I GB F D E CS 60 II Ed.
SUMMARY ON DELIVERY OF THE MACHINE .............................................................................................................................4 INTRODUCTION ..........................................................................................................................................................4 DATA FOR IDENTIFICATION .....................................................................................................................................4 TECHNICAL DATA .......
On delivery of the machine When the machine is delivered to the customer, an immediate check must be performed to censure all the material mentioned in the shipping documents have been received and also to check that the machine has not suffered any damage during transportation. If damage has occurred, get the shipping agent to verify immediately the amount and nature of the damage suffered and at the same time inform our claim department.
SYMBOLS Filter shaker Central broom rotation (automatic/manual traction) Side brush Horn Central broom Open book symbol. Points out to read manual before using the machine. ON/OFF (battery machine) Warning symbol Read with care all instructions with this symbol to ensure operator and machine safety.
PREPARATION OF THE MACHINE 1. UNPACKING THE MACHINE The machine is delivered packed on a pallet. To move it use a fork truck or a pulley block with sling. 2. REMOVING THE PACKAGE To remove the package proceed as follows: 1. Remove the fixing tapes. 2. Remove the metal staples at package base. 3. Take off the carton. Package size in cm: 135x93x130. Weight of packed machine without batteries: 170 kg 3.
PREPARATION OF THE MACHINE 4. BATTERIES ASSEMBLY AND CONNECTION (battery machine only) For the best mix of economy and usage we suggest fitting 2 x 12V 140Ah batteries. Before assembly, ensure the batteries are charged. Assembly instructions: 1. Remove the “on-off” key from the lock. 2. Open the bonnet of the machine. 3. Using a suitable lifting method, position the batteries correctly in the compartment observing the polarity as in the attached picture. 4.
PREPARATION OF THE MACHINE 8. BATTERY CHARGE LEVEL INDICATOR The battery charge level indicator is digital with 4 fixed positions and a blinking one. The numbers which appear on the display show the approximate charge level. 4 = maximum charge, 3 = charge 3/4, 2 = charge 2/4, 1 = charge 1/4, 0 = discharged batteries (blinking) ATTENTION: a few seconds after the meter reads “0” it will start blinking, the brush motor will then automatically switch off, having only the capacity to reach the charge point.
GENERAL SAFETY REGULATIONS The rules below must be followed carefully in order to avoid injury to the operator and damage to the machine. Read the labels carefully on the machine. Do not cover them for any reason and replace them immediately if damaged. The machine must only be used by authorized staff who have been instructed in its use. During the operation of the machine, pay attention to other people around you, especially children. Do not place any liquid containers on the machine.
OPERATING THE MACHINE WORKING POSITION The user operates while sitting, having manual lever and pedal controls on the instruments control board. INSTRUMENT BOARD CONTROL POSITION 1. 2. 3. 4. 5. 6. 7. 8. 2 3 5 4 Horn Central broom switch device (MAN/AUTO) Battery control indicator Key start Hour meter Gear way switch Thermal protection (brush motor breaker) Thermal protection (traction motor breaker) 6 1 7 8 LEVER BRAKE AND FLAP POSITION 1. Parking and service brake lever 2.
WORK WARNING Before to operate every type of work: 1. Make sure that the parking brake is released 2. Make sure that the suction opening knob is all inserted OPERATION CENTRAL BRUSH SWITCH 1. Push the brush motor switch in AUTO position. In this position the central brush starts to turn when the accelerator pedal is pressed. The stopping is automatically when the machine is stopped.
WORK MACHINE STARTING SWITCH 1. Turn the key in position 1 (clockwise direction). 2. Check that the batteries electric charge is enough to do the foreseen work. 4 = maximum charge, 3 = charge 3/4, 2 = charge 2/4, 1 = charge 1/4, 0 = discharged batteries (blinking) To avoid permanent damages to batteries, it’s essential to avoid the complete batteries discharge. When the meter reads “0” blinking on the display, the machine automatically switches off, having only the capacity to reach the charge point.
WORK BRAKE OR EMERGENCY BRAKE USAGE 1 Operating on the lever (1) you operate to brake or stop the machine speed. To stop completely the gear press and push back the pedal until it stops. To unblock the lever push forward and lift the foot. Block the brake lever in case of parking or parking on sloping surface. FLAP USAGE 1 Operating on the lever (1) you operate to open the flap. Push the pedal when there is bulky debris in order to allow its entry and collection into the central broom.
MAINTENANCE PROCEDURES WARNING ATTENTION! Before any adjustment and/or maintenance procedure always switch off the machine. ATTENTION! Disconnect the battery before starting any cleaning or maintenance procedure on the machine. CLEANING THE FILTER Once a week proceed with the cleaning of the filter operating as follows: 1. Switch off the machine 2. Remove the debris hopper 3. Disconnect the connector of the filter shaker (1) 4. Slightly loosen the 4 knobs (2) 5.
MAINTENANCE PROCEDURES ADJUSTMENT OF SIDE BRUSH The regulation of the brush pressure on the floor can be made by adjusting the screw behind the brush arm itself: 1. Loosen the lock nut (1). 2. Rotate the register screw counter clockwise until the bristles rest on the floor by about 2 cm. SIDE BRUSH REPLACEMENT 1. Unscrew the brush fixing knob. Remove the brush paying attention not to lose the washer and the knob. 2. Grease the shaft. 3. Insert the new brush by putting the key into its place.
TROUBLE SHOOTING GUIDE THE CENTRAL BROOM DOES NOT CLEAN 1. If the broom is worn or improperly positioned, adjust its position or if necessary have it replaced at your nearest COMAC S.p.A. service centre. 2. If the waste bin is full empty it. THE MACHINE CREATES AIRBORNE DUST IN USE 1. If the flaps that censure good suctions are torn replace them. 2. If the front flap is broken and the machine throws heavy dirty and waste forward, replace the front flap. 3.
BRUSH CHOICE AND USAGE POLYPROPYLENE BRUSH (PPL) It is used on any type of floores and it has a good resistance to wearing and to hot water (not over 60 degrees). PPL is not hygroscopic and so it keeps its features, also working on wet surfaces. ABRASIVE BRUSH The bristles are charged with very aggressive abrasives. It is used to clean very dirty floors. To avoid damages to the floor we suggest to work with the light necessary pressure. STEEL BRUSH The bristles are in steel threads.
