TABLET COMPUTER DR10 USER’S GUIDE
Notice Copyright© 2013, MilDef Crete Inc. All rights reserved. No part of this publication may be reproduced and modified without the written permission MilDef Crete Inc. MilDef Crete Inc. reserves the right to make changes in the products or the product specifications without any prior notice. Customers are advised to contact MilDef Crete Inc. for updated product information. MilDef Crete Inc.
Revision History: Revision Date 1.0.5 1.0.4 2015/01/22 2014/07/30 Changes Author Update weight info. Add Radiation exposure statement Pablo Tseng Pablo Tseng Add max. baud rate of COM port 1.0.3 1.0.2 2014/03/21 2013/12/30 1.0.1 1.0.0 2013/07/23 2013/06/25 Update Intel ME Driver Directory Update supported OS to Windows 7/8 Add operating & storage temp in spec Update drivers section, CE info, and button info.
FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class-B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20cm distance between the radiation & your body. Regulatory Information/Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product.
CE Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.
CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility Directive (2004/108/EC), Low-voltage Directive (2006/95/EC) and the procedures given in R&TTE Directive (1999/5/EC). The equipment was passed, and the equipment test was performed according to the following European standards: EN 300 328 V1.7.1 (2006) EN 301 893 V1.6.1 (2011) EN 301 489-1 V1.9.
Power Conservation This tablet computer consumes less power compared to conventional consumer computers. The power consumption may be further reduced by properly configuring the Power Management Setup. It is recommended that the power saving features be enabled even when not running on battery power. Power Management features can conserve power without degrading system performance.
Battery Precautions Only use batteries designed for this tablet computer. Using incompatible battery types may cause explosion, leakage or damage to the computer. Do not remove the battery from the computer while the computer is powered on. Do not continuously use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer is able to continuously work with a damaged battery, the circuit damage may occur and possibly cause fire.
Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials in accordance with local regulations at the end of the product's service life. Notice: The equipment may contain insignificant amount of hazardous substances for health and environment below control level.
TABLE OF CONTENTS CHAPTER 1 - GETTING STARTED .............................................................. 1 UNPACKING .................................................................................................................. 1 WORKPLACE ................................................................................................................. 2 ENVIRONMENTAL RATINGS ............................................................................................. 2 RUGGEDNESS ...................
PCH-IO CONFIGURATION SUB-MENU ........................................................................... 45 BOOT MENU ............................................................................................................... 47 BOOT MENU SELECTIONS ............................................................................................ 47 SECURITY MENU ......................................................................................................... 48 SAVE & EXIT MENU .....................
SECURITY ................................................................................................................... 65 DOCKLIGHT DL10 ....................................................................................................... 66 MULTI-BATTERY CHARGER DR..................................................................................... 66 EXTERNAL USB KEYBOARD ......................................................................................... 67 MINI KEYBOARD KBD ................
Getting Started Chapter 1 - Getting Started Unpacking The following components come with your computer. If anything is missing or damaged, please notify the dealer immediately.
Getting Started Workplace A clean and moisture-free environment is preferred. Make room for air circulation. Remember to avoid areas from: Sudden or extreme changes in temperature. Extreme heat. Strong electromagnetic fields (Near television set, motor rotation area, etc.). Dust or high humidity. If this tablet computer is required to work in a hostile environment, please maintain your tablet computer regularly by cleaning dust, water, and etc. to keep it in an optimal operating condition.
Getting Started Ruggedness The computer is designed with rugged features such as vibration, shock, dust, and rain/water protection. However, it is still necessary to provide appropriate protection while operating in harsh environments. NEVER immerse the computer in water. Doing so may cause permanent damages. Drop may cause parts break or permanent damages. The D-sub connector cap is for dust and shock protection only. The connector itself is sealed internally.
Getting Started Appearance Overview Note: The following illustrations show the tablet mounted on optional devices, which may not appear on your devices. Front ○,5 ○,1 ○,2 ○,4 ○,3 1. Touch Screen 2.
