Assembly Instructions

XX
Y
Y
A
1
B
C
D
2 3 4
A
B
C
D
1 2 3 4
DRAWING NO.
HI-P CORPORATION
PART NAME
SAP NO.
MATERIAL
3D VER.
2D VER.
SCALE
UNIT
SHEET
CONFIDENTIAL
PROJECT NAME
62.95±0.15
29.87
1.6
56.9±0.1
19.2 0.1
1.3
4(2x)
(2x)2.5 0.1
1.23
3(2x)
23.89
20.53 0.1
20.79 0.1
12
14.2 0.1
14.42 0.1
11.9
41.83±0.1
90°
0.91(2x)
(7.5)
14.77
11.07±0.1
35.37±0.1
0.3
2.05
0
-0.1
0.8
13.14±0.05
0.69
10.37±0.1
10°
2D VER. ECN NO. DESCRIPTION DATE DESIGNED APPROVED
1 Initial Release 18-05-28
WangZhongding
Victor.Ge
1.1 for handle,button assembly 18-05-31 WangZhongding Victor.Ge
1.2 for button assembly, TPE bonding,add rib,thicken wall 18-07-22 WangZhongding Victor.Ge
1.3 add round on catch hole, update dimension 18-09-21 WangZhongding Victor.Ge
Radiant ETB 1.3
T36C_BODY_ASSY T36C-0003 1.3 SIGNATURE DATE
DESIGNED
WangZhongding
18-04-15
see notes 1:1 MM 1 OF 1CHECKED TC. Tan 18-05-28
APPROVED Victor.Ge 18-05-28 COPYRIGHT 2015 HI-P R D CENTER CREATED BY CREO SIZE:A3
CUSTOMER P/N:
TOLERANCE UNLESS SPECIAL SPECIFIED
SELECT CLASS M
LINE
DIMENSIONS
CLASS F M C
0.00-3.00 0.05 0.10 0.20
(3.00)-6.00 0.05 0.10 0.30
(6.00)-30.00 0.10 0.20 0.50
(30.00)-120.00 0.15 0.30 0.80
(120.00)-INFINITY 0.20 0.50 1.20
RADII AND
CHAMFER HEIGHTS
0.00-3.00 0.20 0.40
(3.00)-6.00 0.50 1.00
(6.00)-INFINITY 1.00 2.00
ANGULAR
DIMENSIONS
0.0-10.0 0.2 0.3
(10.0)-50.0 0.3 0.5
(50.0)-120.0 0.5 1.0
(120.0)-INFINITY 1.0 1.5
For MP tool
For prototype tool
Item Part Name Material Process Finishing Remark
1 T36C_BODY ABS PA758 Injection
A3
VDI 21 in designated area
2 T36C_BODY_TPE
TPE
TPE DE30600, Shore A30°
Double shot VDI-24
3 T36C_BODY_CAP ABS PA757 Overmolding
Outter surface:A2
Inner surface:B1
NOTES:
1. Material: refer to table
Finish: refer to table
PART MUST BE MOLDED USING 100% VIRGIN MATERIA.
2. DIMENSIONS:
2.1 Inspection dimensions marked with " " are critical dimensions
and their CPK>=1.33.
2.2 SPC control dimensions are marked with " SPC " and their CPK>=1.33.
2.3 All dimensions without tolerance should comply
with the general tolerance table in drawing.
2.4 All features unspecified can be referred to the 3D data.
3. APPEARANCE:
3.1 Finished parts are to be clean and free from all foreign matter.
3.2 Part to be free from flash, sink marks, scratches, inclusions,
flow and weld lines.
3.3 Flash and parting line mismatch shall not exceed 0.05mm.
4. TOOLING REQUIREMENTS
4.1 Ejector pads shall not exceed 0.1mm above flush,nor 0.1mm
below flush to part surface.
4.2 Gate vestigital shall not exceed 0.1mm beyond the part surface.
4.3 Tooling marking as follows:
A. text: standard font, height: 2.5mm, depth: 0.2mm.
B. core to be marked with the following details:
*material; part number(P/N); *revision letter (1,2,3...)
*cavity number (C1/n,C2/n...Cn/n); *recycle symbol; *date code
5.The part should be comply with below regulation and/or directive
5.1.RoHS EU Directive 2011/65/EU and its amendments including EU 2015/863
5.2.China ROHS 2.0 5.3.REACH SVHCs
5.4.1935/2004/EC or FDA 5.5.GB 4806
5.6.ASTM F963 for heavy metals 5.7.EN 71-3 Category III for heavy metals
5.8.BPA Free 5.9.Phthalates (7) for CPSC-CH-C1001-09.3
5.10.PAHs (18) for German AfPS GS 2014 PAK Category 1
6.X with triangle mark means the changes in drawing version X.
Finished
VDI 21
VDI 21
add 12 ribs
SCALE 1:2
0.1
SECTION X-X
SEE DETAIL A
R1(4x)
SCALE 2:1
DETAIL A
SECTION Y-Y
1
2
SCALE 1:2
3
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.3
1.3