User's Guide

ManualsBrandsCOLOROCK ManualsElectronicsSmart Switch (Breaker)

Table Of Contents

页 1

WiFi Smart Switch

lnp ut

Output

WiFi Smart Switch

Parameter:

Power supply: 90V~250V AC

Max: Current: 90V~250V AC

WiFi: Standard: 2. 4GHz b/g/n

Material: ABS VO

Size: 88*38*22mm

checklist:before using the device

Your smart phone or tablet has

connected to a 2. 4G WiFi with

internet

Your have the correct WiFi PWD

Your smart phone or tablet must

have access to APP Store, Google

play.

Your router is MAC-open

Router

Internet

Server

APP

WiFi

WiFi /G PRS

Android

IOS

account.

Power up.

ON/OFF operating principle

The connected appliances work/stop

through live wire power on/off.

If you have Intelligent life

account just log in.

App Store

AVAIL ABLE ON THE

User Guide

Start with"Smart Life"APP.

4.1 Appliance wiring instruction.

Input

90-250V

4. 2 Celling lamp wiring instruction.

4. 3 One wire wiring instruction.

Note: The ONOFF switch must be

powered up by N and L wires.

Press and hold the button for

about 5 seconds until the WiFi

LED blinks fast.

Cover

Pairing Button

Manuals witch

Enter the App,tap"+"in the

upper right of the page to enter

network connection page.

There are two network

connection methods(Normal

mode and AP mode). Normal

mode is default. Users could tap

the upper right corner to switch

the connection method to AP

mode.

please make sure the device's

indicator light rapidly flashes(2

times per second),tap to go on

to the next step

Input your WiFi password.

Name your device.

the device is online.

If indicator light is not rapidly

flashing,tap"how to set indicator

light as rapid flashes"to view

operation processes

Smart Switch

This instruction include the “RF

433MHz remote control”. according

to product you have.

WIFI L ED: BLUE

ON/O FF LE D： BLUE

RF con tro l ： RED。

RF 433MHz remote control

setting (if).

The RF LED is red.

1.Clear function

After push the receiver's learning

button 8 times,the receiver Clear

all the remote control data in it's

memory.When the LED flashes for

for the few times,it indicates that the

clear funchion is completed.(After

cleared the code in the receiver,all

the remote control must study from

receiver onece again to restart.)

2.About receiver's Working Mode

a)Momentary mode

Press the Remote control button,the

receiver's ralay is ON,release button

the receiver's relay is off.

b)Toggle mode

Press Remote control button for 1 time

the receiver's relay is on ;Press button

again,the receiver's relay is OFF.

c)Latched mode

Press Remote control button A,the

receiver's relay is ON,Press the

transmitter's button B,the receiver's

relay is OFF

3.Receiver operating mode settings

a)Setting momentary Mode

Press the receiver's Learning button 2

times,The receiver's RF LED will be lights

up red,it comes into Setting state,Press

the remote's button,the receiver's LED

will be flash red twice then come off,

Setting successfully.

b)Setting Toggle Mode

Press the receiver's Learning button 3

times, The receiver's RF LED will be lights

up red,it comes into Setting state,Press

the remote's button,the receiver's LED

c)Setting Latched Mode

(Note:When you choose＂Latched Mode＂

Press the receiver's Learning button 4 times,

The receiver's RF LED will be lights up red,it

comes into Setting state.Press the remote's

button A,the receiver's RF LED will be flash

red twice and lights up;Then press the

remote's button B, the receiver's RF LED

will be flash red twice and come off. Setting

successfully.

4.Note:

a)If the RF remote control's button was

learned,the receiver's RF red LED will

not be flash.now need to Clear function,

and learn the again.

b)every receiver just can learn Ten remote's

buttons.if you will delete the remote's

buttons,you can push the receiver's learning

button 8 times,the receiver Clear all the

remote control data in it's memory,and

learn the again.

will be flash red twice then come off,

Setting successfully.

you need to setting two different buttons

on the Remote Control,the first time learn

is for “ON”,the second time learn for “OFF”

For Example:Button A=ON,Button B=OFF)

TROUBLESHOOTING

Q: How to set indicator light as rapid

flashing?

① Power on device.power off after10s

and then power on.

②hold the reset button for 5s.

③ Confirm indicator light is now rapidly flahsing.

Q: How to set indicator light as slow flashing?

① Power on device.power off after

10s and then power on.

② hold the reset button for 5s.

③ Confirm indicator light is now rapidly

flahsing.

④ Hold reset button for 5s until indicator

light is slowly flashing.

The new added device needs 1min to

connect to WiFi and the Internet if it

stays offline for a long time please

judge the problem by the WiFi LED

status.

WiFi LED quickly blinks one time every

second;Sonoff failed to connect to your

WiFi

① Maybe you have entered wrong WiFi

password.

②Sonff is too far away from your WiFi

please take it closer.

③Make sure your router is MAC－open.

if still failed,try to open a mobile hot

apot and add again.

