COLZER Dehumidifier User Manual Model No.: PD123A,PD223A Please read this User Manual before operating and keep safe for future reference.
BEFORE FIRST USE: To prevent any internal damage, it is very important to keep refrigeration products (like this dehumidifier) upright throughout their journey. Please leave it standing upright and outside the box for 24 HOURS before plugging it in.
Welcome Thanks for choosing us! COLZER is dedicated to keeping people healthy, comfortable and more enjoyable by offering quality appliances range from dehumidifiers, air purifiers, humidifiers to refrigerators, wine coolers, ice makers, and more. From breathing easier in your office to upgrading your kitchen appliances, we hope you trust COLZER to help you every step of the way. We do hope you’ll enjoy the dehumidifier you purchased from us.
CONTENTS SAFETY INFORMATION....................................................................................................................................................................... 1 PARTS IDENTIFICATION..................................................................................................................................................................... 2 CONTROL PANEL IDENTIFICATIONS..................................................................................................
『SAFETY INFORMATION』 To prevent injury to the user or other people and property damage, the following instructions must be followed when using the dehumidifier. 1. Install the dehumidifier properly on a floor, table, or shelf that is level and strong enough to support it when the water bucket is full. 2. Do not place the dehumidifier near a heater. 3. Do not use the dehumidifier near flammable gas or combustibles, such as gasoline, benzene, thinner, etc. 4. Always plug into a grounded outlet properly. 5.
『PARTS IDENTIFICATION』 NOTE: DO NOT OBSTRUCT THE AIR INLET AND/OR OUTLET.
『CONTROL PANEL IDENTIFICATIONS』 1. Understand the Top Control Panel The top control panel features a digital display and 6 buttons. 1) Understand the Control Buttons POWER Button: Press to turn the dehumidifier ON or OFF. Mode Button: Press to switch the working mode between DH (DEHUMIDIFY) mode and DRY (Laundry Dry) mode.
HUMIDITY Button: Press the HUMIDITY button repeatedly to adjust the set-point of humidity level between 30%-80% (in 5% increments) during normal DEHUMIDIFY (DH) mode. The digital number on the display will flash when changes are being made. NOTE: The HUMIDITY button will be disabled in the DRY-CLOTHES (DRY) mode. SPEED Button: Press the SPEED button to set the fan speed to FAST or SLOW in the normal DEHUMIDIFY (DH) mode. NOTE: The SPEED button will be disabled in the DRY-CLOTHES (DRY) mode.
DH: The “DH” icon will light up when the normal DEHUMIDIFY mode has been selected. 2. Understand the Front Display The front display displays the same content, like humidity readout or error codes, as the digital display on the top control panel. So you can read the room humidity level on the front display easily, in a visible distance. 『OPERATION INSTRUACTIONS』 1.
Uncoil the power cord and plug it firmly into a properly grounded 110-120 volt AC outlet. After plugged in, the control panel will be light up for 1-2 seconds and then goes off, which is the normal self-diagnose process and does not require any user intervention. 3. Turn the Dehumidifier On Press the POWER button to turn the dehumidifier on. Typically, the dehumidifier will run in the default setting of 30% set humidity at low fan speed in the normal DEHUMIDIFY mode.
the digital number turns to statically display the actual room humidity, during which time the setting will be automatically registered. · Let the Dehumidifier Run. The dehumidifier will automatically stop when the room humidity reaches the target RH% or when the water bucket is full. ★ You can also use the SPEED button to change the fan speed to FAST or SLOW. When the fan speed was set to high, the “FAST” icon will light up. When the fan speed was set to low, the “SLOW” icon will light up.
Note: · For the AUTO ON setting, please turn on the dehumidifier to select a desired humidity level. Otherwise, the humidity maintained will be the same as the previous setting. · You can only set AUTO ON timer when the dehumidifier is off or set AUTO OFF timer when the dehumidifier is on, but not be able to set both AUTO ON and AUTO OFF timer at the same time. · The TIMER feature is one-shot. So The TIMER will ONLY function one time instead of cycling the dehumidifier on or off indefinitely.
· Gently remove the water bucket from the dehumidifier by gripping both top and bottom sides and pulling outward; · Open the drain outlet lid on the bucket cover and then empty the bucket; · Replace the water bucket to the dehumidifier. The dehumidifier will auto eliminate the E7 error and resume operation in 1-3 minutes after the water bucket been replaced properly. 2) Continuous Drain by Gravity Water can be automatically be emptied into a floor drain by attaching the included drain hose.
since there is one end slightly smaller than another end. - Be sure to run the water hose sloping downward to let the water flow out smoothly. No kinks or bent. - Do not submerge the other end of the hose into the water. - It is recommended to use a short hose. If the drain hose is too long, water may not drain completely, which can lead to stagnant water and mildew build up inside the hose. - When the continuous drain feature is not being used, remove the drain hose from the outlet. 7.
『MAINTENANCE』 To avoid possible electric shock, ensure to turn the dehumidifier off and disconnect the plug from the power source before performing any cleaning or maintenance. 1. Clean the Vent and Case · Use water and mild detergent. Do not use bleach or abrasives. · Do not splash water directly onto the main dehumidifier. Doing so may cause an electric shock or the insulation to deteriorate, or cause the dehumidifier to rust.
4. When Not Using dehumidifier for Long Periods of Time · Operate the dehumidifier on high fan mode for half a day, and then wait 1 day before emptying the reservoir. · Clean the main dehumidifier, water reservoir, and air filter. Ensure the whole dehumidifier is clean and dry. · Wrap the cord and bundle it. · Cover the dehumidifier with a plastic bag. · Store the dehumidifier upright in a dry, well-ventilated place.
『SPECIFICATION』 Model PD123A PD223A Power Source 110-120V, 60Hz 110-120V, 60Hz 30 Pints/Day 70 Pints/Day 28 Pints/Day 51 Pints/Day 13 Pints/Day 30 Pints/Day Humidity Removal (95°F, 90%) Humidity Removal (86°F, 80%) Humidity Removal (80°F, 60%) 18 Pints/Day Humidity Removal (65°F, 60%) Wattage (95°F, 90%) Wattage (86°F, 80%) Wattage (80°F, 60%) 250W 460W 210W 360W 185W 260W Wattage (65°F, 60%) Airflow Rate 112 CFM, 190 CMH 112 CFM, 190 CMH Refrigerant R134a/5.6 oz R134a/8.
『TROUBLE SHOOTING』 1. Error Codes Error Code E1 Problem Humidity Sensor Malfunction E2 Defrost Temperature Sensor Malfunction E4 Ambient Temperature Sensor Malfunction E7 Solution 1. Check the humidity sensor and ensure it is in good condition. 2. Replace the humidity sensor. 1. Check the temperature sensor and ensure it is in good condition. 2. Replace the temperature sensor. 1. Check the temperature sensor and ensure it is in good condition. 2. Replace the humidity sensor. Empty the water bucket.
Problem Possible Causes Solutions Dehumidifier can not turn on The power cord is unplugged. Plug it in. The fuse is blown or circuit breaker is tripped. The water bucket is full or not in the proper position. Check the fuse or the circuit breaker. Make sure the water bucket is empty and has been installed properly. The room humidity has reached the set-point and the dehumidifier enters into Standby Mode where you can see the Mode icon (DH or DRY) flickering.
『WARRANTY』 COLZER offers a limited 1-year free warranty on this dehumidifier PD123A/PD223A, with original proof of purchase (typically you maybe only requested to offer the order number instead of an invoice) and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period.