Manual

E N G L I S H
GROUP S.p.A.
FT CT 05 4
WARNING
• Installtheequipmentbycarefullyfollowingtheinstructionsgivenbythemanufacturerandincompliancewiththestandardsinforce.
• Alltheequipmentmustonlybeusedforthepurposeitwasdesignedfor.Comelit Group S.p.A.declinesanyresponsibilityforimproperuseoftheapparatus,for
modicationsmadebythirdpartiesforanyreasonorpurpose,andfortheuseofnon-originalaccessoriesandmaterials.
• Alltheproductscomplywiththerequirementsofthe2006/95/CEdirectives(whichreplacedirective73/23/CEEandsubsequentamendments),ascertiedbythe
CEmarkontheproducts.
• Donotrouteriserwiresinproximitytopowersupplycables(230/400V).
• Installation,mountingandassistanceproceduresforelectricaldevicesmustonlybeperformedbyspecialisedelectricians.
TELEPHONE DIRECT CONNECTED TO COMELIT INTERFACE
Whenacallhasbeenmadethephonecanbeanswered.Nowyoucanspeakwiththevisitor.
Ifyouwanttoopenthedoor,press:
Thedoorwillbeopenedandtheconnectionwillbeterminatedinafewseconds.
Whenyoureceiveatelephonecallwhileincommunicationwiththevisitorabeepwillannounceyouthereisacall"behind"yourcurrentoperation.Youcananswerthiscalby
hang-upthereceiverandliftitwhenthetelephonerings.Youcandothesameifyouareinatelephoneconversationandavisitorisatthedoor.
OPTIONAL FUTURES:
A. TELEPHONE CONNECTED DIRECTLY TO THE COMELIT INTERFACE, ALONG WITH A COMELIT DOOR-ENTRY PHONE OR MONITOR
Thefirstreceiverusedtoansweracallfromadoor-entryphonewillbegincommunicatingwiththeexternalunit;youwillnotbeabletouseanyoftheotherreceiversto
answerthiscall.
B. STANDARD “FOLLOW-ME” FUNCTION USING A REMOTE TELEPHONE OR A MOBILE TELEPHONE
Onreceiptofacall,answerusingthetelephonetoautomaticallybegincommunicatingwiththevisitor.Ifyouwishtoopenthedoor,press**.Thedoorwillbeopenedand
communicationterminatedinthespaceofafewseconds.Insomemobilephones,the**commandisreservedforadifferentfunction;inthiscaseyouwillbeabletouse
#*toopenthedoor.
C. SPECIAL “FOLLOW-ME” FUNCTION USING A REMOTE TELEPHONE OR MOBILE TELEPHONE, WITH CALL WAITING FROM EXTERNAL UNIT
Theinstallermaysetupanalternative“Follow-me”operatingmode.Inthiscase,theinterfacewillswitchdirectlyto“Follow-me”modewhilethetelephonerings;youwillalso
beabletoanswerusinganydoor-entryphone,monitorortelephone.
Whenyouanswerusingthetelephonein“Follow-me”mode,3beepswillsoundevery3seconds.Pressbutton1tobegincommunicatingwiththevisitor;alternatively,press
0torejectthecall.
D. SPECIAL DOOR OPENING
Theinstallermaysetupaseconddooropeningprocedure.Inthiscaseitwillbepossibletoopenaseconddoorusingthetelephone,bymeansoftheon-boardrelayof
Art.2904.Door1,connectedtotheexternalunit,canbeopenedbypressing**or#*.Theotherdoorwillbeopenedatthesametimeasdoor1(default),orcanbeopened
independentlyusingjustthe#*command(seepoint5L).
Insomemobilephones,the**codeisreservedfordifferentuses;inthiscaseitispossibletouse#*only.
1. CONNECTING THE SYSTEM:
ConnecttheinterfacetotheSimplebussystemaccordingtothedrawingsonpage16,17,18.Theinterfaceisbydefaultsettoworkonasinglefamilyvideokit(address
Simplebus1).Iftheinterfacehasbeeninstalledinasinglefamilyvideokityoucanskiptheprogrammingmentionedinstep2.
2. PROGRAMMING THE SIMPLEBUS ADDRESS OF THE TELEPHONE INTERFACE IN 3 STEPS:
Important: An analogue telephone must be connected to the output of the telephone interface.
1Settheprogrammingdipswitchtotheposition"ON".
2Makeacallfromtheentrancepaneltothetelephoneinterface.Thelastnumberwillbestoredintheinterface.Waitatleastfor5secondsandpickupthereceiverofthe
analoguetelephoneanddial:
Hangupthephone.
3Settheprogrammingdipswitchtotheposition"1"toenterintothenormalmode.
3. PROGRAMMING THE FOLLOW- ME FUNCTION OF THE TELEPHONE INTERFACE IN 3 STEPS:
Iftheinterfaceisusedasaswitchbetweentheurbanlineandthetelephone,noprogrammingisneeded.Iftheuserwantsthefollow-mefunctionalitytoanexternallineora
PABX,itisnecessarytoprogramthefollow-mefunction:
Important: An analogue telephone must be connected to the output of the telephone interface.
1Settheprogrammingdipswitchtotheposition"ON".
2Pickupthereceiverofthetelephone,whichisconnecteddirectlytotheinterface,waitfortheconrmationbeepsanddial**followedbythenumber.Endthenumberwith**.
Example:Inordertoprogramexternalnumber06-12345678dial:
A confirmation beep appears.
Apausecanbecreatedbydiallinganextra##(waitaftereach#onaconrmationbeep).
3Settheprogrammingdipswitchtotheposition"1"toenterintothenormalmode.