WiFi Smart Switch

lnput

Output

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnp ut

Output

APP

WiFi

WiFi /手机流

量

90-250V

交流电

保护盖

通断器

本说明书包含RF 433MHz遥控

功能的介绍，请依据实物确认是否

有此功能。

产品参数：

输入电压：90V~250V AC

量大功率：90V~250V AC

WiFi标准：2.4GHz b/g/n

外壳材质：ABS V0

尺寸规格：88*38*22mm

使用该设备前请检查以下事项

您的智能手机或平板已连接一

个能上网的2.4G WiFi

使用安卓系统的手机平板，系统

必须是4.0以上版本

使用苹果手机或ipaid必须能够

访问APP商店并下载APP

如果您的无线路由器设置了MAC

地址过滤，请先进入路由器后关闭

MAC地址过滤功能

路由器

互联网

云服务器

苹果、安卓手机

智能通断器

产品使用说明书

在各大市场下载智能生活APP.

安装过程如有提示权限请求选允许。

注册账号并登录智能生活。

按照外壳指示正确接线，本开关

必须零火线供电，严禁带电安装。

注：本设备的开关原理是通过控制

电路火线的通断从而实现电器工作

和停止，本设备必须零火线供电设

备才能正常工作。

免费下载智能生活APP.

4. 1 控制电器电路正确接线示意图。

4. 2 控制LED吸顶灯正确接线示意图。

4. 3 单火线输出正确接线示意图。

注意：本设备必须零火线接入才

能正常使用，且零火线不要接反

零线

火线

零线

火线

零线

火线

完成接线后通电，设备默认为关

闭，可以在APP更改设置为默认

开启。

进入应用程序，点击“＋”在页

面右上角进入网络连接页面。

有两种网络连接方法（普通模式

和AP模式）. 普通模式是默认的.

用户可以点击右上角，将连接方

法切换到AP模式。

在正常模式下，请确保设备指示

灯快速闪烁（每秒2次），点击

进入下一步。

如果指示灯不是快速闪烁，点

击“如何设置指示灯为快速闪

烁”查看操作过程。如何将指

示灯设置为快速闪烁。

配置按钮/手动开关

WIFI指示灯：蓝色

开关指示灯：蓝色

RF cont rol 指示灯：红色

输入手机当前连接的WIFI密码。

给设备命名，完成添加。

可进行远程遥控。

RF 433MHz 遥控使用说明（如有

此功能）.

Rf指示灯是红色的。

清除已学习按键

按通断器按键8次，红色指示灯闪烁然

后熄灭，表示已清除所有RF遥控器配

对按键。(当清除完成后，所有RF遥控

器按键需要重新学习才能使用。)

Rf遥控操作时，通断器工作模

式解释

a)点动模式

保持按下遥控器按键，通断器接通，

放开遥控器按键，通断器断开。

b)自锁模式

按一下遥控器按键1次，通断器切换

状态一次。比如当前为接通，按一次

遥控器按键，通断器断开。当前为断

开，按一次遥控器按键，通断器接通。

c)互锁模式

按一下遥控器A按键，通断器接通，

按一下遥控器B按键，通断器断开。

RF 遥控操作时，通断器工作

模式设置

a)设置点动模式：

按下通断器按键2次，通断器RF红色

指示灯亮起，在红灯亮起期间，按下

遥控器按键，红灯闪烁两次，然后熄

灭，此时此遥控器按键为点动模式。

b)设置自锁模式

按下通断器按键3次。通断器RF红色

指示灯亮起，在红灯亮起期间，按下

遥控器新的按键，红灯闪烁两次，然

后熄灭，此时此遥控器按键为自锁模

式。

c)设置互锁模式

(注意：如果需要设置互锁模式，需

要遥控器的两个新的不同的按键，

第一个按键对应的是“接通”，第

二个按键对应的是“断开”。) 按下

通断器按键4次。通断器RF红色指示

灯亮起，在红灯亮起期间，按下遥控

器新的按键，红灯闪烁两次，然后长

注意Note:

a)如果新学习的遥控器按键已经学习

过，通断器将不会学习此按键。可参

考本章第一部分全部清除已学习按键

后重新学习。

b)通断器最多能学习共十个按键，如

果需要清除不在使用的遥控器按键，

可参考本章第一部分全部清除已学习

按键后重新学习。

亮，此时按下遥控器另一个新的按键，

此时红灯闪烁两次，然后熄灭。此时

此遥控器按键为互锁模式。第一个按

键为接通，第二个按键为断开。

常见问题及解决办法

Q: 如何将指示灯设置为快闪

① 将设备接通电源，10秒后断电再接

通电源。

② 长按复位键5秒。

③ 确认指示灯快闪。

Q: 如何将指示灯设置为慢闪

① 将设备接通电源，10秒后断电再

接通电源。

② 长按复位键5秒。

③ 确认指示灯快闪。

④ 再次长按复位键5秒，直至指示灯

慢闪

注：新增加的设备需要1分钟连接WiFi

和互联网，如果长时间没有连上，请

通过WiFi状态来判断问题。

添加设备成功后，显示离

线，无法控制？

① 可能是wifi密码输入不正确.