Getting Started Fn Key Plus (+) Sign Enter Key Left Arrow Key Decrease Brightness Right Arrow Key Increase Brightness 3. LED Indicators 4. Power Button 5. Optional Wi-Fi / Bluetooth Antenna For more information on Buttons and Indicators, please refer to Using Indicators and Buttons section. Rear ○,1 1.
Getting Started Left ○,1 ○,2 ○,3 ○,4 1. Battery 2. GLAN RJ45 3. USB 2.0 x 1 (Top) USB 2.0 with Fast Charger x 1 (Bottom) 4. Multi Bay: ExpressCard (Top) SIM Card + SD Card (Bottom) Note: SIM Card slot function requires optional WWAN module installed in your tablet computer. Right ○,1 ○,2 1. DC jack (2 pin for DR10I, 3 pin for DR10M) 2. Serial port DB9 (COM1, Default: RS232) Note: The External COM1 port default is RS232, and can be selected by BIOS (RS232/RS422/RS485).
Getting Started Top ○,1 ○,2 ○,3 1. Optional Wi-Fi Antenna 2. Optional GPS Antenna 3. Optional WWAN Antenna 4. 2.5” SATA II HDD / Optional SSD Bottom ○,1 1.
Getting Started Ready for Use After taking a quick look at your tablet computer, the following illustrations will get you ready for using it. 1. Mounting the Battery A. Mount the battery into the battery bay. B. Close the cover, turn clockwise and lock firmly with a flat-head screwdriver or a coin. B. Plug the AC cord into the AC 2. Connecting the AC Adapter A. Insert the DC Jack and firmly lock the connector clockwise. adapter. C. Plug the AC power plug into an electrical outlet.
Getting Started 3. Turning ON the Power A. Make sure the battery is securely mounted. Connect all power cords properly. B. Turn on the power of your tablet computer by pressing the “Power Button“. Press to turn on the power of your tablet computer. Note: The power is able to turn ON without any battery mounted once all the power cords are connected. 4. Turning Off the Power Directly tap “Shut down” from your OS to turn OFF the power of your tablet computer.
Operating Information Chapter2 - Operating Information Start Using Your Tablet Computer Always turn on your tablet computer by using the power button. This is the standard operating procedure to start using your tablet computer. After turning on the power of your tablet computer, it will start with the Operating System (OS) installed. Boot Up When you turn on the power, your computer will start to load the OS into the system memory. This start-up procedure is called “boot up”.
Operating Information Stop Using Your Tablet Computer Each time when you finish working with your tablet computer, there are several ways to stop your tablet computer from operating. Shut down Directly tap “Shut down” from your OS to turn OFF the power of your computer. Before shutting down, please do remember to save any unfinished works and close your applications to prevent your HDD from suffering possible data loss or damage. “Shut down” will turn OFF power of your computer.
Operating Information Working with Power Button (Heater Kit) Your tablet computer is equipped with a heater kit to enable work under low temperature. The heater will heat up the HDD to the temperature set by the user before booting the system. Also, the heater will constantly monitor HDD temperature. Once the temperature becomes lower, the heater will heat up again to maintain the temperature set by user.
Operating Information Installing Operating System Your computer is designed to operate with Microsoft Windows 7 or Windows 8 32 / 64-bit Operating System. Please connect your computer with an external USB-interface drive, such as an ODD or a USB thumb drive, and start the OS installation. Note: A USB hub may be required during installation to connect with an external USB-interface ODD and Keyboard, as the System USB port may not supply enough power.
