2.3 Remote Control Description POWER Power switch DEV Device button: after press" DEV", input the same number as device number and press “ENTER” to save the setting.
the same number. Chapter Three: Description of Operation System 3.1 Turn ON / OFF Confirm that AC voltage accessible matches with DVR. Ensure that the DVR power outlet connect with a good middle ground grounding. After switching power, the device started, 【POWER】 light is on. Turn into system, if the panel status light flashing, it's normal conditions. 3.2 Preview After device start, preview interface can be seen immediately. In the preview interface you can see the system date, time, channel name.
b) After input the information, click 【OK】【CANCEL】 button or button【ESC】can safe or exit （5） Button: used to implement a specific function or enter the next setup menu, click【OK / 】 key and the left mouse button. 3.3.3 ESC MENU Press 【MENU】, 【ESC】 or the right mouse button to exit the menu mode Click the right mouse button and return to the previous menu level. 3.4 Main Menu Introduction Press MENU key or right mouse, it will pop-up the main menu.
3.5.1 Video Search Channel：to choose the target channel by clicking the check box. means selected, means non-selected Record mode：to choose the recode mode by clicking the check box. means selected, means non-selected Search time：input the Starting and finishing time into edit box Search：After setup the above search condition, click "search" to begin the corresponding video file searching and show the files. Red means time recording, green means MD recording, yellow means sensor recording.
Manual record menu include several parts: Channel：☑”means open; “□”means close. All on: start all the channel. All off: close all the channel. OK: confirm and exit Cancel: click cancel can exit the manual record interface and back to main menu. Remarks: the video which start by manual must be turned off by manual, otherwise the recording will be always continue. 3.7 PTZ control Choose the "PTZ control" from shortcut menu .
3.8.2 Video backup Choose the channel, and record mode; setup the search time, then begin search the file. After choosing the needed file from list box, click backup and ok, wait for process bar until 100% and show backup success. Note：USB driver pen must be FAT32 format when backup the file. 3.8.3 System setup In the setup menu, Choose “system setup” and turn into it's sub menu. It includes: General setup, Encode setup, Record setup, Network setup, Screen setup, Video detection, PTZ setup, Sensor setup.
3.8.3.1 General setup Choose the "General setup" and turn into it's setup interface. Time：DVR preview time. Click“refresh” after setting, it will pop out " the recording will stop once you modify the time", and save the setting. Date Format: Y/M/D”、“D/M/Y”、“M/D/Y” Auto Logout: DVR will log off if there is no operation within 10 minutes, it needs login again. Key Buzzer： Enable: there is sound with the controller or pressing key on front panel; Disable: without sound.
Select “encond setup” in system setup. Channel ：choose the right CH you need by clicking the select box Stream： choose the right stream you need : "main stream" or "sub stream " Encode mode：choose the right encode model you need : "video only "means only encoding for video ; "AV combined" means encoding for both video and audio. Bitrate mode ：choose the right bitrate mode you need : "constant bitrate " means system encoding video as user-defined bitrate and and frame rate.
Select “record setup” in system setup. Channel ：chose the target channel by clicking the select box Weekday : chose the correspond day as user's need, "ALL" means record all date. Recording mode and time：in the time edit box, user can set different time with different recoding mode . "Time " : in red color , "Motion": in green color , "Sensor": in yellow color ; “☑" means selected, “□” means invalid. There is times status display which 0~24 hours for whole schedule.
Data port: this port number is used for device and mobile visit ; suggest to set the port above 2000. NOTE: To view images of DVRs art. SDVR040A, SDVR080A and SDVR160A from smartphones (iOS or Android OS) please use the app "ESEENET+" which is freely downloadable from the relative stores (Apple Store and Play Store). The same app for smartphones has to be used for tablet devices. ESee： after connecting internet , click“☑ Esee” and save the setting, user will get an Esee ID.
Select “screen setup” from “system setup” menu Channel：chose the target channel by clicking select box. Camera title：user can edit the channel title from the edit box. “☑” means display channel title, “□”means non-display. OSD Alpha: user can adjusted the OSD menu transparency as needed. OSD time：“☑”display system time，“□” non- display; Auto Switch： user can setup the time of auto switching for preview image, it switch in single screen or 4 Channels screen.
Copy to ： select the channel and click "copy to" & ''ok " to copy the same setting to other channel. Or user can choose copy to "all" to make all channel in same stetting . Click button "cancel", the setup information will be non-saved but exit. 3.8.3.7 PTZ setup Select ”PTZ setup” from “system setup” menu Channel: chose the target channel by clicking select box Protocol: support Pelco-D and Pelco-P. Select the same protocol as PTZ.
In "system setup" menu , choose "PTZ setup" to enter it's setting interface. Channel：chose the target channel by clicking select box. Work mode: select disable or able to stop the alarm or start the alarm. Alarm duration: set up alarm duration time. Recording channel: select the target channel to make recording after alarm is triggered.
click" user management ". Add user: input a new user name in the edit box and set up the operational authority. Choose in the right check box, “☑” means the users can use it, “□” users cannot use it. Click the "set password " to set the new password, or it can be the default password.
In " management tool", click "system maintenance", enter setting interface Auto reboot: setting automatic reboot time, it can set" Saturday to Sunday" . "Never" means do not reboot automatically Firmware upgrade: copy firmware to the root USB disk, insert USB, select the USB storage device, then click "start" to upgrade. When upgrade is completed, click "OK" then system automatically reboot. Note: 1.Firmware name should be: FWHI1504A_***.rom(4ch), FWHI1508A_***.
info 3.9.1 HDD info The list box shows current HDD status info 3.9.2 System version Device name, device model, H/W version, S/W version could be checked here 3.9.
3.10 System logout In main menu, click "system logout", popup setting interface User logout: Logout current user. After logout, if you want to use the device again, need to login System reboot: It will reboot when click "OK" Esee User Manual 1. Connect DVR with network, make sure network working fine 2. Enter router to enable UPNP.As below picture, it is TP-LINK router. But for different router, UPnP might in different place, please find it, then enable 3.
IP address: Default 192.168.1.114 (User input correct IP according IP actual situation, if in 1 network segment, input 192.168.1.114, if in 0 network segment, input 192.168.0.114 ).If no IP conflict, do not need to change 114 to other IP Subnet mask: In order to distinguish subnet segment, default 255.255.255.0 Default gateway: Default 192.168.1.1 (Change according to actual situation). In router running status can see gateway DNS address: Default 192.168.1.1,change your network segment DNS.
1.
means select). In channel on/off table, click left mouse, can open or close that channel video, such as: on; off Preview mode: In preview mode switch table, can click to choose mode, or double click channel to signal channel preview mode, or switch to multi-channel mode. COMELIT DNS SERVICE For this series of DVR is now available the Comelit DNS service. To use it proceed as follows: 1 – check the firmware version of the device. The service is available from the version 1.8.3 dated 20140527.
27