② 可能是设备离您的路由器太远，信

号太弱，或环境有干扰。

③ 检查您的路由器后台是否开启MAC

地址过滤，如有，请关闭。

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnpu t

Output

WiFi Smart Switch

lnput

Output

Smart Life

RF 433MHz remote control setting

(if) . The RF LED is red.

A.Clear function

After push the receiver's learning

button 8 times, the receiver Clear all

the remote control data in it's memory.

When the LED flashes for the few

times, it indicates that the clear

function is completed.

(After cleared the code in the receiver,

all the remote control must study

from receiver once again to restart. )

B.About receiver's Working Mode

a)Momentary mode

Press the Remote control button,

the receiver's relay is ON, release

button, the receiver's relay is off.

b)Toggle mode

Press Remote control button for 1 time,

the receiver's relay is on ;Press button

again, the receiver's relay is OFF.

c)Latched mode

Press Remote control button A, the

receiver's relay is ON, Press the

transmitter's button B,the receiver's

relay is OFF

C.Receiver operating mode settings

a)Setting momentary Mode

Press the receiver's Learning button 2

times, The receiver's RF LED will be

lights up red, it comes into Setting

state, Press the remote's button, the

receiver's LED will be flash red twice

then come off, Setting successfully.

b)Setting Toggle Mode

Press the receiver's Learning button 3

times, The receiver's RF LED will be

lights up red, it comes into Setting

state, Press the remote's button, the

receiver's LED will be flash red twice

then come off, Setting successfully.

c)Setting Latched Mode

(Note: When you choose＂Latched

Mode＂,you need to setting two

different buttons on the Remote

Control, the first time learn is for “ON”,

the second time learn for “OFF”. For

Example: Button A= ON, Button B=OFF)

Press the receiver's Learning button

4 times, The receiver's RF LED will

be lights up red, it comes into Setting

state. Press the remote's button A,

the receiver's RF LED will be flash red

twice and lights up; Then press the

remote's button B, the receiver's

RF LED will be flash red twice and

come off. Setting successfully.

D.Note: every receiver just can learn

Ten remote's buttons. If you will

delete the remote's buttons, you can

push the receiver's learning button 8

times, the receiver Clear all the remote

control data in it's memory, and learn

the again.

RF 433Mhz遥控功能指示灯

（如有）是红色

一、清除所有已配对RF遥控器：

通电状态下，按键连按8次，红色指

示灯闪烁然后熄灭，清除完成。所

有已配对的遥控器均已清除。

二、RF工作模式解释：

1)点动模式：按下遥控器按键，通

断器接通，松开遥控器按键，通断

器断开。

2)自锁模式：按一次遥控器按键，

通断器转换一次开关状态。

3)互锁模式：需要设置两个按键，

按A按键接通，按B按键断开。

三、通断器RF 433MHz模式设置及

按键配对

1)点动模式：连续按下通断器按键2

次，通断器红灯亮起，按下要配对

的遥控器按键，通断器收到信号后，

红色指示灯短暂闪烁，然后熄灭。

设置完成。

2)自锁模式：连续按下通断器按键

3次，通断器红灯亮起，按下要配对

的遥控器按键，通断器收到信号后，

红色指示灯短暂闪烁，然后熄灭。设

置完成。

3)互锁模式：需要设置两个按键，

按A按键接通，按B按键断开。连续按

下通断器按键4次，通断器红灯亮起，

按下要配对的遥控器A按键，通断器

收到信号后，红色指示灯短暂闪烁，

然后长亮，此时再按下要配对的遥

控器B按键，通断器收到信号后，红

色指示灯短暂闪烁，然后熄灭。设

置完成。

四、注意：

1)通断器一共仅能学习十个遥控器

按键，如果超过，参考第一步清除

已配对按键。

2)每个遥控器按键仅能对应一个状

态，如果某个遥控器按键已经被学

习过，再次配对此按键时，通断器

指示灯不会接受此按键。

NOTE: This equipment has been tested

and found to comply with the limits for a

Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are

designed to provide reasonable

protection against harmful interference

in a residential installation. This

equipment generates, uses and can

radiate radio frequency energy and,

if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications.

However,there is no guarantee that

interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television

reception,which can be determined

by turning the equipment off and on,

the user is encouraged to try to correct

the interference by one or more of the

following measures:

-- Reorient or relocate the receiving

antenna.

-- Increase the separation between the

equipment and receiver.

-- Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced

radio/TV technician for help.

Summary of content (2 pages)

PAGE 1
L WiFi Smart Switch L N N L 4. 2 Celling lamp wiring instruction. checklist:before using the device 3 4 Register an Intelligent life account. L WiFi Smart Switch N N 4. 3 One wire wiring instruction. L L WiFi Smart Switch L N N L W iF i/ G PR S WiFi Android IOS N Note: The ONOFF switch must be powered up by N and L wires.
PAGE 2
FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.