Operating Information Some of the functions of the first layer buttons include: Button Layer 1 Description F1 Function Key F1/ BIOS General Help F2 Function Key F2 / BIOS Previous Values F3 Function Key F3 / BIOS Optimized Defaults F4 Function Key F4 / BIOS Save & Exit Tab Tabulation Minus (-) Sign BIOS change option Plus (+) Sign BIOS change option Left Arrow (←) Key BIOS Select screen Right Arrow (→) Key BIOS Select screen To perform 2nd layer combinational keystroke functions (keyst
Operating Information Using Hard Disk Drive (HDD) / Optional Solid State Drive (SSD) Your tablet is equipped with 2.5” SATA II Hard Disk Drive (HDD), or optional Solid State Drive (SSD) for data storage. HDD/SSD is user removable, providing convenience and security. It can ONLY be removed while power is OFF. Note: Avoid dropping your HDD/SSD module. Do not expose it directly to high temperature, high humidity, and other hazardous environment. NEVER try to disassemble the module.
Operating Information Using ExpressCards The computer supports 54 mm or 34 mm wide ExpressCard. You can install an ExpressCard while the computer is running. The computer automatically detects the card. To install an ExpressCard: - Hold the card with the top side of the card. - Slide the card into the slot until the card is completely seated in its connector. To remove an ExpressCard: Press the card and remove the card gently.
Operating Information Intel® Rapid Start Technology Your tablet computer can operate Intel® Rapid Start Technology when SSD is installed. This technology enables your system resume time not only to be as fast as wake-up time from S3 (Sleep) mode, but also to be more energy saving.
Operating Information Using the Touch Screen Your tablet computer is equipped with a highly sensitive touch screen, allowing you to navigate on the touch screen easily without using other external devices. Before using the touch screen, please follow the instructions below to calibrate your stylus pen for a more precise positioning: 1. Tap “Configure” to start. 2. Use “Standard Calibration” and follow the instructions.
Operating Information A stylus pen is provided for operating the touch screen. A list of operating tips is provided below to help you operate the touch screen more effectively with your stylus pen. Desired Operation Stylus Action Single Click Tap the touch screen once with your stylus pen. Double Click Quickly tap the touch screen twice with your stylus pen. Drag and Drop Right Click To drag, tap and hold the object gently with your stylus pen.
Operating Information Operating Wireless Devices For your ease of operations, you can turn on/off your wireless devices through the proprietary software application - “Device Power Manager”. Note: Depending on the configuration of your tablet computer, your Device Power Manager menu may appear differently from the screenshots provided in this section. When you adjust User Account Control (UAC), a security feature in Windows, the setting value of Device Power Manager will be affected.
Operating Information 2. Launch the Device Power Manager After launching the utility, please tap “Bluetooth” to enable the Bluetooth function (tap again to disable). Once the Bluetooth function starts up, the wireless LED indicator (color blue) will turn on and the Bluetooth icon will show up in the operating system accordingly. Tap “Bluetooth” to enable the Bluetooth function (tap again to disable).
Operating Information Wireless LAN (Option) Wireless LAN is an optional wireless communication module for your tablet computer. An embedded antenna will be pre-installed in your tablet computer to access the internet wirelessly. To activate your Wireless LAN function, please follow the illustrations below: 1. Driver & Application Installation a. Install the Chipset Driver first. Read from the Utility DVD and find the directory listed in the readme file to finish installation. b.
Operating Information Wireless Wide Area Network (Option) Wireless Wide Area Network (WWAN) is an optional module for your tablet computer. With pre-installed embedded antenna and the optional WWAN module, your tablet computer will be able to engage in WWAN functions. 1. Insert the SIM card a. Turn OFF your tablet computer. b. Pull down the rubber lock cover. c. Insert the SIM card into the SIM card slot.
Operating Information 2. Driver & Application Installation a. Please Install the WWAN driver first. For detailed instructions on installation procedures, please read from the Utility DVD and find the directory listed in the readme file. Follow the installation instructions to finish the driver installation. b. Install the Device Power Manager application. Read from the Utility DVD and find the directory listed in the readme file to finish installation.
Operating Information 1 3 2 4 1. Tap the Options first, and a User Options window will pop up. 2. Tap Firmware 3. Drop down the Network Operator list and choose an appropriate operator. If your operator is not on the list, please choose Generic UMTS. 4. Tap OK to complete the setting. Once the WWAN function starts up, the wireless device LED indicator will turn on (color blue). Note: You can find more setting information in Help Topics Chapter Two - 25 .
