Quick User Guide Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelitgroup.com e-mail : export.department@comelit.
Image Model Description IPCAM720A Full HD Entry IP IR Plastic Dome Camera 3.7mm Fixed, 24 IR LEDs, H.264 & MPEG4 & MJPEG, SDHC, PoE/DC12V IPCAM700A Full HD Entry IP IR Bullet Camera 3.7mm Fixed, 24 IR LEDs, H.264& MPEG4 & MJPEG, SDHC, PoE/DC12V, IP66 IPCAM722A Full HD Entry IP IR Vandal Proof Dome Camera 3.7mm Fixed, 24 IR LEDs, H.264& MPEG4 & MJPEG , SDHC, PoE/DC12V, IP66 IPCAM702A Full HD Entry IP IR Bullet Camera 3.5-16mm Vari, 32 IR LEDs, H.
1. INSTALLATION 1 Hardware Connection Connecting to the Network Connect a standard RJ-45 cable to the network port of the Camera. Generally a cross-over cable is used for directly connection to PC, while a direct cable is used for connection to a hub/switch Micro SD memory slot Insert the Micro SD memory card up to 32GB.
Connecting the Power Connect the DC 12V power adaptor to the camera.
2 Network Connection (Zero Configuration Networking) IP cameras, NVR, and COMELIT RAS Solution support ZERO configuration. Installation is simple and convenient. No need any network setting. If there is no DHCP to assign the IP address, it will search the computer IP address or NVR which is running in the LAN. And then it will set the IP address automatically.
2 Network Connection (IP assignment) When a camera is connected without Zero configuration function to the network it has no IP address. So, it is necessary to allocate an IP address to the device with the “Smart Manager” utility on the CD. (Default IP 192.168.30.220) 1. Connect the camera to the network and power up. 2.
2. OPERATION The network camera can be used with Windows® operating system and browsers. The recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera™ and Google® Chrome® with Windows. ! Note: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX controls. 1 How to Access from a browser 1. Start a browser. 2. Enter the IP address or host name of the network camera in the Location/Address field of your browser. 3. You can see a starting page.
2 Resetting to the factory default settings To reset the Network Camera to the original factory settings, go to the Setup>System> Maintenance web page (described in User’s Manual, “System > Maintenance”) or use the Reset button on the network camera, as described below 1. Switch off the Network Camera by disconnecting the power adapter. 2. Press and hold the Reset button while reconnecting the power. 3. Keep the Reset button pressed during about 2 seconds or more than. 4. Release the Reset button. 5.
Reset Button [IPCAM722A] 1. Switch off the Network Camera by disconnecting the power adapter. 2. Press and hold the Reset button while reconnecting the power. 3. Keep the Reset button pressed during about 2 seconds or more than. 4. Release the Reset button. 5. The network camera resets to factory defaults and restarts after completing the factory reset. [IPCAM702A] 1. Switch off the Network Camera by disconnecting the power adapter. 2. Remove the front cap of the camera. 3.
1. Switch off the Network Camera by disconnecting the power adapter. 2. Press and hold the Reset button with a straightened paperclip while reconnecting the power. 3. Keep the Reset button pressed during about 2 seconds or more than. 4. Release the Reset button. 5. The network camera resets to factory defaults and restarts after completing the factory reset. Reset Button [IPCAM727A] Caution: When performing a Factory Reset, you will lose any settings you have saved. (Default IP 192.168.30.
Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelitgroup.com e-mail : export.department@comelit.