Operating Information GPS (Option) GPS is an optional module for your tablet computer. This GPS module supports both GPS and Galileo systems. An embedded antenna is pre-installed in your tablet computer to support the functions of your GPS. 1. Driver & Application Installation a. Install the Device Power Manager application: Read from the Utility DVD and find the directory listed in the readme file to finish installation. b.
Operating Information Note: Wireless devices can be turned ON/OFF through BIOS. Once a device is turned off through BIOS, its button on the Device Power Manager will be colored in yellow and with a prohibition marker. For example, the following illustration shows that WWAN and GPS devices are disabled through BIOS. To turn on, please enter into BIOS and enable the functions. For more information on BIOS setting, please refer to RF Device Control Configuration Sub-Menu section.
Operating Information Using Docklight DL10 (Option) Docklight acts as docking unit or port enhancer. It contains more ports that are not available on system unit. Mount Docklight 1. Open the rubber cap on the docking connector. 2. Align the docking connector. 3. Attach Docklight. 4. Fix the screws. Docklight ports Top 1. Docking connector Bottom and Left: 1 2 1. 2. 3. 4. 5. 6. 7. 8. 3 4 5 6 7 Audio jacks (Microphone/Speaker) RGB DB15 port Optional GLAN RJ45 Serial port (COM3: Default RS232) USB2.
Operating Information Note: The combination of DR10+DL8 or DR8+DL10.is not fully compatible. A few functions, including audio, modem, and surge protector, are incompatible in these combination.
Managing Power Chapter3- Managing Power AC Adapter The AC adapter performs two functions: - It powers the computer from an external AC source. - It charges the computer battery. The adapter automatically detects the AC line voltage (110V or 220V) and adjusts accordingly. The following are recommended when using the AC adapter: - Use a properly grounded AC outlet. - Use one AC outlet exclusively for the computer. Having other appliances on the same line may cause interference.
Managing Power Battery The computer will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: - Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). - Lower the intensity of the display by brightness control.
Managing Power Battery Gauge You may check battery status from battery gauge. Click the power/battery icon to reveal the battery gauge window. The following is the illustration of Battery Gauge in Windows OS. Note: Battery characteristic varies depending on factors such as ambient temperature, charging method, load current, aging, etc. For example, the chemicals of the battery are more inactive at low temperature, thus decreases the output power. The battery gauge should only be used as a reference.
Managing Power ACPI Support Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. With ACPI and an ACPI-compliant operating system (such as Microsoft Windows), this feature will allow you to reduce the power consumption and conserve energy. By supporting ACPI, the AC adapter LED and the Power indicator LED will show in different ways.
Managing Power USB Fast Charging Your tablet supports USB fast charging feature, enabling to quickly charge your fast-charging compatible devices. But note, fast charging is not supported in every power mode. The following table shows details for USB Charging information: Mode Power off Power on S3 USB 2.
Optional Devices BIOS Setup Chapter 4 - BIOS Setup Press [F2] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to “Exit” and press [Enter] then confirm save by pressing [Y].
Optional Devices BIOS Setup Advanced Menu Main Advanced Aptio Setup Utility Chipset Boot ► Trusted Computing ► SATA Configuration ► Intel (R) Rapid Start Technology ► USB Configuration ► IT8783F Super IO Configuration ► RF Device Control ► EC Thermal Control Security Trusted Setting →←: Save & Exit Computing Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup Advanced Menu Selections You can make the following selections on the Advanced Menu. Feature Options Description Trusted Computing Disabled Enabled TPM Support SATA Configuration SATA Mode Selection SATA Mode Selection: IDE, AHCI, Serial ATA Port 0 RAID Software Preserve Intel (R) Rapid Disabled Start Technology Enabled Enable or disable Intel (R) Rapid Start Technology. USB Configuration Legacy USB Support USB3.
Optional Devices BIOS Setup Trusted Computing Sub-Menu Aptio Setup Utility Advanced Configuration TPM SUPPORT Current Status Information SUPPORT TURNED OFF [Disable] Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup SATA Configuration Sub-Menu Aptio Setup Utility Advanced Determine how SATA controller(s) operate. SATA Mode Selection [AHCI] Serial ATA Port 0 Software Preserve Serial ATA Port 1 Software Preserve Serial ATA Port 2 Software Preserve Empty Unknown Empty Unknown SATA SSD (120.0 SUPPORTED →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup Intel (R) Rapid Start Technology Sub-Menu Aptio Setup Utility Advanced Intel (R) Rapid Start Technology [Disabled] Enables or disable Intel (R) Rapid Start Technology →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup USB Configuration Sub-Menu Aptio Setup Utility Advanced Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications USB Configuration USB Devices: 1 point Legacy USB Support USB3.0 Support XHCI Hand-off EHCI Hand-off [Enabled] [Enabled] [Enabled] [Disabled] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup IT8783F Super IO Configuration Sub-Menu Aptio Setup Utility Advanced Set Parameters of Serial Port 0 (COMA) IT8783F Super IO configuration IT8783F Super IO Chip ►Serial Port 0 Configuration IT8783F →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup RF Device Control Configuration Sub-Menu Aptio Setup Utility Advanced RF Device Control Setting RF Device Control GSM STATUS GSM GPS STATUS GPS BT STATUS BLUETOOTH WLAN STATUS WLAN Present [Enabled] Present [Enabled] Present [Enabled] Present [Enabled] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup EC Thermal Control Sub-Menu Aptio Setup Utility Advanced EC Thermal Control Thermal cooling trip point EC Thermal Control Setting [87 C] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup Chipset Menu Main Aptio Setup Utility Chipset Boot Advanced Security Save & Exit System Agent Parameters ► System Agent (SA) Configuration ► PCH-IO Configuration (SA) →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Chipset Menu Selections You can make the following selections on the Chipset sub-menu.
Optional Devices BIOS Setup PCH-IO Configuration Sub-Menu Selections You can make the following selections on the PCH-IO Configuration sub-menu. Feature Options Description PCH LAN Controller Disabled Enabled Enable or disable onboard NIC.
Optional Devices BIOS Setup Boot Menu Main Advanced Aptio Setup Utility Chipset Boot Boot Option Priorities Boot Option #1 [P2: SATA SSD...] Boot Option #2 [IBA GE Slot 00C8 v...] Network Device BBS Priorities Hard Driver BBS Priorities Security Save & Exit Sets the order system boot →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices BIOS Setup Security Menu Main Aptio Setup Utility Chipset Boot Advanced Security Save & Exit Set Password Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
Optional Devices BIOS Setup Save & Exit Menu Main Advanced Aptio Setup Utility Chipset Boot Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override P2: SATA SSD IBA GE Slot 00C8 v1365 Realtek PXE B01 D00 Security Save & Exit Exit system setup after saving the changes →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Optional Devices Drivers and Applications Chapter 5 – Drivers and Applications The Utility DVD includes all the drivers for the installed devices in your tablet computer. Please consult the dealer if there is any driver missing. Also, through Device Manager in Windows, you are able to perform “Driver Update” or check if there are still drivers for the devices needed to be installed. Please check the readme file on Utility DVD to get the latest information before installing device drivers.
Optional Devices Drivers and Applications VGA Windows 7/Ultimate 64-bit: Run "win64_15288.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Intel_VGA", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "win64_15288.exe" in the directory of "\Drivers\Windows 7 (32-bit)\Intel_VGA", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "win64_152812.
Optional Devices Drivers and Applications Intel ME Windows 7/Ultimate 64-bit: Run "Setup.exe" in the directory of " \Drivers\Windows 7 (64-bit)\Intel_ME\ME_SW_7.1.85.1216", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\Intel_ME\ME_SW_7.1.85.1216", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of " \Drivers\Windows 8 (64-bit)\Intel_ME\ME_SW_7.1.85.
Optional Devices Drivers and Applications Wireless Power Manager Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\0107\", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Utilities\0107\", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\0620\", and then follow the instructions to install. Windows 8/Ultimate 32-bit: Run "setup.
Optional Devices Drivers and Applications USB3.0 Windows 7/Ultimate 64-bit: Run "Texas Instruments xHCI Driver v1.12.25 ( Multilanguaje - WHQL ).exe" in the directory of "\Drivers\Windows 7 (64-bit)\USB3.0\Texas Instruments xHCI Driver v1.12.25 ( Multilanguaje - WHQL )", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "Texas Instruments xHCI Driver v1.12.25 ( Multilanguaje - WHQL ).exe" in the directory of "\Drivers\Windows 7 (32-bit)\USB3.0\Texas Instruments xHCI Driver v1.12.
Optional Devices Drivers and Applications Turbo Boost Monitor Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\IntelR Turbo Boost Technology Monitor", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\IntelR Turbo Boost Technology Monitor", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "setup.
Optional Devices Drivers and Applications 2nd Gigabit LAN (Option) Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\RTL8111E\Install_Win7_7046_07202011", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\RTL8111E\Install_Win7_7046_07202011", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "setup.
Optional Devices Drivers and Applications WiFi (Option) Windows 7/Ultimate 64-bit: Run "Wireless_15.3.1_Ds64.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Intel_WiFi6235\WLAN\64bit", and then follow the instructions to install. *: Then into the“Wireless Power Manager”to turn on the WLAN device. Windows 7/Ultimate 32-bit: Run "Wireless_15.3.1_Ds32.exe" in the directory of "\Drivers\Windows 7 (32-bit)\Intel_WiFi6235\WLAN\32bit", and then follow the instructions to install.
Optional Devices Drivers and Applications GPS (Option) Windows 7/Ultimate 64-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ublox_A4_U5_USB_drv3264_install_UI.exe" in the directory of "\Drivers\Windows 7 (64-bit)\UBlox 6H Driver", and then follow the instructions to install. Windows 7/Ultimate 32-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ublox_A4_U5_USB_drv3264_install_UI.
Optional Devices Drivers and Applications WWAN (Option) Windows 7/Ultimate 64-bit: *: First into the“Wireless Power Manager”to turn on the WWAN device. Install Driver: Run "SWIGobi3kSetup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\AirPrime MC8305 HSPA module (Gobi)\GenericGobi3k", and then follow the instructions to install. Install MC8305 module AP: Run "Watcher_Generic_Q.
Optional Devices Drivers and Applications TPM (Option) Windows 7/Ultimate 64-bit: *: First into the "BIOS" to turn on the TPM device. Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\TPM", and then follow the instructions to install. Windows 7/Ultimate 32-bit: *: First into the "BIOS" to turn on the TPM device. Run "setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\TPM", and then follow the instructions to install.
Specifications Chapter 6 – Specifications Platform Intel® Huron River Platform CPU Intel® Sandy Bridge i7-2610UE 4 MB Intel Smart Cache Memory PCH Intel® Cougar Point QM67 Memory Max. 8GB System Memory Industrial grade DDR3 SO-DIMM x 1, 1333MHz Touch Screen Type: 8.4” XGA LCD with LED B/L Resolution: 1024 x 768 pixels Brightness (min.~ typ.): 400 nits ~ 500 nits Single touch resistive type Sunlight readable Hard Disk Drive (HDD)/ Optional Solid State Drive (SSD) Type: Interface: 2.
Specifications I/O Ports - - - Serial port DB9 (Default RS232) GLAN RJ45 Multi Bay: • ExpressCard slot (ExpressCard/54) x 1(Top) • SIM Card slot x 1 + SD Card slot x 1(Bottom) Docking connector x 1 USB 2.0 ports : • USB 2.0 port x 1 (Top) • USB 2.0 with Fast Charger port x1 (Bottom) DC power jack Note: WOR (Wake On Ring) is provided only on COM1. The bottom USB port supports Fast Charging, where the icon on rubber cap has a lightening mark: .
Specifications Power Primary Battery: Type: Capacity: Dimensions: Weight: 6 x 18650 cells Lithium Ion 10.8V/ 5800mAh 149 mm (W) x 57.4 mm (D) x 20.5 mm (H) 300 g (0.65 1b.) Optional 2nd Battery: Type: 9 x 18650 cells Lithium Ion Capacity: 11.1V/ 7200mAh Dimensions: 150 mm (W) x 90 mm (D) x 20 mm (H) Weight: 500 g (1.1 lb.) AC Adapter Input Voltage: Frequency: Output Voltage: Maximum Power: Dimensions: Weight: AC 100 - 240V 50/60 Hz DC 19V 90 Watts 133 mm (W) x 58mm (D) x 30mm (H) 400 g (0.88 lb.
Specifications Operating & Storage Temperature Operating Temp.: I: 0 °C~+40 °C M: -20 °C~+50 °C* (*HDD: with heater; SSD: Industrial grade) Storage Temp.
Optional Devices Chapter 7 – Optional Devices Communication WiFi/Bluetooth: - Intel® Centrino® Advanced-N 6235, Dual Band - Board Form Factor: PCIe Half Mini Card - Wi-Fi Certified: 802.11 b/g/n - Bluetooth: Supports BT 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.
Optional Devices Docklight DL10 The Docklight can attach to computer or stand unit for mobile or stationary operation. Ports: Serial x 2, USB2.0 x 4, RGB, Audio (speaker out, microphone in), DC jack, Optional Giga LAN RJ45 x 1 Dimensions: 250mm (W) x 37mm (D) x 61mm (H) Weight: 0.45Kg (1 lb.) approximately DC input: 12~32V Environmental & Certifications: CE, FCC, IP54 Note: Serial ports: COM2/COM3 default RS232 USB Ports: 2 standard and 2 proprietary environmentally sealed USB jacks.
Optional Devices External USB Keyboard An optional 89-key external USB keyboard with LED backlight and IP rating of IP54 is available for your tablet computer. The detailed specification is provided below: 89-key layout emulates 101/102-key KB Life: >1 million times, water/dust protection up to IP54 Back-light illumination (backlight device: green LED) PS/2 compatible Trackpoint and mouse buttons Dimensions: 323.4 mm (W) x 172 mm (D) x 25 mm (H) Weight: 1.
Optional Devices Mini Keyboard KBD Mini Keyboard KBD is designed for all models. KBD also brings convenience of use through multi-language keyboard versions and USB interface. The detailed specification is provided below: USB interface with 30 cm USB cable 66-Key design with function keys to simulate standard keyboards. StickPointer to simulate mouse and keypad Currently support versions: English (UI), English (UK), German (DE), Swedish (SV) and Russian (RU) 5 versions.
Optional Devices Stand Unit Stand unit can hold the system unit and Docklight with adjustable view angle. It can be used in office or in vehicle. There are 2 configuration options: - Stand unit only to accept system unit. - Stand unit with Docklight hooked to accept system unit. Mount Stand Unit 1. Open the rubber cap on the docking connector. 2. Align the computer into stand unit. 3. Push the lever to engage and fix. 4. Lock the computer.
Maintenance and Service Chapter 8 – Maintenance and Service Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lint-free cloth. If there is difficulty removing dirt, apply non-ammonia, non-alcohol based glass cleaner to the cloth and wipe. An air gun is recommended for cleaning water and dust. For salty water please clean with fresh water then blow-dry with an air gun.
Maintenance and Service RMA Service If troubleshooting solutions are unsuccessful, consult your dealer for RMA. Shipping instructions: 1. Remove any personal add-on devices or other media. 2. Use the original shipping container and packing materials, if possible. 3. If the original packing materials are not available, wrap the equipment with soft material (e.g. PU/PE form) then put the wrapped equipment into a hard cardboard shipping box. 4.
